ESP32 V1 and V2 - protection bits.
ESP32xx V2: revoke bits, protection bits
- refactor efuse component
- adds some APIs for esp32 chips as well as for esp32xx chips
- Cmake shows an error if the partition table has a test app.
- BOOTLOADER_APP_TEST depends on !BOOTLOADER_APP_ANTI_ROLLBACK.
- Bootloader does not boot the test app if secure version is low.
Closes: https://www.esp32.com/viewtopic.php?f=13&t=19164&p=71302#p71302
Since idf_monitor decodes anything that looks like a code address and
starts with 0x, bootloader logs often get annotated with function
names such as WindowOverflow and other random and scary looking things
unrelated to the issue the user is facing. Print the addresses without
0x to avoid confusion by decoded function names. Print hexadecimal
size with 'h' suffix to distinguish it from the decimal value that
follows.
* Target components pull in xtensa component directly
* Use CPU HAL where applicable
* Remove unnecessary xtensa headers
* Compilation changes necessary to support non-xtensa gcc types (ie int32_t/uint32_t is no
longer signed/unsigned int).
Changes come from internal branch commit a6723fc
During HAL layer refactoring and new chip bringup, we have several
caps.h for each part, to reduce the conflicts to minimum. But this is
The capabilities headers will be relataive stable once completely
written (maybe after the featues are supported by drivers).
Now ESP32 and ESP32-S2 drivers are relative stable, making it a good
time to combine all these caps.h into one soc_caps.h
This cleanup also move HAL config and pin config into separated files,
to make the responsibilities of these headers more clear. This is
helpful for the stabilities of soc_caps.h because we want to make it
public some day.
For getting secure_version field in anti rollback case, bootloader tries
to map whole firmware partition but fails for cases where partition size
is beyond available MMU free pages capacity.
Fix here insures to map only required length upto application descriptor
size in firmware partition.
Closes https://github.com/espressif/esp-idf/issues/5911
1. The 2nd bootloader always call `rom_spiflash_unlock()`, but never help to clear the WEL bit when exit. This may cause system unstability.
This commit helps to clear WEL when flash configuration is done.
**RISK:** When the app starts, it didn't have to clear the WEL before it actually write/erase. But now the very first write/erase operation should be done after a WEL clear. Though the risk is little (all the following write/erase also need to clear the WEL), we still have to test this carefully, especially for those functions used by the OTA.
2. The `rom_spiflash_unlock()` function in the patch of ESP32 may (1) trigger the QPI, (2) clear the QE or (3) fail to unlock the ISSI chips.
Status register bitmap of ISSI chip and GD chip:
| SR | ISSI | GD25LQ32C |
| -- | ---- | --------- |
| 0 | WIP | WIP |
| 1 | WEL | WEL |
| 2 | BP0 | BP0 |
| 3 | BP1 | BP1 |
| 4 | BP2 | BP2 |
| 5 | BP3 | BP3 |
| 6 | QE | BP4 |
| 7 | SRWD | SRP0 |
| 8 | | SRP1 |
| 9 | | QE |
| 10 | | SUS2 |
| 11 | | LB1 |
| 12 | | LB2 |
| 13 | | LB3 |
| 14 | | CMP |
| 15 | | SUS1 |
QE bit of other chips are at the bit 9 of the status register (i.e. bit 1 of SR2), which should be read by RDSR2 command.
However, the RDSR2 (35H, Read Status 2) command for chip of other vendors happens to be the QIOEN (Enter QPI mode) command of ISSI chips. When the `rom_spiflash_unlock()` function trys to read SR2, it may trigger the QPI of ISSI chips.
Moreover, when `rom_spiflash_unlock()` try to clear the BP4 bit in the status register, QE (bit 6) of ISSI chip may be cleared by accident. Or if the ISSI chip doesn't accept WRSR command with argument of two bytes (since it only have status register of one byte), it may fail to clear the other protect bits (BP0~BP3) as expected.
This commit makes the `rom_spiflash_unlock()` check whether the vendor is issi. if so, `rom_spiflash_unlock()` only send RDSR to read the status register, send WRSR with only 1 byte argument, and also avoid clearing the QE bit (bit 6).
