- Adds arbitration between the erase and write in suspend mode
(If the flash memory is suspended then only a read operation can be performed.)
- espcoredump: Dump does not use suspend feature, just resume before continue.
- spi_flash: Add release_cpu() to do suspend/release_cpu/resume
esp32s2: fix wrong deepsleep configuration issue.
1. if RTC_CK8M_ENABLE_WAIT_DEFAULT set to 1, rtc peripherals will not poweron successfully if pd peripherals in light_sleep, the minimum RTC_CK8M_ENABLE_WAIT_DEFAULT is RTC_POWERUP_CYCLES + RTC_WAIT_CYCLES + 2;
2. when goto deepsleep after lightsleep waking up, rtc regulator should not force pu.
- add lock for single read and continuous read APIs
- update onetime read start singal delay for hardware limitation[*]
- move adc_caps to soc_caps.h
- update license dates
[*] There is a hardware limitation. If the APB clock frequency is high, the
step of this reg signal: ``onetime_start`` may not be captured by the
ADC digital controller (when its clock frequency is too slow). A rough
estimate for this step should be at least 3 ADC digital controller
clock cycle.
There is no ccomp timer on C3, which means our performance tests will start
failing again due to variance caused by cache misses.
This MR adds TEST_PERFORMANCE_CCOMP_ macro that will only fail
performance test if CCOMP timer is supported on the target
* Target components pull in xtensa component directly
* Use CPU HAL where applicable
* Remove unnecessary xtensa headers
* Compilation changes necessary to support non-xtensa gcc types (ie int32_t/uint32_t is no
longer signed/unsigned int).
Changes come from internal branch commit a6723fc
During HAL layer refactoring and new chip bringup, we have several
caps.h for each part, to reduce the conflicts to minimum. But this is
The capabilities headers will be relataive stable once completely
written (maybe after the featues are supported by drivers).
Now ESP32 and ESP32-S2 drivers are relative stable, making it a good
time to combine all these caps.h into one soc_caps.h
This cleanup also move HAL config and pin config into separated files,
to make the responsibilities of these headers more clear. This is
helpful for the stabilities of soc_caps.h because we want to make it
public some day.
freertos/port: update the port files and split into xtensa and riscv ports
freertos: separated cpu files from rest of the kernel sources
freertos/port_xtensa: separated private include files into a folder
freertos/tasks: added task create pinned to core function do not break current IDF API
freertos/tasks: mimiced task create pinned function into tasks.c to do not break the IDF API.
freertos: freertos component now compiling
freertos: freertos component now building
freertos: moved critical sections outside from FR kernel section to portable section
portmacro_xtensa: add void indentifier on functions that take no arguments
freertos: fix critical sections implementation to match with their function prototype
freertos: add cmake changes of freertos into make
freertos: remove portDONT_DISCARD attribute from switch context function, it was breaking the docs building.
freertos: fix conflicitng types of vApplicationSleep function
license: update the license of freertos
freertos: Doxygen comments refactored to render them correctly on docs
freertos: added new functions of freertos into the documentation
freertos: added message buffers and stream buffers to documentation
sysview: update freertos system view to the compatible with version 10
freertos: fixed event group documentation rendering
freertos: update static task structure to match the actual tcb size
freertos: removed backported test functions
freertos/smp: brought SMP code to FreeRTOS 10 port
freertos/portmacro: added missing crosscore interrupt for yielding tasks
freertos: replaced soft-critical sections with hard-critical sections used by SMP
freertos: placed muxes inside of kernel objects
freertos: replaced original FR critical sections with SMP enabled spinlocks critical sections
freertos: moved xtensa port files to a separated folder
freertos: added multiple instance of global variables required to SMP
freertos: added SMP modifications on specific tasks module functions
freertos: added TLS deletion function to task module
freertos/tls: initialize TLS deletion callback to avoid crashing when calling task delete
freertos: modified vTaskDelete to do not erase current task that runs on other core
freertos: reverted taskhandle and timerhandle as void* type
freertos: fixed de-referencing void pointer to get run time counter
freertos: fix system view trace enter macro arguments
freertos: Replaced soft critical sections with spinlocks on event_groups
freertos: fixed tick function to avoid calling tick hooks twice
freertos: Nofity give checking per CPU if schedule is suspended
freertos: added mpu release on TCB deletion
freertos: Added SMP changes when deleting a TCB on idle task
freertos/license: update freertos license in COPYRIGHT.rst
freertos: unicore configurations can use task create pinned to core, it will be always pinned to core 0
freertos/portmacro: added cpu_hal_get_core_id() function instead of inline assembly
freertos/xtensa: update xtensa specific files used in master branch
newlib/locks: revert the preemption checking in lock acquisition and release
ref_clock: fix initial state of ref_clock interrupt handler
freertos: added missing critical sections and yielding checkings
freertos: remove magic numbers in vTaskDelete
freertos: added missing critical section in prvIsQueueEmpty
Fix for issues where RTC FAST memory is updated as part of going into deep
sleep. Very high risk if heaps are in RTC memory - in particular task stacks
may be in RTC memory, but also other variables.
