1. When WIFI task or other high priority task blocks the Bluetooth task, ACL RX buffer will use up, ACL RX buffer ptr will point to null and will never point to a valid adress. Causing errors in Bluetooth.
2. hcimsgs.h used whether flow control is on or off
Problem Decribe
The problem happenned when do wps with a mikrotik router
1. router always want to do connect with 32 without EAP-WSC step
2. after 4 way timeour, 32 crash
Root Cause
The reason why can not start EAP-WSC step is router's check method is RSN > WPA > WPS, when it found there include RSN and WPS in assoc, it will choice do 4 way rather than WPS
The reason of second problem is 32's EAPOL start timer didn't stop and send EAPOL start to a null pointer
Soultion
1. remove RSN and WPA ie when do WPS step
2. check mac address's pointer before send EAPOL start
closes: https://github.com/espressif/esp-idf/issues/2382
Fix following WiFi bugs:
1. Fix the bug that MIC verification fails on soft-AP mode
2. Modify mesh root to have same behavior as normal WiFi STA in state change
3. Fix the bug that sniffer can't catch control packets
4. Fix crash bug in soft-AP mode
5. Fix ACM(Admission Control Management) bug
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
In earlier change this component was decoupled from freertos and hence
regression was introduced which changed default placement to flash. Some
device drivers make use of ringbuffer while flash cache is being disabled
and hence default placement should instead be internal memory.
Closes: https://github.com/espressif/esp-idf/issues/2517
1. fix some bugs by previous coex hw blocking bugfix,
such like, rwble.c (64, 0) line 222
2. fix bug that ble scan performance is very low when software coexist
is working.
3. update libcoexist version to v1.1.0
In some cases, when data was just written into UART FIFO, transmitter
state could be still zero while the FIFO did contain some data.
This resulted in uart_tx_wait_idle occasionally returning before all
the data was sent out.
Fix by checking both UART transmitter state and TX FIFO count.
1. Fix the bug that ESP32 will reject the retry AddBA request frame
if AddBA response frame is failed to sent by WiFi LMAC
2. Fix the bug that AddBA request retrys too frequently
3. Forbid BA session setup for VO queue related TID
1. remove use EID to distinguish psram voltage
2. 1V8 64Mbit psram and 3V3 64Mbit psram use the same psram driver(standard spi interface)
3. set cs hold time register as 1
In some cases, linker could choose to use ROM functions instead of the
ones defined in IDF.
For functions used in ROM stub table, this would lead to infinite
recursion when the corresponding function was called from ROM.
For crypto functions, some of these were modified in IDF, and
incompatible with ROM counterparts.
Problem Description
The reporduce steps are as follows:
1. put more than one same ssid AP in the environment;
2. set the STA mac address in one of the APs blacklist, and make sure the AP is closest to STA;
3. set the scan method in station config as all channel scan;
4. try to connect the AP which set STA in blacklist
Phenmenon
STA fail to connect after send auth or assoc with a wrong status code, but no disconnect event report and can not connect the next one in the envrionment
Root Cause
Because there are some same ssid APs in the evnrionment, when do all channel scan, it will collect all the matched AP in rc list, because rc list is not empty, so it would send disconnect event, however, we didn't do other step such as connect to other one
VNC MR 570
closes https://github.com/espressif/esp-idf/issues/2323
_rtc_data_{start,end} can now describe data placed into RTC_FAST
segment, if CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled.
Use new _rtc_slow_length symbol instead.
fix the bug following:
1. after disable bluetooth controller, wifi cannot TX/RX any packets.
2. when software coexist working, there's a little ratio cause wifi task watchdog timeout
3. when software coexist working, there's a little ratio cause bluetooth cannot receive anything.
feature:
1. add libbtdm_app.a git commit local and remote checking
Known issues:
1. there's still a bug occurs with a very very low ratio cause bluetooth
cannot receive anything. The reproduce interval may great than 3days ~ 1week via
7x24 hours heavy testing.
