SPI flash operations lock for shorter periods
Based on bug report here:
https://esp32.com/viewtopic.php?f=13&t=1489&p=6816#p6773
Long SPI flash erase (and possibly write/read) cycles block all tasks on both CPUs for an extended period, and can lead to WiFi dissassociation (and general priority inversion.)
This MR inserts preemption breaks into large operations (all erases, writes every 8KB, reads every 16KB).
Overhead of a single spi_flash_guart_start()/spi_flash_guard_end() cycle measured at approx 67us (assuming no preemption.)
See merge request !600
Error handling in NVS initialization
Previously nvs_flash_init worked under an assumption that there should always be at least one free page available. This is true during normal operation, but in some cases (such as when changing application partition table from a non-OTA to an OTA one), NVS partition may get truncated, which will cause empty pages to be lost.
This MR adds error checks for this condition, and updates code which calls `nvs_flash_init` to check for the return code.
For most examples, a simple `ESP_ERROR_CHECK` is added around `nvs_flash_init`. For NVS examples and the OTA example, more robust error handling is added.
This change also removes nvs_flash_init calls from examples which don't use NVS.
See merge request !582
idf_monitor: Small fixes (baud rate, EOL, /dev/tty.X on macOS, Ctrl-T on failure)
* "make monitor" now passed the configured baud rate.
Closes#436https://github.com/espressif/esp-idf/issues/436
* Pass toolchain prefix from sdkconfig into monitor tool
* Allow setting EOL in idf_monitor.py, use CRLF by default
* Detect if /dev/tty.X is used on macOS, warn and replace with /dev/cu.X
* If a build fails or gdb exits, ignore Ctrl-T (allowing Ctrl-T Ctrl-A/F to be same key sequence everywhere)
* Add a note about winpty on Windows.
Ref 02fdf8271d (commitcomment-21369196)
* Fix problems with Console.cancel() not existing in older pyserial
* Print more user-friendly symbols for "start of iram" and "start of flash"
See merge request !594
1. reset wifi mac when wifi start
2. roll back rx hung workaround for beacon timeout
3. fix amsdu ap interface wrong issue
4. fix amsdu header parse error
5. fix amsdu flag wrong issue
6. PHY: V350, fix BT rssi bug
7. RTC: V225, fix bt will be not work when wifi is reset
This is to avoid confusion when idf_monitor prints the first symbol in each section, ie "WindowOverflow4" or similar,
when bootloader prints the section mapping address.
Closes#447https://github.com/espressif/esp-idf/issues/447
1. Add low speed channels for LEDC module.
2. Improve fade object allocate mechanism.
3. Improve ledc example, add 2 low speed channels in example.
4. Remove debug code
5. Improve the register bit field name of slow clock.
1. add options to disable nvs
2. add station keepalive with softap
3. fix beacon rx start time not accurate issue
4. set wifi rx desc/buffer boundary check to internal memory boundary
add wakeup from touch sensor, and deep sleep example
- add new deep sleep wakeup mode
- change documentation to explain incompatibilities between different wakeup mode, add error checks
- add new ULP instructions necessary for ULP wakeup scenario
- fix issues with I_WR_REG, I_SLEEP, I_END instructions
- add deep sleep example, illustrating the use of timer, gpio, touch, and ULP wakeup triggers
See merge request !461
component/bt: optimize stack size of Bluetooth Tasks and make them be configurab…
Bluetooth tasks' stack size are optimized and can be configured by the CONFIG_NEWLIB_NANO_FORMAT option.
See merge request !559
Allow separate ethernet & wifi configuration
If only 1/2 of ethernet & WiFi are enabled in config, the other interface is no longer linked into the firmware.
* Fixes bug where enabling Ethernet but not WiFi would fail to compile.
* Also means that enabling WiFi but not Ethernet no longer links some unused ethernet interface functions.
See merge request !525
Feature/add user set mac
1. Add menuconfig for user to set mac address of wifi, bt and ethernet.
2. Add the number of MAC address generated from efuse for user to choose.
3. Add MAC address derive method.
See merge request !542
1. RTC V214: modify APLL function for the chip of ECO version.
2. Add API phy_close_rf() and use it in esp_phy_deinit() instead of pm_close_rf().
3. RTC V213: fix BT will not work when BT-init is called more than once.
Optimize or release memory in bluetooth
1. add option to release about 30K from BT if BLE only
2. later BT/BLE will be separated by BT/BLE macro, but this option should use when user make sure that in BLE only mode.
See merge request !520
This change adds esp_deep_sleep_get_wakeup_cause, which returns the
source which has caused wakeup from deep sleep.
Similar to esp_deep_sleep_get_ext1_wakeup_status, a function is added
to check touch pad wakeup status: esp_deep_sleep_get_touchpad_wakeup_status.
This function returns the touch pad which has caused wakeup.
ULP and touch FSMs in ESP32 revisions 0 and 1 do not operate correctly
if RTC_PERIPH power domain is force powered on (ESP_PD_OPTION_ON).
Both ULP and touch still work, but clock frequency of the ULP may be
incorrect and touch values may be off by considerable amount. As such,
when these wakeup modes are used, RTC_PERIPH power domain has to be set
to ESP_PD_OPTION_AUTO (or, in the current implementation,
ESP_PD_OPTION_OFF — though this will change in the future when _OFF will
actually *force* the power domain to be powered off).
Because EXT0 wakeup source requires RTC_PERIPH to be powered ON, mark
ULP and touch wakeup sources as incompatible with EXT0. Workaround for
this is to use EXT1 wakeup source instead, which offers similar or
better functions without having to keep RTC_PERIPH powered on.