Also fixes potential concurrency problems as RTC FAST memory is not accessible
by CPU during the CRC calculation itself.
Method:
- Disable interrupts (currently for single core only, will need update for S3)
- Load all registers before calculating CRC or going to sleep
1. The 2nd bootloader always call `rom_spiflash_unlock()`, but never help to clear the WEL bit when exit. This may cause system unstability.
This commit helps to clear WEL when flash configuration is done.
**RISK:** When the app starts, it didn't have to clear the WEL before it actually write/erase. But now the very first write/erase operation should be done after a WEL clear. Though the risk is little (all the following write/erase also need to clear the WEL), we still have to test this carefully, especially for those functions used by the OTA.
2. The `rom_spiflash_unlock()` function in the patch of ESP32 may (1) trigger the QPI, (2) clear the QE or (3) fail to unlock the ISSI chips.
Status register bitmap of ISSI chip and GD chip:
| SR | ISSI | GD25LQ32C |
| -- | ---- | --------- |
| 0 | WIP | WIP |
| 1 | WEL | WEL |
| 2 | BP0 | BP0 |
| 3 | BP1 | BP1 |
| 4 | BP2 | BP2 |
| 5 | BP3 | BP3 |
| 6 | QE | BP4 |
| 7 | SRWD | SRP0 |
| 8 | | SRP1 |
| 9 | | QE |
| 10 | | SUS2 |
| 11 | | LB1 |
| 12 | | LB2 |
| 13 | | LB3 |
| 14 | | CMP |
| 15 | | SUS1 |
QE bit of other chips are at the bit 9 of the status register (i.e. bit 1 of SR2), which should be read by RDSR2 command.
However, the RDSR2 (35H, Read Status 2) command for chip of other vendors happens to be the QIOEN (Enter QPI mode) command of ISSI chips. When the `rom_spiflash_unlock()` function trys to read SR2, it may trigger the QPI of ISSI chips.
Moreover, when `rom_spiflash_unlock()` try to clear the BP4 bit in the status register, QE (bit 6) of ISSI chip may be cleared by accident. Or if the ISSI chip doesn't accept WRSR command with argument of two bytes (since it only have status register of one byte), it may fail to clear the other protect bits (BP0~BP3) as expected.
This commit makes the `rom_spiflash_unlock()` check whether the vendor is issi. if so, `rom_spiflash_unlock()` only send RDSR to read the status register, send WRSR with only 1 byte argument, and also avoid clearing the QE bit (bit 6).
3. `rom_spiflash_unlock()` always send WRSR command to clear protection bits even when there is no protection bit active. And the execution of clearing status registers, which takes about 700us, will also happen even when there's no bits cleared.
This commit skips the clearing of status register if there is no protection bits active.