Previously, esp-touch only supports multicast packets which are
transmitted from cellphone. But for most dual frequency routers
whose SSIDs of 5G and 2.4G are the same, broadcast packets are
forwarded from 5G interface to 2.4G interface while multicast
packets are not. In order to make esp-touch work when cellphone
connects to 5G interface of these routers, esp-touch is improved
to support both multicast and broadcast packets. Meanwhile, new
APP which is compiled with Andriod or IOS library(>= v0.3.6.2)
must be used in this situation. Note that for some routers,
broadcast and multicast packets are forwarded from 5G interface
to 2.4G interface only when another WiFi device is connected to
2.4G interface of the router. Old APP which is compiled with
Android or IOS library(< v0.3.6.2) also works with this improvement
when cellphone connects to 2.4G interface of the router.
The Android and IOS library of new esp-touch APP is now available
on Github.
Android: https://github.com/EspressifApp/EsptouchForAndroid
IOS: https://github.com/EspressifApp/EsptouchForIOS
Four internal APIs `esp_http_client_connect()`, `http_client_prepare_first_line()`, `esp_http_client_request_send()` and
`esp_http_client_send_post_data()` API have been added for perfoming connection establishment (sync as well as async),
preparing first line, sending request and sending post data respectively.
In `transport_ssl`, `ssl_connect_async()` API has been added for establishing asynchronous connection.
1. suppport mesh type, mesh ID, router and IE crypt func&key at any time after mesh is initalized.
2. support modify parent at any time after mesh is configured.
3. modify manual networking example.
4. update header file.
5. fix issues in root conflicts handling.
6. add max length of beacon to menuconfig.
7. fix issue when received a beacon without DSSS.
Problem Description
set some of routers as the same ssid in the same channel, when 32 in the fast scan connect mode, there may no disconnect event report in that two sceanrio:
1. set the correct password and connect, if target router didn't report 32's auth req before timeout, the state machine change to init but no disconnect event report
2. set a wrong password, if router send disassoc or deauth after run, rather than wait 4 way handshake timeout, the state machine change to init but no disconnect event report
Root Cause
Because the routers are in the same channel, all of them are matched the ssid, so all of them can be instore in the rc list wait for connect, when the first one want to connect fail at auth or receive
disassoc or deauth when password wrong, the rc list is not empty, it can not send disconnect event because rc is not empty
Solution
1. put the fail the router in the blacklist
2. Judge whether there is another router can be connect, if it has, try to connect with the next one
VNC MR 561
gen_esp_err_to_name.py includes files like
components/lwip/include/apps/esp_ping.h as "apps/esp_ping.h" because all
subdirectories of "include" are used. If "components/lwip/include/apps"
is in the path of the compiler instead of "components/lwip/include" then
include "apps/esp_ping.h" will fail. This fix allows to process lines
like:
'// gen_esp_err_to_name.py: some text "esp_ping.h" some text'
in header files for overwriting the include.
Before LwIP was moved into a submodule, sntp and esp_ping were
available as the following includes:
#include "apps/sntp/sntp.h"
#include "esp_ping.h"
This commit makes header files available at the old location, and adds
a deprecation warning for sntp.h.
Closes https://github.com/espressif/esp-idf/issues/2392
If CONFIG_FREERTOS_LEGACY_HOOKS is kept enabled then defining
idle/tick hooks will be applications responsibility as was the
case earlier.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
1. Keep awake to receive beacon at TBTT time no matter which state
station is on.
2. If there is any packet to send on dream or sleep state, send NULL
data with power save bit clear first.
Changes:
KConfig: The option CONFIG_ESP32_RTCDATA_IN_FAST_MEM is added in Kconfig file for esp32 component.
esp32.common.ld: added support of RTC_DATA_ATTR, RTC_RODATA_ATTR data placement into appropriate segment according to Kconfig option.
esp32.ld: linker script is modified to set alias for memory segment selected by Kconfig option to place data. The segments for force placement are added for RTC_FAST_ATTR, RTC_SLOW_ATTR attributes.
esp_attr.h: added new attributes RTC_FAST_ATTR, RTC_SLOW_ATTR for force placement into fest/slow memory.
test_rtc_fast.c: Added unit test cases to check data placement into appropriate memory segment.
Updated documentation for RTC_DATA_ATTR, RTC_FAST_ATTR, RTC_SLOW_ATTR in deep_sleep_stub.rst file.
TW#18001
Closes https://github.com/espressif/esp-idf/issues/1553
The following commit rewrites the ESP-MESH docs. This commit includes
new diagrams and a structure approach to the mesh docs. Some mesh api references
have also been modified.