In case WiFi/BT stack has been enabled but wasn’t disabled, some RTC
bits may be left enabled, causing increased current consumption.
This change returns some of the bits back to their default values.
1. add new APIs bt controller enable/disab/deinit
2. make bt controller work need to call two APIs of esp_bt_controller_init and enable
3. modify phy init to make mac reset once
1. add a macro in menuconfig for users to choose whether store phy calibration data into NVS or not.
2. rename some disable phy and rf APIs so that existing code which calls old APIS will fail to compile.
1. Add disable PHY and RF when WiFi and BT are both disabled(including call sniffer disable API).
2. Do not init PHY and RF when cpu start. Init PHY and RF when call Wifi or BT start APIs(including sniffer enable API).
3. Add a temporary lib: librtc_clk.a and will delete it when CPU frequency switching function is done.
4. Add an function to get OS tick rate.
5. Do not put the whole pp.a in iram0, only put lmac.o, ieee80211_misc.o, ets_time.o and wdev.o in iram0.
phy_init: don’t rewrite valid calibration data
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
See merge request !487
1. Reduce the default static rx buffer size from 25 to 10
2. Adjust ampdu interrupt size to 3, namely, raise 1 interrupt per 3-mpdu
3. Make a copy for all received packets, including AMSDU/AMPDU/MPDU
4. Fix softap mis-forward issue
5. Fix pp q full issue
6. Fix sniffer copy wrong content issue
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
esp32: Fixes watchdog problem when printing core dump to uart
1) Fixes watchdog problem when printing core dump to uart
2) Also fixes generation of core dumps when flash cache is disabled
See merge request !472
1. fix ampdu<->mpdu<->ampdu switch may cause rx slow issue by put mpdu into ampdu reorder queue
2. fix each ac first sending always fail issue by adding retry
1. modify the discover retry backoff time from (2,4,8,16,32,60,60)s to (500m,1,2,4,8,15,15)s.
2. add DHCP_DOES_ARP_CHECK to menuconfig for users to specify if do a ARP check on the offered address.
If enable, one more second will be taken in obtaining IP address.
3. update wifi libs
Move PHY options out of WiFi config, improve descriptions
- move PHY-related settings into new menu, make it dependent on WIFI_ENABLED || BT_ENABLED
- improve descriptions of Ethernet Kconfig options
See merge request !443
ESP32_PHY_MAX_TX_POWER option is only meaningful for WiFi, so previous
change made it depend on WIFI_ENABLED. However if WiFi is not enabled,
but BT is, this option becomes undefined which breaks phy_init_data
generation.
This change turns ESP32_PHY_MAX_TX_POWER into a hidden parameter, which
depends on PHY_ENABLED. New user-visible parameter,
ESP32_PHY_MAX_WIFI_TX_POWER is introduced which depends on WIFI_ENABLED
and is used as default value for ESP32_PHY_MAX_TX_POWER if WIFI_ENABLED
is set. Otherwise ESP32_PHY_MAX_WIFI_TX_POWER is set to 20.
fixes for issues observed when using spi_flash
This MR fixes three unrelated issues:
- Race condition in spi_flash_enable_interrupts_caches_and_other_cpu
when operations on unpinned tasks are performed.
The issue is reported in https://github.com/espressif/esp-idf/pull/258
- esp_intr_noniram_disable doesn’t disable interrupts when compiled in
release mode. This issue manifested itself with an illegal instruction
exception when task WDT ISR was called at the time when flash was
disabled.
Fixes https://github.com/espressif/esp-idf/issues/263.
- Tick hooks on CPU1 were not called if CPU0 scheduler was disabled for
significant amount of time (which could happen when doing flash erase).
The issue manifested itself as “INT WDT timeout on core 1” error.
Fixes https://github.com/espressif/esp-idf/issues/219.
See merge request !441
When compiling in release mode, compiler was choosing same register for
oldint and intmask variables, so INTENABLE was never modified.
This effectively broke disabling of non-IRAM interrupts during flash
operations, observed in the existing tests if task watchdog is enabled.
This change adds an extra constraint tells the compiler that output
operand should not be placed into the same register as an input one.
Delete option to select core timer 2 as a FreeRTOS tick source
Core timer 2 is unusable for FreeRTOS ticks because it triggers a high-level interrupt. This MR deletes the option to select it.
Ref https://github.com/espressif/esp-idf/issues/234
See merge request !418
update wifi lib: fix some wifi lib bugs
1. net80211: fix get ap info error(a4614877)
2. tw9358: sta mac same with softap(ea38d32c)
3. tw9221: scan channel error when connected(183d469c)
See merge request !425
fixes for github issues
This MR includes commits from several Github PRs, as well some fixes for issues reported on Github and on the forum.
- compile PHY-related code only when WiFi is enabled
- fix macOS setup instructions
- fix some of the Sphinx warnings
- update docs index, improve structure of the readme-
- wifi: fix typos, rename ESP_ERR_WIFI_NOT_START to ESP_ERR_WIFI_NOT_STARTED
- sdmmc: fix explanation of flash voltage regulator configuration efuses
- sdmmc: change idx num of example
- fix i2c_get_period name
- fix esp_log_level_set function name in docs
See merge request !420
If using WIFI_INIT_CONFIG_DEFAULT, error message will point out lack
of WiFi. Otherwise linker errors on WiFi symbols should help give a
clue as to what is broken.