Also move the execute_flash_command to be a bootloader API; move
implementation of spi_flash_wrap_set to the bootloader
* changing dependencies from unity->cmock
* added component.mk and Makefile.projbuild
* ignore test dir in gen_esp_err_to_name.py
* added some brief introduction of CMock in IDF
ethernet: support flow control
Closes IDF-1207, WIFI-2510, WIFI-2290, WIFI-2291, WIFI-2507, WIFI-2508, WIFI-2612, and IDFGH-3465
See merge request espressif/esp-idf!9643
This commit simplies the defines made in the _caps.h header. Kconfig
option dependencies were moved into the LL, and the check for a
valid BRP has bee simplified.
Replace periph_module_enable/disable by periph_wifi_bt_common_module_enable which are in IRAM.
AddIRAM_ATTR periph_ll_wifi_bt_module_enable_clk_clear_rstandIRAM_ATTR periph_ll_wifi_bt_module_disable_clk_set_rstto fit O0 optimization level.
Delete duplicated spinlock and counter.
Including:
1. Change the write bytes/read bytes parameter in the host driver into slicers to meet the requirements of complicated cases.
2. Refactor the esp_flash_api code a bit so that we can use the code in the ROM laster
3. Provide get_temp_buffer and release_temp_buffer in the os_functions when the buffer passed by application cannot be used directly.
4. Make timeout of operations configurable in the chip_driver.
5. Make dummy number configurable.
This commit adds TWAI driver support for the
ESP32-S2. The following features were added:
- Expanded BRP support
- Expanded CLKOUT Divider Support
- Updated example READMEs
This fixes the issue where XTOS_SET_INTLEVEL would lower INTLEVEL from
4 to 3, when eTaskGetState is invoked during the core dump, triggered
from the interrupt watchdog.
When using DPort to read fifo, fifo_cnt is not credible, we need to calculate the real cnt based on the fifo read and write pointer. When using AHB to read FIFO, we can use fifo_cnt to indicate the data length in fifo.
On ESP32, due to fifo reset issue, UART2 will work incorrectly if reset the fifo of UART1(TX fifo and RX fifo). The software can workaround the RX fifo reset issue,
while the TX fifo reset issue can not. When UART2 is used and UART1 is used as the log output port, a software reset can reproduce this issue. So we should reset the UART memory
before the software reset to solve this problem.
Bugfix(I2S): Fix i2s_comm_format_t configuration parameter does not match the TRM bug
Closes IDFGH-3040, IDFGH-2913, IDFGH-578, IDFGH-2408, and IDFGH-3117
See merge request espressif/esp-idf!8339
- for ESP32 only enabled in case of unicore config
- capability wise this region (8K) is same as DRAM, except non-DMA capable
- also fixed small issue in reserved memory region processing when (start == end)
* Keep only USB related register operations in the LL.
* Move pad-related logic into the driver.
* Driver is now responsible for enabling the peripheral.
flash_encryption: modify additional efuses burning method to fix them are not being written
flass_encryption: burn efuse to disable boot from RAM space
flash_encryption: added better checking for key generation state plus set read and write protect for them
soc esp32s2: Add register-level bit definitions for read & wrote protect bits
esp32s2: Fixes for flash encryption
- Write efuses in a batch
- Fix some detection of whether existing efuse blocks are read/write protected
Previously, the test uses region 3 for the illegal access test
(0x60000000 - 0x7fffffff). This caused issues with there being
peripherals located in that memory range. Change to use region 4
(0x8000000 - 0x9fffffff) instead).
check master read write functions with array of registers)
fix master serial processing code and modbus controller to work with register array
modbus_master: add reading and writing of test value array (58 registers) to check failure is gone
remove parameter temporary buffer from modbus controller to allow more than 24 byte writes
driver: fix issue with TOUT feature
driver: fix uart_rx_timeout issue
driver: fix issue with rxfifo_tout_int_raw not triggered when received fifo_len = 120 byte and all bytes read out of fifo as result of rxfifo_full_int_raw
driver: add function uart_internal_set_always_rx_timeout() to always handle tout interrupt
examples: call uart_internal_set_always_rx_timeout() to handle tout interrupt correctly
examples: update examples to use tout feature
driver: reflect changes of uart_set_always_rx_timeout() function, change uart.c
driver: change conditions to trigger workaround for tout feature in uart.c
driver: change uart_set_always_rx_timeout()
freemodbus: fix tabs, remove commented code
driver: remove uart_ll_is_rx_idle()
tout_thr - move calculation and masking into hal layer update driver and uart_ll (add uart_ll_set_rx_tout)
move tout calculation into uart_ll
move calculation of time out in bit time for esp32s2 into low level uart_ll.h file
move uart_hal_get_symb_len() into hal
update set_rx_timeout() to warn user about incorrect value
update HAL, LL 1
fix uart_xx_set_rx_tout() to convert symbol time into bit time
update param description
update tout calculation in LL
update uart_hal_get_max_rx_timeout_thrd() and uart_ll_get_max_rx_timeout_thrd()
This commit updates the watchdog timers (MWDT and RWDT)
in the following ways:
- Add seprate LL for MWDT and RWDT.