Some APs transmit AMPDU and MPDU by turns. Moreover, the sequence
numbers of AMPDU and MPDU are out of order, e.g. MPDU(1253) -
AMPDU(1251, 1252) - MPDU(1254) - AMPDU(1255, 1256). In order to
receive both AMPDU and MPDU in order, MPDU must be reordered with
AMPDU.
1. new APIs: esp_mesh_get_subnet_nodes_num() and esp_mesh_get_subnet_nodes_list().
2. fix hard to find the parent during connect.
3. disable Wi-Fi channel switch function.
4. fix a typo of MESH_EVENT_NO_PARENT_FOUND.
esp_reset_reason_init would check for reset reason hint, and
unconditionally set RTC_RESET_CAUSE_REG (which is also
RTC_ENTRY_ADDR_REG) to hint value 0, i.e. 0x80000000. However the ROM
code treats this value as valid deep sleep wake stub entry point, and
tries to jump to it.
Clear RTC_RESET_CAUSE_REG only if it contained a valid reset reason
hint, and simply set the register value to 0 when doing so. Also add
a check to esp_get_deep_sleep_wake_stub function that deep sleep wake
stub entry address must be in IRAM.
Reported in https://esp32.com/viewtopic.php?f=13&t=6919.
Fix following WiFi bugs:
1. Shouldn't scan when connect
2. Check beacon length in modem sleep
3. Fix the bug that AP may deauth wrong station when inactivity timer expires
4. Fix the bug that WiFi assert the system when receiving empty MCS in association response frame
When 32k XTAL was selected as clock source, if the first calibration
attempt failed, the code would fall back to 150kHz internal clock.
Calibration with the internal clock will always succeed.
Therefore `wait` would always be either 0 or 1. Based on this, some
code in this routine can be eliminated.
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
1. modify parent switch mechanism.
2. fix non-root doesn't clear the layer value in nvs.
3. fix retransmit the remove announcement packets.
4. add API esp_mesh_flush_upstream_packets().
5. automatically adjust passsive scan time based on the change of beacon interval.
No longer necessary to keep all reserved addresses in 'soc'.
Means 'soc' does not need to know about 'bt', for example.
Also means that Bluetooth can be enabled in config without any memory being reserved for BT
controller. Only if code calling the BT controller is linked in, will this memory be reserved...
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
Update libphy.a to v3960:
1. Decrease phy_init time from 900us to 347us in sleep wakeup
2. Fix RX STBC initialization
3. Modify set_chan function to fix interrupt watchdog issue
it will resolve the problem:
1. when bluetooth is running (For example: a2dp sink), wifi station cannot connect to AP easily
2. improve wifi connection success ratio when coexist is working
1. Modify esp_bt_controller_mem_release() to release BTDM BSS and Data to heap if
ESP_BT_MODE_BTDM mode is passed to it
2. Add a new API esp_bt_mem_release() which internally calls
esp_bt_controller_mem_release() with the provided mode and then if mode
is ESP_BT_MODE_BTDM, releases BT BSS and Data to heap.
Background:
For Wi-Fi and BT/BLE applications, for e.g. the usecase is like when
Bluetooth is used for provisioning and once the device is connected to the Wi-Fi
AP, we can turn off Bluetooth completely. In such scenarios, it should be possible to
reclaim all the memory of Bluetooth. Although, currently this does not
happen.
Experiment:
Made the following modifications to examples/bluetooth/gatt_server :
1. Added support of simple_wifi to it
2. Moved all the bluetooth related code under CONFIG_BT_ENABLED config
option
3. Calculated the free heap in 2 similar scenarios:
i. Disabled BT (CONFIG_BT_ENABLED undefined) and checked the free
heap after STA connected
ii. Kept BT enabled and disabled it after STA connected and checked
the free heap
Ideally, the numbers for i., ii. above should have been similar. But
there was a delta of almost 30-31K. (i. > ii.)
4. Through make size-components checked the common BSS for libbta.a and libbtdm_app.a
and found it to be almost 30K. Data is around 1K
Solution:
1. Modified the linker script to mark the BSS and Data for these libraries and
free it when ESP_BT_MODE_BTDM mode is passed to mem release APIs.
2. Verified that the free heap is comparable for i. and ii. above.
Note: It is known that once this is done, Bluetooth can only be used
again post reboot.
Signed-off-by: Hrishikesh Dhayagude <hrishi@espressif.com>
* Fixes some "noreturn" functions in bootloader utils which did return (causing fatal CPU
exceptions).