Piggy-backs on changes in !420, ref github #230#237
esp32 core dump to flash
1. menuconfig option to select where to store core dump: flash, uart or disable
2. Saving of core dump to flash
3. Partition table definitions files with core dump partition
4. Python scripts to support core dump generation from GDB command line
See merge request !341
The following issues mentioned during MR!341 review were fixed:
1) Core dump test application description
2) Usage of CONFIG_ESP32_ENABLE_COREDUMP_TO_FLASH and CONFIG_ESP32_ENABLE_COREDUMP_TO_UART
3) FLASH_GUARD_START macro usage is fixed in flash API
4) Core dump module logging facility
5) cache util functions doc updated
6) interactive delay before print core dump to uart
7) core dump partion support in build system
Deep sleep stub may call ets_update_cpu_frequency, which has been moved from ROM to IRAM.
Restore the ROM version in the linker script, call it ets_update_cpu_frequency_rom, use it in the deep sleep stub.
1) PS is fixed up to allow GDB backtrace to work properly
2) MR!341 discussion: in core dump module: esp_panicPutXXX was replaced by ets_printf.
3) MR!341 discussion: core dump flash magic number was changed.
4) MR!341 discussion: SPI flash access API was redesigned to allow flexible critical section management.
5) test app for core dump feature was added
6) fixed base64 file reading issues on Windows platform
7) now raw bin core file is deleted upon core loader failure by epscoredump.py
Complimentary changes:
1) Partition table definitions files with core dump partition
2) Special sub-type for core dump partition
3) Special version of spi_flash_xxx
4) espcoredump.py is script to get core dump from flash and print useful info
5) FreeRTOS API was extended to get tasks snapshots
Clean up WiFi & Bluetooth config options
* Splits "WiFi" configuration out from ESP32 configuration submenu to its own menu.
* Renames "BT" to "Bluetooth", enabling Bluetooth is now in this option not the ESP32 submenu.
* Also disables compiling/linking of BT stack if Bluetooth is disabled, saves some build time.
See merge request !397
add wpa2 set id api and modify null data tx description
1. wpa2: add wpa2 set id api
2. low rate: modify null data tx description
See merge request !402
ethernet: support flow control
(1) Only fullduplex mode support flow ctrl .
(2) Fix reboot exception which caused by not-reset EMAC hardware (such as DMA) when reset CPU.
See merge request !392
Add option to automatically set a watchpoint at the end of the swapped-in task
This should make stack overflows easier to debug because it triggers a debug exception as soon as the stack is overwritten, not later when a context switch happens. Marked as a FreeRTOS debug feature because it doesn't give a nice error message and uses up a watchpoint.
See merge request !389
Fix OpenOCD detection code
In the current master, detection of an attached OCD is broken. This fixes it.
I also snuck in two unrelated checks in intr_alloc which return from a function that is asserted earlier in the code. This makes the code behave better when they are called erroneously in a production build.
See merge request !377
SDMMC peripheral driver, SD protocol driver, FATFS library, VFS integration
This MR contains:
- SDMMC host peripheral driver
- SD protocol driver in sdmmc component (can be extended to support MMC/eMMC and SPI based hosts)
- ChaN's FATFS library v0.12b
- VFS integration
- FAT access via VFS is thread-safe (unless same file is read/written/unlinked/renamed from different tasks)
- Support for POSIX directory-related functions in VFS (and in vfs_fatfs.c)
- unit test for the above
- Example
- API documentation
Will be done in other MRs:
- Support for spi_flash IO driver for FatFs
- SPI host driver and support for SPI mode commands in sdmmc component
- MMC/eMMC support in sdmmc component
- Support for slightly higher 53/26.6MHz clocks (currently I'm using 20MHz for DS and 40MHz for HS, instead of 25MHz/50MHz per standard), and arbitrary low clocks (e.g. 4MHz).
See merge request !353
C++ support
This change adds necessary support for compiling C++ programs:
- linking against libstdc++
- implementation of static initialization guards using FreeRTOS primitives: since we don't have condition variables at our disposal, and we don't want to allocate a synchronization primitive for every guard variable generated by the compiler, we imitate condition variables using a combination of a mutex, counting semaphore, and a counter (based on [Microsoft Research paper](https://www.microsoft.com/en-us/research/wp-content/uploads/2004/12/ImplementingCVs.pdf), albeit because we don't need *arbitrary* code to use these CVs, implementation gets simpler).
Note that libstdc++ also contains an implementation of `__cxa_guard_{acquire,release,abort}` functions. These implementations come from an `#ifndef GXX_THREADS` branch, i.e. are not aware of multthreading. There are three ways of replacing these libstdc++ functions with our implementation:
1. Move our code into gcc. Pros: cleanest solution. Cons: Such changes are unlikely to be merged by any upstream, so we end up maintaining our own forks of {gcc,crosstool-ng}.
2. Use library as it is built by crosstool, use `ar` to delete one object file (`guards.o`), add this library to ESP-IDF. Pros: easy to implement. Cons: libstdc++ is a 15MB binary 😯
3. Keep using libstdc++ from crosstool, force our implementation to be linked using a `-u` linker flag. Pros: no impact on repo size, easy to implement. Cons: somewhat less clean than 1 (and about as hacky as 2).
For the reasons mentioned, option (3) looks like the best tradeoff.
Ref. TW6702
See merge request !364
Enable bootloader entropy source for RNG
Enables an entropy source when bootloader starts up, which both seeds the RNG for use before WiFi/BT stack is enabled and provides an adequate RNG for secure boot & flash encryption key generation.
A prerequisite was enabling 80MHz operation, so the CPU is now set to 80MHz as soon as second stage bootloader starts running.
See merge request !363
esp32: ets_update_cpu_frequency should set tick scale for both CPUs
ets_update_cpu_frequency ROM function updates g_ticks_per_us, which is has two copies, one for each CPU.