3. `rom_spiflash_unlock()` always send WRSR command to clear protection bits even when there is no protection bit active. And the execution of clearing status registers, which takes about 700us, will also happen even when there's no bits cleared.
This commit skips the clearing of status register if there is no protection bits active.
Also move the execute_flash_command to be a bootloader API; move
implementation of spi_flash_wrap_set to the bootloader
Summary of changes:
- bootloader_clock split into *_clock_init and *_clock_loader.
Only esp_clk_apb_freq is in *_clock_loader.
- bootloader_common moved out of loader; functions needed in loader
(or, referenced from bootloader_utility) were moved into
bootloader_common_loader.c.
- assert and abort moved into bootloader_panic, made part of the
loader
- rtc_clk and rtc_time made part of loader
* changing dependencies from unity->cmock
* added component.mk and Makefile.projbuild
* ignore test dir in gen_esp_err_to_name.py
* added some brief introduction of CMock in IDF
Sometimes the flash size read from bootloader is not correct. This may
forbid SPI Flash driver from reading the the area larger than the size
in bootloader header.
When the new config option is enabled, the latest configured
ESPTOOLPY_FLAHSIZE in the app header will be used to override the value
read from bootloader header.
bootloader_support: Fix bootloader_common_get_sha256_of_partition(), can handle a long image
Closes IDFGH-3594
See merge request espressif/esp-idf!9509
Allows booting in QIO/QOUT mode or with PSRAM on ESP32-PICO-V3 and
ESP32-PICO-V3-O2 without any config changes.
Custom WP pins (needed for fully custom circuit boards) should still be compatible.
esp32/esp32s2: Reduce using ESP_EARLY_LOGx and move some code after the stdout initialization in startup code
Closes IDFGH-3367
See merge request espressif/esp-idf!8904
Reduces write cycles, and useful on ESP32 ECO3 as UART_DIS_DL is protected by
the same efuse.
Also fixes accidental macro definition introduced in 7635dce502
flash_encryption: modify additional efuses burning method to fix them are not being written
flass_encryption: burn efuse to disable boot from RAM space
flash_encryption: added better checking for key generation state plus set read and write protect for them
soc esp32s2: Add register-level bit definitions for read & wrote protect bits
esp32s2: Fixes for flash encryption
- Write efuses in a batch
- Fix some detection of whether existing efuse blocks are read/write protected
flash_enctryption: enabled flash encryption example on esp32s2
bootloader: raise WDT overflow value providing sufficient interval to encrypt app partition
flash_ encrypt: Fixed the TODOs on flash encryption key generation for esp32s2
flash_encryption: added secure boot features to flash enctryption for esp32s2
bootloader: leave only esp32s2 compatible potentially insecure options on menuconfig.
flash_encryption: removed secure boot version 1 from esp32s2 encryption code
flash_encryption: added CONFIG_SECURE_FLASH_REQUIRE_ALREADY_ENABLED option for esp32s2
flash_encryption: fixed the count of left plaintext flash
flash_encryption: disable dcache and icache download when using encryption in release mode
flash_encryption: add cache potentally insecure options for s2 chips
flash_encryption: fixed bug which bricked some chips in relase mode
If BLK2 is empty then it's OK to continue with a warning (otherwise it may spook users into thinking
something this is wrong, but this is the expected workflow.)
If BLK2 is not empty and doesn't match then we need to fail because it won't be possible to
trust the signature.
Previous method was to write-protect this efuse, however on ECO3
the write protect field also covers the UART_DOWNLOAD_DIS efuse.
Doing it this way keeps the possibility of disabling UART download
mode, later.
This commit updates the watchdog timers (MWDT and RWDT)
in the following ways:
- Add seprate LL for MWDT and RWDT.
- Add a combined WDT HAL for all Watchdog Timers
- Update int_wdt.c and task_wdt.c to use WDT HAL
- Remove most dependencies on LL or direct register access
in other components. They will now use the WDT HAL
- Update use of watchdogs (including RTC WDT) in bootloader and
startup code to use the HAL layer.
In commit 02d2903e39, mbedtls was
updated to release v2.16.5, where it was made mandatory to initialize
mbedtls_ctr_drbg_context before using same. It was fixed in wpa supplicant
but missed out in secure boot v2 verification code. This commit
fixes that.