* Marks bootloader entry as "noreturn", preventing "user code done" from stalling boot
Partial fix for https://github.com/espressif/esp-idf/issues/1814 TW20016
(Comprehensive fix for this issue will be enabling WDT during bootloader, coming shortly.)
1. Move channel to the first row of the table.
2. Remove the condition of HT20/HT40 for they are determined by
secondary channel.
3. Clean up the CSI table.
Fixed the error division on zero.
Also fixed range CONFIG_ESP32_RTC_CLK_CAL_CYCLES in Kconfig.
Fixed a overflow error by TIMG in the function rtc_clk_cal_internal. This error was due to a limit in values TIMG_RTC_CALI_MAX=0x7FFF (to write the slowclk_cycles) and TIMG_RTC_CALI_VALUE=0x1FFFFFF (to read xtal_cycles). Added assert finctions.
Closes https://github.com/espressif/esp-idf/issues/2147
1. Add reading psram EID.
2. Configure different clock mode for different EID.
3. add API to get psram size and voltage.
4. Remove unnecessary VSPI claim.
For 32MBit@1.8V and 64MBit@3.3V psram, there should be 2 extra clock cycles after CS get high level.
For 64MBit@1.8 psram, we can just use standard SPI protocol to drive the psram. We also need to increase the HOLD time for CS in this case.
EID for psram:
32MBit 1.8v: 0x20
64MBit 1.8v: 0x26
64MBit 3.3v: 0x46
Since 94250e42a0, UART output is suspended when entering sleep mode
(deep or light sleep). This makes sense for light sleep, where sleep
normally takes small amount of time, and flushing the UART would add
a lot of latency. But this breaks existing behaviour for deep sleep,
where UART output was previously sent out before entering sleep mode.
Closes https://github.com/espressif/esp-idf/issues/2145
remote_ip was declared to be a pointer to an address that was
overwritten in later stage thus changing the address pointed by remote_ip
esp_smartconfig.h : Fixed a typo. station_config to wifi_config_t
Signed-off-by: Sachin Parekh <sachin.parekh@espressif.com>
components/esp32/ipc.c: In function 'esp_ipc_init':
components/esp32/ipc.c:82:31: error: '%d' directive writing between 1 and 11 bytes into a region of size 5 [-Werror=format-overflow=]
sprintf(task_name,"ipc%d",i);
^~
components/esp32/ipc.c:82:27: note: directive argument in the range [-2147483648, 1]
sprintf(task_name,"ipc%d",i);
^~~~~~~
components/esp32/ipc.c:82:9: note: 'sprintf' output between 5 and 15 bytes into a destination of size 8
sprintf(task_name,"ipc%d",i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
INTERRUPT and CCOUNT registers will change outside of program control.
Making the inline assembly used to read these registers volatile
indicates this fact to the compiler.
Fixes https://github.com/espressif/esp-idf/issues/2127
1. fix BLE connection missing in coex mode
2. modify other parameters to make coex priority more reasonable
3. fix modem sleep procedure trap cause Wifi disable RF when BT is
working. Such cause that BR/EDR is difficult to be connected, BLE
connection stability decrease and so on.
4. modify BR/EDR coexist duration to imrove BR/EDR connect success
ratio.
5. Due to the hardware coexist bug, BLE scan interval/window should
be less than 0x100(about 160ms). Therefore, it will cause BLE cannot
scan any advertising packet while WiFi have higher priority
behaviour(such like RX beacon, scan, TX/RX VO packets and etc.).
1. add APIs to set/get announce interval values.
2. add API to enable/disable the min rate to 6Mbps for data packages.
3. add APIs to set/get RSSI threshold values.
4. fix ap_loss.
Since commit 94250e4, EXT0 wakeup mechanism, when wakeup level was set
to 0, started waking up chip immediately after entering deep sleep.
This failure was triggered in that commit by a change of
RTC_CNTL_MIN_SLP_VAL (i.e. minimum time in sleep mode until wakeup
can happen) from 128 cycles to 2 cycles.
The reason for this behaviour is related to the way input enable (IE)
signal going into an RTC pad is obtained:
PAD_IE = (SLP_SEL) ? SLP_IE & CHIP_SLEEP : IE,
where SLP_IE, SLP_SEL, and IE are bits of an RTC_IO register related
to the given pad. CHIP_SLEEP is the signal indicating that chip has
entered sleep mode.