The APP CPU copy of g_ticks_per_us never got updated, resulting in shorter delays produced by ets_delay_us on the APP CPU.
This MR replaces ROM ets_update_cpu_frequency with a copy in IRAM which updates scaling factors on both of the CPUs.
So now we get expected delays (in microseconds):
```
ets_delay_us core=0 expected=50000 actual=50014
ets_delay_us core=1 expected=50000 actual=50015
vTaskDelay core=0 expected=50000 actual=49428
vTaskDelay core=1 expected=50000 actual=50000
```
Reported on the forum: http://esp32.com/viewtopic.php?f=2&t=713#p3722
See merge request !373
SPI master driver
This merge requests adds an SPI Master driver. This driver is (of course) multithread capable, has device abstraction, has command queueing, DMA support and all other sorts of nice things you'd expect from a SPI driver.
See merge request !332
modify bootloader dram start address, swap app bss and data segments
Modify bootloader dram_seg from address 0x3ffc0000 to 0x3fff0000, len from 0x20000 to 0x10000.
Also put app .data before .bss, to reduce the chance .data collides with ROM bootloader stack.
See merge request !375
This change reduces chances that a large .bss segment will push .data all the way into
0x3ffe1320 — 0x3ffe5320 range where the bootloader stack is, creating a problem when
bootloader will be loading application into memory.
With this change, .data would need to be at least 200k big to cause problems.
1. Update wifi lib which contains ampdu and other optimizations
2. Add throughput code debug code
3. Other misc modification about throughput optimization
2. update example comments and other minor changes
3. rename API: i2c_cmd_link_create/i2c_cmd_link_delete (+4 squashed commits)
Squashed commits:
[2e0ac3e] 1. coding style: add one space after condition key words.
2. modify i2c.h, use gpio_num_t instead of int, improve comments of return values
3. add i2c index in index.rst
4. add readme for i2c example
[4991d92] update i2c.doc
[88b672e] driver: i2c
1. add mux and spin lock to run in a thread-safe way.
2. modify example code
[4eb15fe] driver: i2c code
1. add i2c master code
2. add i2c slave code
3. add i2c example code
4. add DRAM_ATTR for I2C array
Minor fixes from various sources
- Fix memory debugging code. Noticed by Tuan.
- intr_enable/disable should be in IRAM. Noticed by rojer
- Still old timer code in examples in doxygen comments. Noticed on the forum by jumjum123
- Timer example was broken. Noticed on the forum by jumjum123
See merge request !325
1. add sigma-delta code and example.
2. add gpio output signal in io matrix.
Squashed commits:
[a25e7d4] minor changes for doc
[6a03a1e] minor changes on comments and doc.
[97dd9e4] Add doc.
update index.rst
change example index
This change allows setting pin configuration for EXT1 wakeup depending on the state of RTC_PERIPH power domain:
- if peripherals are enabled (due to another wakeup mode, or due to esp_deep_sleep_pd_config call), we can keep internal pullups/pulldowns enabled
- if peripherals are disabled, pullups and pulldowns need to be disabled as well
Also add comments about the purpose of registers being configured.
This adds a workaround for a bug that following deep sleep wakeup, ISO (bus isolation) signal may be set for RTC fast memory.
We set FORCE_NOISO bit in RTC_CNTL_PWC_REG until we find out what is causing ISO signal to be set.
When ESP32 wakes up from deep sleep, flash is accessed an approximately 900us after power on.
Some flash chips need more time to become ready. This change adds a menuconfig option to add
some delay to the default deep sleep wake stub.
Fixes https://github.com/espressif/esp-idf/issues/117
This adds the following APIs to enable various wakeup sources:
- esp_deep_sleep_enable_timer_wakeup
- esp_deep_sleep_enable_ulp_wakeup
- esp_deep_sleep_enable_ext0_wakeup
- esp_deep_sleep_enable_ext1_wakeup
And an API to start deep sleep:
- esp_deep_sleep_start
1. TW8657, WIFI send the whole packet to smartconfig;
2. modify API annotation of smartconfig and sniffer;
3. export smartconfig APIs to programming guide;
build system: Linker scripts or binary libraries should trigger a re-link
Add binary libraries and linker scripts to the list of dependencies for the ELF file.
Fixes TW7816.
See merge request !307
Flash encryption support
Flash encryption support in build system, tooling
To come in future MR:
* On-device key generation on first boot (for production devices), need to finalise testing of bootloader entropy seeding.
* spi_flash_encrypted_write to support non-32-byte block writes (at least optionally.)
* I think a lot of the bootloader_support component can possibly be rolled into "spiflash" and other components, to use a common API.
See merge request !240
Add dynamic interrupt allocation mechanism
This adds:
- Dynamic allocation of interrupts. Pass it the features of the interrupt you want, it'll set you up with an int.
- Shared interrupts. Enables multiple peripheral drivers to use the same interrupt.
- Marking what interrupts are fully executable from IRAM; if an int isn't marked like that it will get disabled once flash cache gets disabled.
Also:
- Modifies driver to be in line with these changes
See merge request !254
newlib: add "full" formatting support
This change adds support for 64-bit formats and C99 features to newlib printf/scanf functions. This support is enabled by default in menuconfig, but can be switched off to reduce code size.
Also adds missing functions such as fmod and fmodf.
- Fixes https://github.com/espressif/esp-idf/issues/52
- Fixes https://github.com/espressif/esp-idf/issues/83
See merge request !274
- add two versions of libc: libc.a and libc_nano.a. First one has full C99 formatting support, second one uses “nano” formatting functions available in ROM.
- fix linker error for fmod, fmodf, atof, atoff
- update tests
On Xtensa windowed ABI backtrace is easy to do, and it's immensely
useful for debugging, so - do it by default.