- Add a combined WDT HAL for all Watchdog Timers
- Update int_wdt.c and task_wdt.c to use WDT HAL
- Remove most dependencies on LL or direct register access
in other components. They will now use the WDT HAL
- Update use of watchdogs (including RTC WDT) in bootloader and
startup code to use the HAL layer.
* Add test support for ESP32S2
* Add loop back test
* Support chip internal connection, no external wiring required.
* Delete the relevant codes of PDM of ESP32-S2 ll layer.
* fix dac dma mode issue
Goal is that multiple faults would be required to bypass a boot-time signature check.
- Also strengthens some address range checks for safe app memory addresses
- Change pre-enable logic to also check the bootloader signature before enabling SBV2 on ESP32
Add some additional checks for invalid sections:
- Sections only partially in DRAM or IRAM are invalid
- If a section is in D/IRAM, allow the possibility only some is in D/IRAM
- Only pass sections that are entirely in the same type of RTC memory region
Prefer assertions, making available functions only when caps support it
for cpu-related abstractions.
Changes cpu hal functions to stall, unstall, reset to not accept -1;
instead prefering macros that provide the same functionality.
Configurable option to use IRAM as byte accessible memory (in single core mode) using
load-store (non-word aligned and non-word size IRAM access specific) exception handlers.
This allows to use IRAM for use-cases where certain performance penalty
(upto 170 cpu cycles per load or store operation) is acceptable. Additional configuration
option has been provided to redirect mbedTLS specific in-out content length buffers to
IRAM (in single core mode), allows to save 20KB per TLS connection.
* Let `[ignore] case` return to freedom
1) Because this test uses its own ISR, we need to release it with `esp_intr_free` instead of `pcnt_isr_service_uninstall`.
2) `pcnt_evt_queue` needs to be created before the interrupt is registered and needs to be released at the end of each case.
* Add test support for ESP32S2
* Support chip internal connection, no external wiring required.
On the ESP32S2, rtc_clk_cal(RTC_CAL_RTC_MUX) measures the frequency
of the 90kHz RTC clock regardless of the selected slow clock
frequency. Keep track which clock is selected and pass the argument
to rtc_clk_cal accordingly.
fix clock choices
update rtc 32k xtal code for s2
missed api in rtc.h
bootloader_clock: update for S2
These definitions have ended up being chip specific. Moving them into
respective soc_memory_layout.c makes the whole picture of memory
regions easier to see, and also makes adding support for new chips
easier.
1. add brownout detector HAL for esp32 and esp32s2
2. enable brownout reset for esp32 rev. 1 and above
3. add approximate brownout detector levels for esp32s2
test_mux register doesn't exist in RTCCNTL anymore, remove it from
struct header. Also remove adc_ll_vref_output implementation, which
depends on that register.
spin_lock: cleaned-up port files and removed portmux files
components/soc: decoupled compare and set operations from FreeRTOS
soc/spinlock: filled initial implementation of spinlock refactor
It will decouple the spinlocks into separated components with not depencences of freertos
an similar interface was provided focusing the readabillity and maintenance, also
naming to spinlocks were adopted. On FreeRTOS side the legacy portMUX macros
gained a form of wrapper functions that calls the spinlocks component thus
minimizing the impact on RTOS side.