Goal is that multiple faults would be required to bypass a boot-time signature check.
- Also strengthens some address range checks for safe app memory addresses
- Change pre-enable logic to also check the bootloader signature before enabling SBV2 on ESP32
Add some additional checks for invalid sections:
- Sections only partially in DRAM or IRAM are invalid
- If a section is in D/IRAM, allow the possibility only some is in D/IRAM
- Only pass sections that are entirely in the same type of RTC memory region
On the ESP32S2, rtc_clk_cal(RTC_CAL_RTC_MUX) measures the frequency
of the 90kHz RTC clock regardless of the selected slow clock
frequency. Keep track which clock is selected and pass the argument
to rtc_clk_cal accordingly.
fix clock choices
update rtc 32k xtal code for s2
missed api in rtc.h
bootloader_clock: update for S2
1. use spi functions in rom
2. remove unnecessary GPIO configurations.
3. remove unnecessary dummy settings.
4. enable dummy out function
5. flash and psram have independent timing setting registers.
6. no need to set 1.9v for LDO in 80Mhz
7. set IO driver ability to 1 by default.
8. no need to use GPIO matrix on esp32s2, IO MUX is recommended
9. enable spi clock mode and IO mode settings
1. Delete bootloader_clock_get_rated_freq_mhz, esp32s2 do not need it right now
2. Remove bootloader_flash_gpio_config () because it has the same function as bootloader_flash_dummy_config
DISABLED_FOR_TARGETS macros are used
Partly revert "ci: disable unavailable tests for esp32s2beta"
This partly reverts commit 76a3a5fb48.
Partly revert "ci: disable UTs for esp32s2beta without runners"
This partly reverts commit eb158e9a22.
Partly revert "fix unit test and examples for s2beta"
This partly reverts commit 9baa7826be.
Partly revert "efuse: Add support for esp32s2beta"
This partly reverts commit db84ba868c.
* Don't bother checking the chip revision if it looks like the partition
doesn't really contain an app
* Don't print the "info" level about the revision & min revision unless
we're in the bootloader (otherwise it gets printed at random times
during the OTA process)
bootloader_random_enable() and bootloader_random_disable() functions
can be used in app.
This MR added the protection for shared CLK_EN and RST_EN registers.
and all ECDSA to be disabled if secure boot is not enabled
Previously if ECDSA disabled in config then secure_boot_signatures.c would
fail to build (whether or not secure boot was enabled).
To avoid breaking apps that might be using the signature scheme with custom OTA
without enabling secure boot signatures in config, this change just disables
this functionality if unavailable in mbedTLS config.
Possible fix for root cause of https://github.com/espressif/esp-idf/pull/3703
Commit 8cd04c80 has added a dependency of efuse component on
esp_clk_apb_freq, however there was no definition of this function in
the bootloader context.
Reported at https://esp32.com/viewtopic.php?f=13&t=12035
This saves time when waking up from deep sleep, but potentially decreases
the security of the system. If the application able to modify itself
(especially areas that are loaded into RAM) in flash while running
without crashing or is modifies the cached bits of information about
what was last booted from the bootloader, this could cause security
issues if the user does a "deep sleep reset" since the full validation
is skipped.
Signed-off-by: Tim Nordell <tim.nordell@nimbelink.com>
No need to take this step if we are not doing image validation. The
obfuscation only buys us a tiny bit of "security" anyways since the
main parts of flash are memory mapped, too. This saves a little bit of
wake-up time when waking up from deep sleep when the
BOOTLOADER_SKIP_VALIDATE_IN_DEEP_SLEEP option is set.
Signed-off-by: Tim Nordell <tim.nordell@nimbelink.com>
We fixed some flash bugs in bootloader, but for the users used the old
vrsion bootloader, they can not fix these bugs via OTA, the solution is
add these updates in app startup.
These updates include:
1. SPI flash gpio matrix and drive strength configuration
2. SPI flash clock configuration
3. SPI flash read dummy configuration
4. SPI flash cs timing configuration
5. Update flash id of g_rom_flashchip
Made MMU pages available check in `esp_image_format.c`
This now makes it possible to map and process bootoader image as well in chunks when image doesn't fit completely into available free pages.
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
Do not include bootloader in flash target when secure boot is enabled.