We try to be careful and not deref bogus pointers while walking the
frames.
Example output (from debugging espressif/esp-idf#133):
Backtrace: 0x1:0x3ffc51e0 0x400e9dfa:0x3ffc5210 0x400e9ebc:0x3ffc5230 0x400ec487:0x3ffc5260
With just addr2line utility from binutils, this already pinpoints the
location of the crash.
Boot watchdogs were disabled very early in startup code. It was possible to introduce an infinite loop anywhere in the many functions called from startup code, and this would not be detected by interrupt watchdog and task watchdog. This change postpones disabling of boot watchdogs to the point when the scheduler is running. Also replaces register expressed using integer address with a name.
- ROM function uart_tx_wait_idle may have a bug which causes the function to return before the final character is fully transmitted.
This replaces uart_tx_wait_idle declaration with a static inline definition which fixes the issue.
- Also replaces the use of uart_tx_flush with uart_tx_wait_idle in esp_restart, to remove garbage in console output on restart.
- rtc_printf is temporary replaced with a no-op, pending a new release of librtc.a. Current release assumes that UART0 is used for output,
and switches UART0 baud rate while doing frequency changes and printing some log output. This doesn’t work if a different UART is used for output.
This change adds a set of menuconfig options to set custom UART#, baud rate, and pins, for console output.
Setting happens in bootloader startup code for PRO CPU, and in application startup code for APP CPU.
Ref. TW8146
feature(rtc_module):add rtc module
1. add rtc io control API (pull,output and input)
2. add touch pad API (touch pad read and interrupt)
3. add adc1 API (the max width is 12 Bits and support attenuation)
4. add hall sensor API (support hall sensor read )
5. add dac API (the width is 8 Bits)
bugfix(gpio):gpio32 and gpio33 can not output and input
the gpio32 and gpio33 is initialize by librtc.a,and gpio_config not initialize the gpio as
digital gpio.they can not output and input,when users use gpio32 or gpio33.And there are some problems
about others driver ,when they use gpio32 or gpio33 as matrix.
Small debugging fixes
Invoke panic handler when a stack overflow has been detected; unhandled interrupt handler now prints interrupt/cpu number for easier pinning down of source.
See merge request !277
Gdbstub: Fix bug, small cleanup
Tianzhongxing found a small bug preventing gdbstub to work in certain cases. This fixes it, as well as including some minor cleanups.
See merge request !260
* App access functions are all flash encryption-aware
* Documentation for flash encryption
* Partition read/write is flash aware
* New encrypted write function
Feature/btdm bluedroid
This branch contain the bluedroid host code.
Currently, Only GAP/GATT SERVER/GATT CLIENT release to users.
Actually, the content of the codes is further more than GAP/GATT and etc.
In this release version, users only need to concern about the APIs which are in "api/include/".
Now, suggestions in comment have been resolved are following:
1. The APIs use callback function. Ivan , Jeroen and me have discussed it. Currently the code will not be changed.
2. The APIs use OPEN/CLOSE. I have ask Ivan, besides bluedroid do this, we will keep the name.
3. Coding style. I have run format.sh to handle the style. And some spell error have been fixed.
4. APIs doxygen. I have clean the warning by doxygen. But bt.rst is still need to be completed.
5. Other comment without resolved face to face that I have to add response in the comment and fix them in the code
6. Fix some incorrect things. See the git log for details.
This 1st version of bluedroid release still have lots of things to do. But it can be done after this merge.
1. Compelete the BLUFI(Bluetooth config wifi connection) documents, security, application protocol and other.
2. Add SPP-LIKE profile.
3. Do more examples codes to cover most of the APIs.
4. Test and fix bug.
Another thing：
1. Do the document of APIs.(xml->bt.rst->html)
(I will do this before merge as Ivan's suggestion)
This is already done. Besides, the union type in doxygen have something error. Ivan will fix it.
See merge request !239
1. fix tw8911 sleep in scan leads to auth frame malloc fail.
2. fix tw8913 pm state transfer wrong leads to wdt.
3. make some comments for modem sleep and wpa2 enterprise.
4. removd duplicated debug option ESP_THREAD_SAFE_DEBUG
In AP bridge mode, the length of the forwarded data is wrong, it's 26Btyes longer, thus cuase
AP can't forward the data of which length is more than 1460. This modification is to make the
data length right.
1. update phy to version 258 to fix wifi upgrade cause wifi connect fail issue
2. update fix_printf.sh
3. fb5a2b07 - default set ps type to WIFI_PS_NONE
Bugfix mbedtls sha384 clone()
mbedtls_sha512_clone() on a SHA-384 hash caused incorrect digest
Also adds additional mbedtls unit tests into the unit tests project (including one for this bug).
See merge request !252
SHA acceleration integrated to mbedTLS incl. TLS sessions
Uses hardware SHA acceleration where available, fails over to software where not available.
Ref TW7112
See merge request !232
spi_flash_erase_range: Allow for 32KB blocks not 64KB blocks
SPI flash hardware sends 52h command, which is a 32KB erase.
There is a matching bug in the ROM SPIEraseArea code, unless
flashchip->block_size is modified first.
See merge request !249
driver: PCNT
1. add PCNT module in periph_ctrl.c/.h
2. add description of PCNT status in pcnt_struct.h
3. add PCNT driver code
4. add PCNT example code.
See merge request !229
system_* APIs cleanup
This changeset is mostly about cleaning up `system_*` APIs and moving them from libcore. It has dragged a few more changes along, however.