This feature aims to close IDF-967
soc/spinlock: spinlocks passed on unit test, missing test corner cases
components/compare_set: added better function namings plus minor performance optimization on spinlocks
soc/spinlock: code reordering to remove ISC C90 mix error
freertos/portmacro: gor rid of critical sections multiline macros, placed inline functions instead
soc/spinlock: improved spinlock performance from internal RAM
For cases where the spinlock is executed from IRAM, there is no
need to check where the spinlock object is placed on memory,
removing this checks caused a great improvement on performance.
1. use spi functions in rom
2. remove unnecessary GPIO configurations.
3. remove unnecessary dummy settings.
4. enable dummy out function
5. flash and psram have independent timing setting registers.
6. no need to set 1.9v for LDO in 80Mhz
7. set IO driver ability to 1 by default.
8. no need to use GPIO matrix on esp32s2, IO MUX is recommended
9. enable spi clock mode and IO mode settings
The following commit refactors the CAN driver such that
it is split into HAL and Lowlevel layers. The following
changes have also been made:
- Added bit field members to can_message_t as alternative
to message flags. Updated examples and docs accordingly
- Register field names and fields of can_dev_t updated
ledc_types.h includes two similar enums, ledc_clk_src_t & ledc_clk_cfg_t. Latter was added in
ESP-IDF v4.0.
The two enums do different things but there are two similar names: LEDC_REF_TICK / LEDC_USE_REF_TICK
and LEDC_APB_CLK / LEDC_USE_APB_CLK.
Because C will accept any enum or integer value for an enum argument, there's no easy way to check
the correct enum is passed without using static analysis.
To avoid accidental errors, make the numeric values for the two similarly named enums the same.,
Noticed when looking into https://github.com/espressif/esp-idf/issues/4476
* Modify the function implementation of ESP32-S2 RTC GPIO
On ESP32 those PADs which have RTC functions must set pullup/down/capability via RTC register.
On ESP32-S2, Digital IOs have their own registers to control pullup/down/capability, independent with RTC registers.
* Add ESP32-S2 support of unit test
* Modify the pull-up test of unit test
* Modify the interrupt test of unit test
* Modify input and output mode test of unit test
1. add hal and low-level layer for timer group
2. add callback functions to handle interrupt
3. add timer deinit function
4. add timer spinlock take function
There used to be dummy phase before out phase in common command
transactions. This corrupts the data.
The code before never actually operate (clear) the QE bit, once it finds
the QE bit is set. It's hard to check whether the QE set/disable
functions work well.
This commit:
1. Cancel the dummy phase
2. Set and clear the QE bit according to chip settings, allowing tests
for QE bits. However for some chips (Winbond for example), it's not
forced to clear the QE bit if not able to.
3. Also refactor to allow chip_generic and other chips to share the same
code to read and write qe bit; let common command and read command share
configure_host_io_mode.
4. Rename read mode to io mode since maybe we will write data with quad
mode one day.
1. simplify deallocate in esp_eth_mac_new_esp32, esp_eth_mac_new_dm9051
2. remove blocking operation in os timer callback
3. check buffer size in ethernet receive function
During coredump, dangerous-area-checking should be disabled, and cache
disabling should be replaced by a safer version.
Dangerous-area-checking used to be in the HAL, but it seems to be more
fit to os functions. So it's moved to os functions. Interfaces are
provided to switch between os functions during coredump.
The esp_flash API has a side effects: it modifies the clock control
registers, and this makes the clock inconsistent with the ROM variable
`g_rom_spiflash_dummy_len_plus`.
This commit helps the ROM to get the correct dummy cycles required by
the latest clock settings. Every device on the SPI1 bus will update the
ROM variable when it modifies the clock registers.
Do not include bootloader in flash target when secure boot is enabled.
Emit signing warning on all cases where signed apps are enabled (secure
boot and signed images)
Follow convention of capital letters for SECURE_BOOT_SIGNING_KEY
variable, since it is
relevant to other components, not just bootloader.
Pass signing key and verification key via config, not requiring
bootloader to know parent app dir.