The code in prepare_ext{0,1}_wakeup did not enable IE, but did enable
SLP_SEL and SLP_IE. This meant that until CHIP_SLEEP went high, PAD_IE
was 0, hence the input from the pad read 0 even if external signal
was 1. CHIP_SLEEP went high on the 2nd cycle of sleep. So when
RTC_CNTL_MIN_SLP_VAL was set to 2, the input signal from the pad was
latched as 0 at the moment when CHIP_SLEEP went high, causing EXT0
wakeup with level 0 to trigger.
This commit changes the way PAD_IE is enabled: SLP_SEL and SLP_IE are
no longer used, and IE is set to 1. If EXT0 wakeup is used, RTC_IO is
not powered down, so IE signal stays 1 both before CHIP_SLEEP goes
high and after. If EXT1 wakeup is used, RTC_IO may be powered down.
However prepare_ext1_wakeup enables Hold on the pad, locking states
of all the control signals, including IE.
Closes https://github.com/espressif/esp-idf/issues/1931
Closes https://github.com/espressif/esp-idf/issues/2043
Previously the loop in esp_timer_impl_set_alarm was necessary to catch
the case when timer count wraps around (goes from 2^32 - 1 to 0).
Since ALARM_OVERFLOW_VAL was reduced from 2^32 - 1 to 0xefffffff,
this is no longer necessary.
Fixes https://github.com/espressif/esp-idf/issues/1891
Allows you to move the partition table, it gives more space for the bootloader.
Added a new utility - parttool.py. This utility can search for the offset and/or size of the partitions by name and type/subtype. Use for getting APP_OFFSET and PHY_DATA_OFFSET.
The linker(esp32.bootloader.ld) made changes that allow you to write a custom bootloader code more.
TW14125
Before entering the deep sleep, the RTC and FRC counters are synchronized. Updating the boot_time.
Added a unit test for this case.
Fixed warnings for MULTIPLE_STAGES
Closes https://github.com/espressif/esp-idf/issues/1840
1. Fix the WiFi/BT coexist bug
2. Fix WPA2 enterprise example crash bug
3. Add size and version check for crypto type struct
4. Add MD5 check for crypto type header file
1. add mesh_assoc_t to esp_mesh_internal.h file.
2. rename "node" to "device" in esp_mesh.h.
3. add MESH_EVENT_SCAN_DONE event.
4. add APIs esp_mesh_scan_get_ap_record() and esp_mesh_scan_get_ap_ie_len() to get scan results.
5. modify API esp_mesh_set_self_organized() by adding parameter "select_parent".
6. modify API esp_mesh_set_parent() by adding parameter "parent_mesh_id"
7. add manual networking example.
1. Store the calibration data to NVS if PHY does full calibration because of calibration data checksum failure
2. Pass the station's mac to PHY for checksum calculation
A new method of workaround an error with DPORT is to ensure that the APB is read and followed by the DPORT register without interruptions and pauses. This fix places this implementation in the IRAM to exclude errors associated with the cache miss.
Add error handling for http client
set ssid password correct with Example_WIFI test, and clear password before free
Fixed the CI failure due to HTTP errror names
1. provide options for bluetooth low power mode
2. provide two options for bluetooth low power clock: main XTAL and external 32kHz XTAL
3. provide function and callbacks to control bluetooth low power mode, including enable/disable sleep, software wakeup request, low power clock settings, check power state, etc
4. modify vhci API vhci_host_send_packet to use blocking mode
5. note that DFS and bluetooth modem sleep can not be used together currently.
Added .rtc_noinit and .noinit section definitions into linker file /esp32/ld/esp32.common.ld.
The macro __NOINIT_ATTR, RTC_NOINIT_ATTR declared in esp32/esp_attr.h file.
Added unit test file to test added behavior for noinit variables and its attributes.
Added documentation changes for new added attributes.
Make some corrections after code review:
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
The linker file has been corrected to place noinit section before bss_start to make it safer.
Documentation file has been modified to clarify reset behavior of allocated data .
Corrected typos in test_noinit.c and removed assertion of noinit variable to avoid possible issues with ROM boot loader memory allocation.
Update test_noinit.c file to address RTCWDT_RTC_RESET reset reason instead of POWERON_RESET.