- `system_deep_sleep` deprecated, new name is `esp_deep_sleep`
- `system_efuse_read_mac` deprecated, new name is `esp_efuse_read_mac`
- `system_read/write_rtc_mem` removed (reason: we use linker to place code/data into RTC memory now)
- `system_get_sdk_version` deprecated. Returns "master" for now. Support for compile-time and runtime version detection will be done in a separate MR.
- `system_get_time` and variations have been deprecated. `gettimeofday` should be used instead.
- `system_restart` deprecated, new name is `esp_restart`. Rewritten code to work correctly from any of the cores.
- `system_restore` deprecated, `esp_wifi_restore` should be used instead.
- `system_get_rst_info` removed (it wasn't in a header file)
- RTC library has been updated to latest version
- Logging output from `libfoo.a` goes through `foo_printf` function now, where `foo ` is any of the library names. For libraries other than rtc and phy, this is a temporary measure, until we finish switching to esp_log library and clean up all uses of printf/ets_printf.
- ESP-IDF build will fail if any of the libraries have printf/ets_printf reference.
- Added `esp_random` function which gets values from HW RNG. I have added code which makes sure the value is not polled too often (allows at least 16 APB cycles). Also added a header file for HW RNG (just one register).
- Moved random number generation functions used by wpa library into wpa_supplicant component.
See merge request !234
SPI flash hardware sends 52h command, which is a 32KB erase.
There is a matching bug in the ROM SPIEraseArea code, unless
flashchip->block_size is modified first.
Integrate unit tests into build system
This MR moves unit tests from esp-idf-tests repository into 'test' subdirectories of respective components.
Tests are run using a runner app in tools/unit-test-app.
This needs a bit of cleanup:
1. remove extra newlines added to makefiles,
2. re-format unit tests code which has tabs
3. write a document on using this test app
4. maybe some refactoring in project.mk
I think 1&2&4 need to be done in this MR, while 3 may be done in a follow-up one.
See merge request !221
SHA hardware allows each of SHA1, SHA256, SHA384&SHA512 to calculate digests
concurrently.
Currently incompatible with AES acceleration due to a hardware reset problem.
Ref TW7111.
rename nvs host test folder, modify .gitlab-ci.yml
remove unit-test-app build
re-format unit test files
remove extra newlines in project.mk
some refactoring for unit test part in project.mk
add build files of unit-test-app in gitignore
add README.md for unit test app
correct headings in README.md
remove files and make minor tweaks in unit test app
update .gitlab-ci.yml to use unit test app
delete unused lines in component_wrapper.mk
delete periph_i2s.h and lcd test
add text floating point in components/esp32/test/Kconfig
correct idf test build paths in .gitlab-ci.yml
This change fixes the ESP32 watchdog issue. When the MPDU of AMPDU is longer than 1600B,
esp32 will check whether the last 4B is DEADBEEF, if it's not DEADBEEF, it will assert
and the assert will cause esp32 watchdog. The solution is to init the last 4B to DEADBEEF
when malloc new ebuf for the packet longer than 1600B.
hwcryto bignum support for RSA operations
Supporting RSA with hardware bignum directives.
Configurable via menuconfig to enable/disable, and to choose between busywaiting and interrupt driven completion.
May still be some performance tweaks possible.
TW7111
See merge request !92
Docs: new documentation and warnings cleanup
This change set
- adds a high-level description of application startup flow. Some parts are missing, but hopefully we can use this description as a base to expand on.
- adds a few notes about memory regions and their use in ESP-IDF.
- add SPI flash and partition APIs page
- fixes all Doxygen warnings in header files
- enables build failures on new Doxygen warnings
See merge request !201
Secure boot related fixes
Fix some issues (mostly build system) from the secure boot implementation
Also refactor the way submodule checks are applied to make them more reliable.
See merge request !207
Required at project level because some components use header files in
other components' submodules, and one component with a
submodule (esptool.py) doesn't have or need a component.mk.
Per-CPU interrupt handlers and args
Up to now, the interrupt handlers and args were shared between CPUs, that is, if you set an interrupt handler on CPU0, CPU1 would invoke the same interrupt handler on that interrupt. This code gives every CPU its own space for interrupt handlers.
See merge request !192
New makefile component_wrapper.mk allows some variables to be set
before component.mk is evaluated. This properly fixes problems with
sdkconfig being hard to access in all phases of the build.
Including component_common.mk is no longer necessary and will print a
deprecation warning for components which use it.
Reduces number of make invocations, allows variables exported in project
to be seen in all component make processes, not just the main ones.
Also makes a no-op build about 3x faster than it was.
esp32/make: add detailed return error code for wifi APIs
1. Add detailed return error code for wifi APIs
2. Add description about error code in esp_wifi.h
3. Modify esp_wifi_reg_rxcb to esp_wifi_internal_reg_rxcb
4. Modify esp_wifi_set_sta_ip to esp_wifi_internal_set_sta_ip
5. Mark system_init as deprecated API
See merge request !187
1. Add detailed return error code for wifi APIs
2. Add description about error code in esp_wifi.h
3. Modify esp_wifi_reg_rxcb to esp_wifi_internal_reg_rxcb
4. Modify esp_wifi_set_sta_ip to esp_wifi_internal_set_sta_ip
5. Mark system_init as deprecated API
wpa_supplicant: replace pre-built crypto library with source code
This change replaces libcrypto.a pre-built library with source code from wpa_supplicant.
For now i've decided to keep the modified layout of source and header files which is used in the esp32_rtos_sdk_core project. This will make it easier to move other parts of wpa_supplicant from esp32_rtos_sdk_core into esp-idf. Once we move everything, we can rearrange the files and upgrade wpa_supplicant to latest version.
