esp_hw_support: Adds APIs to define user own MAC addresses without generation from the base MAC address
Closes IDFGH-5534 and IDFGH-8022
See merge request espressif/esp-idf!21036
- Remove esp_cpu_in_ocd_mode() from esp_cpu.h. Users should call esp_cpu_dbgr_is_attached() instead.
- Remove esp_cpu_get_ccount() from esp_cpu.h. Users should call esp_cpu_get_cycle_count() instead.
- Remove esp_cpu_set_ccount() from esp_cpu.h. Users should call esp_cpu_set_cycle_count() instead.
- Other IDF components updated to call esp_cpu_dbgr_is_attached(), esp_cpu_get_cycle_count() and esp_cpu_set_cycle_count() as well.
This commit marks all functions in interrupt_controller_hal.h, cpu_ll.h and cpu_hal.h as deprecated.
Users should use functions from esp_cpu.h instead.
The following two functions in bootloader_support are private now:
* esp_secure_boot_verify_sbv2_signature_block()
* esp_secure_boot_verify_rsa_signature_block()
They have been moved into private header files
inside bootloader_private/
* Removed bootloader_reset_reason.h and
bootloader_common_get_reset_reason() completely.
Alternative in ROM component is available.
* made esp_efuse.h independent of target-specific rom header
Some esp32c2 boards will be produced with a 26 MHz XTAL. This commit
adds the basic Kconfig option for this type of hardware.
Support for CONFIG_ESP32C2_XTAL_FREQ_26 in other areas of IDF will be
implemented in subsequent commits.
Some of the Memory Protection (internal) API functions dealing with per-CPU operations were missing appropriate handling of the CPU count actually configured by CONFIG_FREERTOS_UNICORE. The flaw was fixed across all the places found in the code as the issue was of general type
When creating G0 layer, some regi2c_*.h headers were moved out from
esp_hw_support (G1) to soc (G0). In order to be consistent with that change,
move all the remaining regi2c_*.h headers to soc too.
This commit updates the esp_cpu.h API. The new API presents a new
abstraction of the CPU where CPU presents the following interfaces:
- CPU Control (to stall/unstall/reset the CPU)
- CPU Registers (to read registers commonly used in SW such as SP, PC)
- CPU Interrupts (to inquire/allocate/control the CPUs 32 interrupts)
- Memory Port (to configure the CPU's memory bus for memory protection)
- Debugging (to configure/control the CPU's debugging port)
Note: Also added FORCE_INLINE_ATTR to the DoxyFile in order to pass doc
builds for esp_cpu.h
ESP32C3/ESP32S3: Fix cpu crash bug when wakeup from lightsleep for memory data miss
Closes IDF-162 and IDF-4923
See merge request espressif/esp-idf!17823
When enable sleep reject before this fix, we have two limitations:
1. it must be light sleep
2. RTC GPIO wakeup source must be set
We require light sleep because `esp_deep_sleep_start` function has
been declared with "noreturn" attribute, So developers don't expect
that this function may return (due to an error or a sleep reject).
But the requirement for RTC GPIO wakeup source is not reasonable for
all chips. This requirement exists because ESP32 only supports RTC GPIO
and SDIO sleep reject sources. But later chips support all sleep reject
sources.
This fix brings the following changes:
for ESP32: RTC GPIO and SDIO sleep reject sources can be enabled
when corresponding wakeup source is set.
for later chips: all sleep reject sources can be enabled when
corresponding wakeup source is set.
introduced in e44ead5356
1. The int8M power domain config by default is PD. While LEDC is using
RTC8M as clock source, this power domain will be kept on.
But when 8MD256 is used as RTC clock source, the power domain should
also be kept on.
On ESP32, there was protection for it, but broken by commit
e44ead5356. Currently the power domain
will be forced on when LEDC is using RTC8M as clock source &&
!int8m_pd_en (user enable ESP_PDP_DOMAIN_RTC8M in lightsleep). Otherwise
the power domain will be powered off, regardless of RTC clock source.
In other words, int8M domain will be forced off (even when 8MD256
used as RTC clock source) if LEDC not using RTC8M as clock source, user
doesn't enable ESP_PDP_DOMAIN_RTC8M, or in deep sleep.
On later chips, there's no such protection, so 8MD256 could't be used as
RTC clock source in sleep modes.
This commit adds protection of 8MD256 clock to other chips. Fixes the
incorrect protection logic overriding on ESP32. Now the power domain
will be determiend by the logic below (order by priority):
1. When RTC clock source uses 8MD256, power up
2. When LEDC uses RTC8M clock source, power up
3. In deepsleep, power down
4. Otherwise determined by user config of ESP_PDP_DOMAIN_RTC8M,
power down by default. (This is preferred to have highest
priority, but it's kept as is because of current code structure.)
2. Before, after the macro `RTC_SLEEP_CONFIG_DEFAULT` decides dbias, the
protection above may force the int8m PU. This may cause the inconsistent
of dbias and the int8m PU status.
This commit lifts the logic of pd int8m/xtal fpu logic to upper layer
(sleep_modes.c).
Related: https://github.com/espressif/esp-idf/issues/8007, https://github.com/espressif/esp-idf/pull/8089
temp