Emit signing warning on all cases where signed apps are enabled (secure
boot and signed images)
Follow convention of capital letters for SECURE_BOOT_SIGNING_KEY variable, since it is
relevant to other components, not just bootloader.
Pass signing key and verification key via config, not requiring
bootloader to know parent app dir.
Misc. variables name corrections
Bootloader build requires verification key to be embedded in the binary.
Under specific configs, this key is generated during build time from the
signing key. Move the key generation to after the component
registration, since non scriptable commands are used in the process
(during early expansion)
This MR improves existing flash encryption document to provide simplified steps
Adds two new modes for user: Development & Release
Adds a simple example
Supports encrypted write through make command
Do not include bootloader in flash target when secure boot is enabled.
Emit signing warning on all cases where signed apps are enabled (secure
boot and signed images)
Follow convention of capital letters for SECURE_BOOT_SIGNING_KEY
variable, since it is
relevant to other components, not just bootloader.
Pass signing key and verification key via config, not requiring
bootloader to know parent app dir.
Misc. variables name corrections
!4452 and !4897 made some ill-advised corrections to dependency info;
revert those in this MR. Handling pre-built binaries as imported
libraries is retained, however.
Still using ESP32_xxx prefix on all chips: CORE_DUMP, APP_TRACE
Still using the same config prefix and duplicate names in esp32 & esp32s2beta: SPIRAM, PM
For example, if a renamed option CONFIG_NEW is a bool with value "n", kconfiglib will not generate a define for it in the Kconfig file. The define (#define CONFIG_NEW 1) will only be generated if the option is "y" or "m".
However the compatibility definition was always generated: #define CONFIG_OLD CONFIG_NEW. This broke the #ifdef checks which depended on the old option names.
Using xxx_periph.h in whole IDF instead of xxx_reg.h, xxx_struct.h, xxx_channel.h ... .
Cleaned up header files from unnecessary headers (releated to soc/... headers).
When flash work in DIO Mode, in order to ensure the fast read mode of flash
is a fixed value, we merged the mode bits into address part, and the fast
read mode value is 0 (the default value).
Fixed the case when the first part of log was missed
this was happened when:
* CONFIG_CONSOLE_UART_CUSTOM option is selected (UART1)
* The selected CONSOLE_UART port is used also for the console component
* in code esp_restart() or abort() functions were called.
This MR removes the common dependency from every IDF components to the SOC component.
Currently, in the ``idf_functions.cmake`` script, we include the header path of SOC component by default for all components.
But for better code organization (or maybe also benifits to the compiling speed), we may remove the dependency to SOC components for most components except the driver and kernel related components.
In CMAKE, we have two kinds of header visibilities (set by include path visibility):
(Assume component A --(depends on)--> B, B is the current component)
1. public (``COMPONENT_ADD_INCLUDEDIRS``): means this path is visible to other depending components (A) (visible to A and B)
2. private (``COMPONENT_PRIV_INCLUDEDIRS``): means this path is only visible to source files inside the component (visible to B only)
and we have two kinds of depending ways:
(Assume component A --(depends on)--> B --(depends on)--> C, B is the current component)
1. public (```COMPONENT_REQUIRES```): means B can access to public include path of C. All other components rely on you (A) will also be available for the public headers. (visible to A, B)
2. private (``COMPONENT_PRIV_REQUIRES``): means B can access to public include path of C, but don't propagate this relation to other components (A). (visible to B)
1. remove the common requirement in ``idf_functions.cmake``, this makes the SOC components invisible to all other components by default.
2. if a component (for example, DRIVER) really needs the dependency to SOC, add a private dependency to SOC for it.
3. some other components that don't really depends on the SOC may still meet some errors saying "can't find header soc/...", this is because it's depended component (DRIVER) incorrectly include the header of SOC in its public headers. Moving all this kind of #include into source files, or private headers
4. Fix the include requirements for some file which miss sufficient #include directives. (Previously they include some headers by the long long long header include link)
This is a breaking change. Previous code may depends on the long include chain.
You may need to include the following headers for some files after this commit:
- soc/soc.h
- soc/soc_memory_layout.h
- driver/gpio.h
- esp_sleep.h
The major broken include chain includes:
1. esp_system.h no longer includes esp_sleep.h. The latter includes driver/gpio.h and driver/touch_pad.h.