Test optimized to pass automated unit testing.
esp32: Add .noinit and .rtc_noinit sections to the linker script
Update of general-notes.rst documentation to fomat examples as code and attributes as identifiers.
Test test_noinit.c corrected to pass automated testing (support ofTEST_CASE_MULTIPLE_STAGES())
https://ezredmine.espressif.cn:8765/issues/15878
1. remove rc when ap not found
closes issue: https://github.com/espressif/esp-idf/issues/1797
2. allocate mimo packet to internal memory
3. use FRC2 timer instead of WDEV_NOW() for modem sleep to calculate
TBTT time.
It fixes the bug that TBTT will be incorrect if beacon is lost.
If the RTC crystal is bad or has no matched capacitance, then you do not need to start such the crystal. It is necessary to determine this case, output an error (about impossibility to start from the oscillator) and start from the internal RC of the chain.
Reduced the default value of the number of bootstrap cycles. Because we can oscillating the oscillator which then stops. (in Kconfig). Changed from 100 to 5.
The number of calibration cycles has been increased. It is the main criterion for estimating the launch of an oscillator. A large increase leads to an increase in the load time, as well as the stability of recognition of this case. (in Kconfig).
Changed from 1024 to 3000.
When two CPUs read the area of the DPORT and the area of the APB, the result is corrupted for the CPU that read the APB area.
And another CPU has valid data.
The method of eliminating this error.
Before reading the registers of the DPORT, make a preliminary reading of the APB register.
In this case, the joint access of the two CPUs to the registers of the APB and the DPORT is successful.
If the allocated interrupt list is not empty and the new item will be inserted
as the header of the list, insert_vector_desc() causes crash because pre is
null. This commit fix this issue.
change some API function to throw event:
esp_wifi_deauth_sta
esp_wifi_get_country
esp_wifi_ap_get_sta_list
esp_wifi_sta_get_ap_info
esp_wifi_stop
esp_wifi_get_channel
esp_wifi_get_protocol
esp_wifi_get_bandwidth
When light sleep is started, the other CPU gets halted using DPORT
stall mechanism. This can happen while it is inside an esp_timer
critical section, which may lead to a deadlock. This change adds
functions to take and release esp_timer lock before entering
DPORT critical section, preventing the deadlock.
1. Add error log if failed to store calibration version/mac/data
2. Change the NVS calibration version/mac/data store sequence
3. Pass the init_data instead of NULL to esp_phy_rf_init() in esp_phy_load_cal_and_init()
* Philosophical: "explicit is better than implicit".
* Practical: Allows useful errors if invalid directories given in components as the defaults aren't
always used. Also trims the -I path from a number of components that have no actual include
directory.
* Simplifies knowing which components will be header-only and which won't
1. Bootloader reads SPI configuration from bin header, so that the burning configuration can be different with compiling configuration.
2. Psram mode init will overwrite original flash speed mode, so that users can change psram and flash speed after OTA. 3. Flash read mode(QIO/DIO…) will not be changed in app bin. It is decided by bootloader, OTA can not change this mode.
4. Add read flash ID function, and save flash ID in g_rom_flashchip
5. Set drive ability for all related GPIOs
6. Check raise VDDSDIO voltage in 80Mhz mode
7. Add check flash ID and update settings in bootloader
8. Read flash ID once and keep in global variable
9. Read flash image header once and reuse the result
Tested cases:
1. Test new and old version of bootloader
boot Flash 20M —> app Flash 80M + Psram 80M
boot Flash 40M —> app Flash 80M + Psram 80M
boot Flash 80M —> app Flash 80M + Psram 80M
boot Flash 20M —> app Flash 80M + Psram 40M
boot Flash 40M —> app Flash 80M + Psram 40M
boot Flash 80M —> app Flash 80M + Psram 40M
boot Flash 20M —> app Flash 40M + Psram 40M
boot Flash 40M —> app Flash 40M + Psram 40M
boot Flash 80M —> app Flash 40M + Psram 40M 2. Working after esp_restart reboot.
* Move smartconfig to its component directory, it should be possible to override
this as whole component
* Fix few header includes related to lwIP networking stack
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
1. fix issues on sending beacon caused by too much tx retries on other packets.
2. modify not to scan if rc exists when connect.
3. modify scan dwell time to default 120ms fo root.