Misc. variables name corrections
This commit refactors backtracing within the panic handler so that a common
function esp_backtrace_get_next_frame() is used iteratively to traverse a
callstack.
A esp_backtrace_print() function has also be added that allows the printing
of a backtrace at runtime. The esp_backtrace_print() function allows unity to
print the backtrace of failed test cases and jump back to the main test menu
without the need reset the chip. esp_backtrace_print() can also be used as a
debugging function by users.
- esp_stack_ptr_is_sane() moved to soc_memory_layout.h
- removed uncessary includes of "esp_debug_helpers.h"
Using xxx_periph.h in whole IDF instead of xxx_reg.h, xxx_struct.h, xxx_channel.h ... .
Cleaned up header files from unnecessary headers (releated to soc/... headers).
introduced in f871cc5ffa
The issue is caused by
1. The hal didn't pass the io_mode to LL.
2. The setup_device function overwrite the trans-specific settings.
This MR removes the common dependency from every IDF components to the SOC component.
Currently, in the ``idf_functions.cmake`` script, we include the header path of SOC component by default for all components.
But for better code organization (or maybe also benifits to the compiling speed), we may remove the dependency to SOC components for most components except the driver and kernel related components.
In CMAKE, we have two kinds of header visibilities (set by include path visibility):
(Assume component A --(depends on)--> B, B is the current component)
1. public (``COMPONENT_ADD_INCLUDEDIRS``): means this path is visible to other depending components (A) (visible to A and B)
2. private (``COMPONENT_PRIV_INCLUDEDIRS``): means this path is only visible to source files inside the component (visible to B only)
and we have two kinds of depending ways:
(Assume component A --(depends on)--> B --(depends on)--> C, B is the current component)
1. public (```COMPONENT_REQUIRES```): means B can access to public include path of C. All other components rely on you (A) will also be available for the public headers. (visible to A, B)
2. private (``COMPONENT_PRIV_REQUIRES``): means B can access to public include path of C, but don't propagate this relation to other components (A). (visible to B)
1. remove the common requirement in ``idf_functions.cmake``, this makes the SOC components invisible to all other components by default.
2. if a component (for example, DRIVER) really needs the dependency to SOC, add a private dependency to SOC for it.
3. some other components that don't really depends on the SOC may still meet some errors saying "can't find header soc/...", this is because it's depended component (DRIVER) incorrectly include the header of SOC in its public headers. Moving all this kind of #include into source files, or private headers
4. Fix the include requirements for some file which miss sufficient #include directives. (Previously they include some headers by the long long long header include link)
This is a breaking change. Previous code may depends on the long include chain.
You may need to include the following headers for some files after this commit:
- soc/soc.h
- soc/soc_memory_layout.h
- driver/gpio.h
- esp_sleep.h
The major broken include chain includes:
1. esp_system.h no longer includes esp_sleep.h. The latter includes driver/gpio.h and driver/touch_pad.h.
2. ets_sys.h no longer includes soc/soc.h
3. freertos/portmacro.h no longer includes soc/soc_memory_layout.h
some peripheral headers no longer includes their hw related headers, e.g. rom/gpio.h no longer includes soc/gpio_pins.h and soc/gpio_reg.h
BREAKING CHANGE
1. separate rom include files and linkscript to esp_rom
2. modefiy "include rom/xxx.h" to "include esp32/rom/xxx.h"
3. Forward compatible
4. update mqtt
soc unit tests have not been included when compiling with CMake,
because ../${SOC_NAME}/test was not evaluated relative to the
CMakeLists.txt directory.
Also call register_components() regardless of the presence of test
directory for particular target.