2. ets_sys.h no longer includes soc/soc.h
3. freertos/portmacro.h no longer includes soc/soc_memory_layout.h
some peripheral headers no longer includes their hw related headers, e.g. rom/gpio.h no longer includes soc/gpio_pins.h and soc/gpio_reg.h
BREAKING CHANGE
This prevents a device from being bricked in case when both secure boot & flash encryption are enabled and encryption gets interrupted during first boot. After interruption, all partitions on the device need to be reflashed (including the bootloader).
List of changes:
* Secure boot key generation and bootloader digest generation logic, implemented inside function esp_secure_boot_permanently_enable(), has been pulled out into new API esp_secure_boot_generate_digest(). The enabling of R/W protection of secure boot key on EFUSE still happens inside esp_secure_boot_permanently_enable()
* Now esp_secure_boot_permanently_enable() is called only after flash encryption process completes
* esp_secure_boot_generate_digest() is called before flash encryption process starts
1. separate rom include files and linkscript to esp_rom
2. modefiy "include rom/xxx.h" to "include esp32/rom/xxx.h"
3. Forward compatible
4. update mqtt
In the situation when bootloader was compiled for 240MHz, and app was
compiled for 160MHz, and the chip is a revision 0 chip, the
bootloader will assume that the application has also been running at
240MHz. This will cause the chip to lock up later. Modify this to use
a run time check of DPORT_CPUPERIOD_SEL, which indicates which of the
PLL frequencies was used.
Closes https://github.com/espressif/esp-idf/issues/2731.
Added:
* set a secure version in app/bootloader.
* description anti-rollback to ota part
* emulate the secure_version write and read operations
* efuse_em partition.
* a description about a rollback for native_ota_example.
Closes: TW26335
Bootloader used to calculate the number of cache pages assuming that
load address was aligned, while in reality load address for DROM and
IROM was offset by 0x20 bytes from the start of 64kB page. This
caused the bootloader to map one less page if the size of the image
was 0x4..0x1c less than a multiple of 64kB.
Reported in https://esp32.com/viewtopic.php?f=13&t=6952.
Added a new structure esp_app_desc_t. It has info about firmware:
version, secure_version, project_name, time/date build and IDF version.
Added the ability to add a custom structure with a description of the firmware.
The esp_app_desc_t is located in fixed place in start of ROM secotor. It is located after structures esp_image_header_t and esp_image_segment_header_t.
app_version is filed from PROJECT_VER variable (if set in custom make file) or PROJECT_PATH/version.txt or git repo (git describe).
Add API to get app_desc from partition.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
ROM definition of `abort` was removed in 9240bbb. The old definition
resulted in a panic due to a jump to a null pointer (abort member in
ROM stub table was zero). The new definition triggers a debug
exception if JTAG is connected, or goes into an infinite loop to be
reset by the WDT.
When CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled, RTC data is placed
into RTC_FAST memory region, viewed from the data bus. However the
bootloader was missing a check that this region should not be
overwritten after deep sleep, which caused .rtc.bss segment to loose
its contents after wakeup.
Allows OTA updates to be secured via signature checks, without requiring the overhead or complexity
of a full secure boot implementation.
Uses same signing mechanisms (build system and/or espsecure.py as Secure Boot).
Requires:
* [ ] More testing
* [ ] Documentation
Added bootloader_common_get_sha256_of_partition() and esp_partition_get_sha256() - get or calculate SHA-256
digest for app and data partitions.
Added bootloader_sha256_hex_to_str() - helps to print SHA-256 digest
Added esp_partition_check_identity() - compares two partitions by SHA-256 digest
Refactoring a function esp_image_load() in bootloader space to esp_image_verify() and
bootloader_load_image(). Old name function esp_image_load is deprecated
and will remove in V4.0 version.
spi_flash/sim: Fix error test_host. Add stub for bootloader_common_get_sha256_of_partition in sim/stubs
If we have the partition table without any ota_apps but in ota_data have
valide entry, in this case we get an error(hang). This commit fix this
case. If bs->app_count is zero when selecting the factory app.
Closes https://github.com/espressif/esp-idf/issues/2218