1. fix a bug in initliazing map beacon interval.
2. fix not send MESH_EVENT_ROUTING_TABLE_REMOVE when MESH_NWK_CHILD_DISCONNECTED.
3. fix a bug in returning roots ie len.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
The get_time_ms() is updated to explicitly use fabs(dt) instead of abs(dt) in test_sleep.c.
Some other minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
It is not possible to generate 1 MHz REF_TICK from 2 MHz APB clock
(this is a limitation of REF_TICK divider circuit). Since switching
REF_TICK frequency is something we would like to avoid (to maintain
UART output even with DFS), 2 MHz frequency has been marked as
unsupported.
The issue would manifest itself in cases when switching from PM
configuration like {active=160MHz, idle=80MHz} to {active=80MHz,
idle=80Mhz}. After the configuration was changed, PM logic would
think that current frequency was 80MHz and would not do any further
switching. In fact, frequency was still 160MHz.
The old code calculated MAX() of two enum values, but CPU frequency
enum values are not ordered (2MHz goes after 240MHz). This caused
incorrect configuration to be set.
1. External 32kHz crystal is started for too long or it may not start at all. It is often observed at the first start.
2. At the first start, it is possible that the crystal did not start. And the recorded period was recorded as 0. Which led to a division error by zero during the transition to the deep sleep mode (Maybe somewhere else).
3. Added a unit test to test a new method of oscillation an external crystal.
4. Added a new method of oscillating of an external crystal. The legs of the crystal are fed with a 32 kHz frequency.
The new method eliminates these errors.
Added unit test: `\esp-idf\components\soc\esp32\test\test_rtc_clk.c`: `make TEST_COMPONENTS=soc`
- 8 Test starting external RTC crystal. Will pass.
`Bootstrap cycles for external 32kHz crystal` - is specified in the file Kconfig by default 100.
QA tested a new method of oscillation the crystal on 25 boards. The supply of square waves on the crystal showed a 100% result in contrast to the previous method of launching the crystal. After the tests, the old method was deleted.
Closes TW19143
- separate mode stats from lock stats by an extra comment line
- add CPU frequency column to the mode stats
- don’t print a row for light sleep if light sleep is not enabled
s_cpu_freq_by_mode array was statically initialised with 80MHz CPU
frequency in CPU_MAX and APB_MAX modes, but sdkconfig setting for the
CPU frequency could have been different. For the case of 240MHz CPU
frequency, this would cause a frequency switch between 240MHz and
80MHz to happen, even though such switch is not supported in the fast
path switching functions used by the DFS implementation.
This fixes the issue by moving initialisation into esp_pm_impl_init,
which is called at startup before the first mode switch can happen.
Fixes https://github.com/espressif/esp-idf/issues/1729.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
The timer wakeup function once activated cannot be disabled later using existing api. If user wants to use different wakeup sources after first sleep but it does not work. This change disables timer wakeup trigger in configuration that will be set into appropriate RTC registers in esp_light_sleep_start() function.
Added function esp_sleep_disable_wakeup_source() to deactivate wakeup trigger for selected source.
Updated documentation for this function in sleep_modes.rst file to pass make html.
Updated unit test to check this functionality for light sleep.
The test_sleep.c unit test is updated to add reliability for auto unit testing.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
tools/gen_esp_err_to_name.py generates
components/esp32/esp_err_to_name.c for lookup of the error codes from
all of the IDF project and easily identify all codes in one place
1. Put some lwip udp rx/tx relating functions to IRAM
2. Put some wifi rx/tx relating functions to IRAMa
3. Reduce wifi dynamic malloc from 4 to 1 for each ebuf
4. Update iperf example accordingly
5. Update libphy.a to v383
close github issue#1037 WiFi Promiscuous filter breaks w/
WIFI_PROMIS_FILTER_MASK_ALL and issue#1404
esp_wifi_set_promiscuous_filter set WIFI_PROMIS_FILTER_MASK_ALL error
When INT WDT fires, panicHandler is invoked. In OCD mode, panicHandler
sets a breakpoint on the PC from the exception frame and returns.
However in case of INT WDT, interrupt flag is still set in TIMERG1
peripheral, which causes INT WDT to trigger again. This causes an
endless stream of "Core 0 panic'ed (Interrupt wdt timeout on CPU1)"
messages. OpenOCD also gets terribly confused at this point.