See merge request !177
Deep sleep: Any source named rtc_wake_stub* is linked as RTC wake stub code
Also move esp_deepsleep.h documentation out to docs/deep-sleep-stub.rst
See merge request !142
146f5962 - Make the return value of esp_wifi_internal_tx consistent with LWIP error code so that
the up-layer can detect the out-of-memory error and take action accordingly, such do flow control.
Add cross-core int to accelerate task being awoken from another CPU.
This adds a per-CPU interrupt that can be used to poke the CPU to go do something. In this case all that is implemented is a request to yield the current task, used in case a CPU unblocks a task that runs on another CPU. This gets rid of the limitation that inter-CPU communication using queues, muxes etc can take up to a FreeRTOS tick to happen.
Specs!
Sending an in in a queue of length 1 (essentially a semaphore) as quickly as possible (just a small delay in the sender, to make sure the receiver task gets swapped out) for 10 seconds. Number indicates the amount of ints transferred
Old code:
CPU0->CPU0: 42986
CPU0->CPU1,: 2999
New code:
CPU0->CPU0: 42868
CPU0->CPU1: 62073
See merge request !155
- spaces->tabs in tasks.c
- update vfs_uart.c to use per-UART locks
- add license to vfs_uart.c
- allocate separate streams for stdout, stdin, stderr, so that they can be independently reassigned
- fix build system test failure
- use posix off_t instead of newlib internal _off_t
- spaces->tabs in tasks.c
- update vfs_uart.c to use per-UART locks
- add license to vfs_uart.c
- allocate separate streams for stdout, stdin, stderr, so that they can be independently reassigned
- fix build system test failure
Feature/wdts
This adds two watchdogs to esp-idf:
- An interrupt watchdog. Kicks in if the FreeRTOS timer interupt on either the PRO_CPU or (when configured) the APP CPU isn't called for a configurable time. Panics, displaying which CPU caused the problem and the registers that may lead to the offending code.
- A task watchdog. A task has to feed it every once in a while. If not, it will print the name of the offending tasks, as well as the tasks currently running on both CPUs, and optionally panic.
Also adds a panic reason to the panic call, as well as fixes the panic code a bit.
See merge request !148
The customers need to get information about AP that associated with ESP32 station,
these information includes RSSI, channel number etc, so add this new API
1. Modify sta to station in comments
2. Modify esp_wifi_get_ap_num to esp_wifi_scan_get_ap_num
3. Modify esp_wifi_get_ap_list to esp_wifi_scan_get_ap_records
1. Modify comments for esp_wifi_internal_tx
2. Fix delay time error in esp32_tx_flow_ctrl which is found in code review,
modify _wait_delay init value from 0 to 1
6ce01d76: rename some wifi internal APIs
aa4d2aa9: last rx buffer is reserved for mgmt frame
bb0ff4a8: tw7775 fix assert when rx auth frame before create bss
Feature/trax
Add Trax support to esp-idf. OpenOCD already has trax support, this allows an esp-idf program to also trigger this when needed. Also included: some more logic to correctly reserve memory blocks for Trax.
See merge request !73
Some small fixes
- Kill unused uxReturn in task.c, https://github.com/espressif/esp-idf/issues/48
- Line end conversion in gpio.c
- Move heap_alloc_caps.h so components can also use it
See merge request !135
lwip/esp32: support iperf
1. Add _exit() definition in syscalls.c
2. Fix a bug in sockets.c on which iperf depends
I'm now investigating performance of esp32, need iperf to be merged in to master branch for convience
See merge request !136
1. add libphy.a librtc.a, but store in bt submodule, if someone use them, please copy to esp32/lib/ instead the origin one
2. add 07_blufi demo
3. change esp32/Kconfig to allow bt/wifi coexist
esp32: Bootloader wake deep sleep stub
App can contain a stub program resident in RTC fast memory. Bootloader
will load the stub on initial boot. If the device wakes from deep sleep,
the stub is run immediately (before any other data is loaded, etc.)
To implement a custom wake stub, implement a function in your program:
```
void RTC_IRAM_ATTR esp_wake_deep_sleep(void)
{
esp_default_wake_deep_sleep();
// other wake logic
}
```
... and it will replace the default implementation.
See merge request !78
We reserve 4KB Slow RTC memory to save RF calibation result and BT NVS data.
If not all these Slow RTC momory Blocks are used, we will open the other parts.
App can contain a stub program resident in RTC fast memory. Bootloader
will load the stub on initial boot. If the device wakes from deep sleep,
the stub is run immediately (before any other data is loaded, etc.)
To implement a custom wake stub, implement a function in your program:
```
void RTC_IRAM_ATTR esp_wake_deep_sleep(void)
{
esp_default_wake_deep_sleep();
// other wake logic
}
```
... and it will replace the default implementation.