The following 2 compiler warnings are only reproducible when setting:
OPTIMIZATION_FLAGS = -Ofast
esp-idf/components/soc/esp32/rtc_clk.c:
In function 'rtc_clk_cpu_freq_get':
esp-idf/components/soc/esp32/rtc_clk.c:506:12:
error: 'freq' may be used uninitialized in this function
[-Werror=maybe-uninitialized]
return freq;
esp-idf/components/esp_ringbuf/ringbuf.c:
In function 'xRingbufferReceiveSplitFromISR':
esp-idf/components/esp_ringbuf/ringbuf.c:934:26:
error: 'pvTempTailItem' may be used uninitialized in this function
[-Werror=maybe-uninitialized]
*ppvTailItem = pvTempTailItem;
Closes https://github.com/espressif/esp-idf/pull/2878
1. fix error when fading is too fast
2. fix error when setting duty and update immediately
3. update register header file to be in accord with TRM
closes https://github.com/espressif/esp-idf/issues/2903
A workaround to reset BBPLL configuration after light sleep. Fixes the
issue that Wi-Fi can not receive packets after waking up from light
sleep.
Ref. https://github.com/espressif/esp-idf/issues/2711
The DMA cannot receive data correctly when the buffer address is not
WORD aligned. Currently we only check whether the buffer is in the DRAM
region.
The DMA always write in WORDs, so the length arguments should also be
multiples of 32 bits.
A check is added to see whether the buffer is WORD aligned and has valid
length.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
New unity component can be used for testing other applications.
Upstream version of Unity is included as a submodule.
Utilities specific to ESP-IDF unit tests (partitions, leak checking
setup/teardown functions, etc) are kept only in unit-test-app.
Kconfig options are added to allow disabling certain Unity features.
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
Introduced in 97e3542947.
The previous commit frees the IRAM part when single core, but doesn't
change the memory layout functions. The unit test mallocs IRAM memory
from the heap, accidently into the new-released region, which doesn't
match the memory layout function.
This commit update the memory layout function to fix this.
Some logging done in soc component may happen before logging via
stdout is possible. Use _EARLY version of log calls to make sure that
output is visible. The downside is that application does not have a
way to silence these logs. However since the soc component doesn’t
use any LOGV/LOGD/LOGI and only logs warnings and errors, this should
not impact the application.
When CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled, RTC data is placed
into RTC_FAST memory region, viewed from the data bus. However the
bootloader was missing a check that this region should not be
overwritten after deep sleep, which caused .rtc.bss segment to loose
its contents after wakeup.
Works for 3.3V eMMC in 4 line mode.
Not implemented:
- DDR mode for SD cards (UHS-I) also need voltage to be switched to 1.8V.
- 8-line DDR mode for eMMC to be implemented later.
Previous APIs used to set CPU frequency used CPU frequencies listed in
rtc_cpu_freq_t enumeration. This was problematic for two reasons.
First, supporting many possible frequency values obtained by dividing
XTAL frequency was hard, as every value would have to be listed in
the enumeration. Since different base XTAL frequencies are supported,
this further complicated things, since not all of these divided
frequencies would be valid for any given XTAL frequency. Second,
having to deal with enumeration values often involved switch
statements to convert between enumeration and MHz values, handle
PLL/XTAL frequencies separately, etc.
This change introduces rtc_cpu_freq_config_t structure, which contains
CPU frequency (in MHz) and information on how this frequency has to
be generated: clock source (XTAL/PLL), source frequency, clock
divider value. More fields can be added to this structure in the
future. This structure simplifies many parts of the code, since both
frequency value and frequency generation settings can be accessed in
any place in code without the need for conversions.
Additionally, this change adds setting of REF_TICK dividers to support
frequencies lower then XTAL with DFS.
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.
Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
No longer necessary to keep all reserved addresses in 'soc'.
Means 'soc' does not need to know about 'bt', for example.
Also means that Bluetooth can be enabled in config without any memory being reserved for BT
controller. Only if code calling the BT controller is linked in, will this memory be reserved...
Fixed the error division on zero.
Also fixed range CONFIG_ESP32_RTC_CLK_CAL_CYCLES in Kconfig.
Fixed a overflow error by TIMG in the function rtc_clk_cal_internal. This error was due to a limit in values TIMG_RTC_CALI_MAX=0x7FFF (to write the slowclk_cycles) and TIMG_RTC_CALI_VALUE=0x1FFFFFF (to read xtal_cycles). Added assert finctions.
Closes https://github.com/espressif/esp-idf/issues/2147