Disable watchdogs when exiting panic handler in OCD mode.
Clear TIMERG1 WDT interrupt flag to prevent re-entry into panic handler.
libc time function now rely on esp_timer_get_time as the source of
high-resolution time, rather than FRC1 timer. Internally, on the ESP32
esp_timer implementation uses FRC2 timer.
- Change help text and labels in Kconfig to use "high-resolution timer"
instead of FRC1. Keep existing Kconfig option name to be backwards
compatible.
- Change references to "FRC1" in the source code to "FRC".
A function to change "in IRAM" status for an existing interrupt handle, without going through free/allocate of the interrupt.
mOS HW timer implementation requires this to make HW timers safe to re-set from an IRAM ISR.
1. Add a hide API for station to receive and process probe request
frame.
2. Fix an issue that wifi/bt coexistence crashes in PSRAM version.
3. Fix an issue that the API for clearing vendor ie can not work.
4. Fix an issue that wifi stop and reboot leads watchdog.
Timer callback can delete the timer. If CONFIG_ESP_TIMER_PROFILING was
enabled, this caused an access to invalid (freed) memory.
This fix adds a pointer to track the timer while executing the callback.
This is needed so that we can check if callback deletes the timer,
in which case we won't try updating profiling counters for this timer
after the callback is done.
Renamed the internal rc to __err_rc to avoid clashes with local variables.
This code would not do the expected thing with the original ESP_ERROR_CHECK macro:
esp_err_t my_func(esp_err_t x)
{
assert(x == 23);
}
esp_err_t rc = 23; //some value that is important fo the user
ESP_ERROR_CHECK(my_func(rc));
The macro will expand to:
esp_err_t rc = (my_func(rc));
And the code will assert, as my_func will receive a random value - whatever is in the internal macro rc temp variable. This is due to the C weirdness of allowing this code:
int x = x; //x has a random value.
This commit reverts the revert on the new task watchdog API. It also
fixes the following bug which caused the reversion.
- sdkconfig TASK_WDT_TIMEOUT_S has been reverted from the unit of ms back to the
unit of seconds. Fixes bug where projects using the new API without rebuilding sdkconfig
would cause the old default value of 5 to be interpreted in ms.
This commit also adds the following features to the task watchdog
- Updated idle hook registration to be compatible with dual core hooks
- Updated dual core hooks to support deregistration for cpu
- Legacy mode has been removed and esp_task_wdt_feed() is now replaced by
esp_task_wdt_reset(). esp_task_wdt_feed() is deprecated
- Idle hooks to reset are now registered/deregistered when the idle tasks are
added/deleted from the Task Watchdog instead of at Task Watchdog init/deinit
- Updated example
1. V366, fix a problem which initialize current can reach 800mA.
2. V365, fix a problem for pll_cap tracking in Coexist (BT & WIFI)
mode. The problem will make Coexist (BT & WIFI) WIFI AP mode TX
Fail in high temperature(>70).
3. V364, fix a bug of BT and Wifi coexist (hung in function of
force_wifi_mode())
1. move settings of WIFI_CLK_EN_REG for bluetooth into controller init/deinit APIs
2. modify the bit mask used in phy_rf init/deinit to use WIFI-BT shared bits
Previously esp_restart would stall the other CPU before enabling RTC_WDT.
If the other CPU was executing an s32c1i instruction, the lock signal
from CPU to the arbiter would still be held after CPU was stalled. If
the CPU running esp_restart would then try to access the same locked
memory pool, it would be stuck, because lock signal would never be
released.
With this change, esp_restart resets the other CPU before stalling it.
Ideally, we would want to reset the CPU and keep it in reset, but the
hardware doesn't have such feature for PRO_CPU (it is possible to hold
APP_CPU in reset using DPORT register). Given that ROM code will not use
s32c1i in the first few hundred cycles, doing reset and then stall seems
to be safe.
In addition to than, RTC_WDT initialization is moved to the beginning of
the function, to prevent possible lock-up if CPU stalling still has any
issue.
1. Fix WiFi timer enable twice issue
2. Fix a softAP compatibility issue
3. Fix ebuf alloc counter issue
4. remove nvs_flash_init() in esp_wifi_init()
5. Fix scan only find few APs after set bssid
6. Fix can not connect to hidden SoftAP
7. Remove group key entry before connecting ot AP