* master:
app_main: Return type to void
wifi: move type definitions into separate header file
wifi: use default esp_event_send handler in WIFI_INIT_CONFIG_DEFAULT
nvs: Remove flash layout arguments from nvs_init()
Add contributor agreement, update CONTRIBUTING file
Update http_request & https_request examples for new startup flow
Add very simple "hello world" & "blink" examples
Build examples out-of-tree as part of CI process
Examples: Use event groups for waiting until WiFi is associated & ESP has IP
BT example: Enable BT stack in config by default
BT: Relink component on new BT library, auto-initialise submodule if missing
Documentation: Add contributor guide, expand README & add an examples README
Update gitignore for examples
examples: Add https_request example
mbedtls: Add some initial menuconfig options
examples: HTTP request example
component/esp32: udpate wifi lib
component/esp32: modify bool argument name from enable to en
component/esp32: adjust some APIs
esptool: Bump upstream revision
* master: (32 commits)
components/nghttp: rename Makefile to component.mk
components/nghttp: add HTTP2.0 protocol feature
compoenents/esp32: don't alias start_cpu1 to start_cpu0_default
components/freertos: fix a bug with an uninitialised return value
Change application entry point name back to app_main
gitlab-ci: build SSC with matching branch name, if available
components/spi_flash: remove stray level of indentation
components/nvs: fix broken sentences in comment blocks
components/esp32: fix renaming of esp_event_set_cb, minor clean up
components/esp32: remove "_user" part from entry points, weaken start_cpu0/1
Fix a spelling mistake in panic message, add carriage return to stack canary message
components/lwip,esp32: fixes for C++
components/bt: fix compilation, remove ./ from makefile
components/esp32: clarify type of queue in wifi_init_config_t, add default init macro
components/esp32: add ESP_ERROR_CHECK
Event handling refactoring
clean up warnings
components/esp32,bt: fix typos in comments
Startup flow refactoring
Roll back submodule version
...
While this may reduce esp_wifi.h file readability for people who don't have a "go to definition" function in their editors, this is needed to decouple esp_wifi and esp_event headers, and possibly other headers which may use wifi types in the future.
* master:
components/spi_flash: remove stray level of indentation
components/nvs: fix broken sentences in comment blocks
Roll back submodule version
Spinlocks already come initialized. Remove the code that would essentially re-initialize them at runtime
Remove all references to prvLockQueue / prvUnlockQueue
components/esp32: clean up unused function warnings in single core mode
clean up warnings
components/nvs: fix build, use log library instead of printf
components/spi_flash: add flash operation counters option to Kconfig
components/nvs: add erase function
components/nvs: fix formatting
components/nvs: batch writes when possible
components/spi_flash: add performance counters
components/nvs: maintain item hash list at page level
components/nvs: avoid reading just-erased page
# Conflicts:
# components/esp32/cpu_start.c
# components/esp32/event_default_handlers.c
Clean up warnings and remove unused parts of FreeRTOS
For third party components (lwip and expat), compilation flags are adjusted to silence existing warnings (i have manually checked that all warnings are benign).
In components/esp32, replaced use of WIFI_DEBUG with ESP_LOG functions.
Additionally prvLockQueue/prvUnlockQueue have been removed, dragging some other bits of FreeRTOS along.
Original issue: https://github.com/espressif/esp-idf/issues/18
See merge request !111
- put contents of a few headers into c++ guard blocks
- fix off-by-one error in do_global_ctors
- remove system_init from startup code (should be called from main)
This change separates definitions in esp_event.h and functions in event.c into several parts:
- event structure definitions (esp_event.h)
- default implementations of event handlers (event_default_handlers.c)
- default implementation of event loop (event_loop.c, esp_event_loop.h)
Purpose of this change is to allow applications choose their own poison:
- full control of event loop at the expense of more bootstrap code
- pre-defined event task firing event callbacks, but less code in app_main.c
For third party components (lwip and expat), compilation flags are adjusted to silence existing warnings (i have manually checked that all warnings are benign).
In components/esp32, replaced use of WIFI_DEBUG with ESP_LOG functions.
Only remaining warning is in FreeRTOS queue.c, and it may be a useful one.
This change removes implicit WiFi/BT initialization from startup code.
"main" task is started once essential part of startup code is complete.
This task calls application-provided "int main(void)" function, which can call WiFi/BT init functions if necessary.
For third party components (lwip and expat), compilation flags are adjusted to silence existing warnings (i have manually checked that all warnings are benign).
In components/esp32, replaced use of WIFI_DEBUG with ESP_LOG functions.
Only remaining warning is in FreeRTOS queue.c, and it may be a useful one.
* master: (57 commits)
components/lwip: fix grammar
components/lwip: make SO_REUSE configurable via menuconfig
bootloader: remove trailing newlines from log messages
components/freertos: override per-task __cleanup handler to close stdin, stdout, stderr
components/esp32: move peripheral symbols to separate ld script
components/log: regroup macros for better readability
gitlab-ci: allow running tests for branches, triggered via API
components/log: fix timestamp calculation
components/log: set default runtime log level to ESP_LOG_VERBOSE
components/log: fix error when using ESP_LOGx from C++ code
components/log: fix bugs, add options to override log level for files, components, and bootloader
fix ledc and spi typo
remove prefix and postfix
Enable SO_REUSEADDR in LWIP
freertos: fix memory debug macro issue Define configENABLE_MEMORY_DEBUG according to CONFIG_ENABLE_MEMORY_DEBUG
peripheral structure headers: move volatile keyword from members to typedef
Adding -fstrict-volatile-bitfields to the CFLAGS/CXXFLAGS. Without this, gcc tries to access bitfields using the smallest possible methods (eg l8i to grab an 8-bit field from a 32-bit). Our hardware does not like that. This flag tells gcc that if a bitfield is volatile, it should always use the type the field is defined at (uint32_t in our case) to size its access to the field. This fixes accessing the hardware through the xxx_struct.h headers.
add peripheral module struct headers
build system docs: Add note about no spaces in component names
Docs: Add note about unusual submodule messages when cloning on Windows
...
# Conflicts:
# components/esp32/cpu_start.c
# components/esp32/include/soc/cpu.h
Add logging library
Logging library, intended to be used across other components.
Uses design similar to Android NDK logging APIs and allows for both compile time and run time filters, similar to logcat.
Also includes cleanup of cpu_startup.c — i was changing some logging output in this file so decided to re-format it and reduce code duplication.
Ref TW6703
See merge request !68
