xPendingReadyList[1] was never initialised correctly, so if a task is added to this list (ie by xSemaphoreGiveFromISR()
or similar) while scheduler is disabled, then it causes a null pointer dereference.
Bug produces stack traces similar to:
0x40086e87: vListInsertEnd at /home/gus/esp/32/idf/components/freertos/./list.c:130
0x40084ba3: xTaskRemoveFromEventList at /home/gus/esp/32/idf/components/freertos/./tasks.c:3439
0x40083c54: xQueueGiveFromISR at /home/gus/esp/32/idf/components/freertos/./queue.c:2034
0x400f50a0: timer_group0_isr at /home/gus/esp/32/idf/components/freertos/test/./test_suspend_scheduler.c:27
0x40081d7d: _xt_lowint1 at xtensa_vectors.o:?
Writing values longer than half of the page size (with header taken into
account) causes fragmentation issues. Previously it was suggested on the
forum that using long values may cause issues, but this wasn’t checked
in the library itself, and wasn’t documented. This change adds necessary
checks and introduces the new error code.
Documentation is also fixed to reflect the fact that the maximum length
of the key is 15 characters, not 16.
component/bt: squash the branch of the early commit
component/bt: Added the set static random address callback to the bt project.
component/bt: fixed the set static random address error.
component/bt: fixed the set static random address error.
To increase the chances that the examples work out of the box, this
change is raising the default deep sleep wakeup delay to 1ms.
If GPIO15 is low at startup, ROM code takes less time to execute
(because no logging is performed), so more time may be needed to allow
flash chip to become ready.
Triggered on make 3.81, happens sometimes on Linux and always(?) on macOS. May depend on the order the OS' filesystem
resolves wildcards in.
Includes a revert to the LWIP component to verify this is properly fixed.
See also https://github.com/espressif/esp-idf/issues/632
Fix Dport access in interrupts
Dport accesses would re-enable interrupts unconditionally, breaking things when called in an ISR. This saves and restores the interrupt status, fixing this.
This fixes a crash in the SPI slave driver, and possibly other things.
See merge request !772
CI: auto generate configs for test jobs
Currently CI test jobs are static configured by several pre-generated config files.
This approach have several disadvantages:
1. not flexible to select test cases to run, which is important feature of @bot
2. difficult to update test as we need to pre-generate quite a lot files
3. need to maintain extra config files in IDF
4. not flexible to support new test apps or chips, can't use some new features of test bench
Therefore we'll add assign_test stage between build and test, to generate configs for test jobs.
See merge request !738
Make internal stack size variables in FreeRTOS 32-bit instead of 16-bit
Stock FreeRTOS uses an uint16 to store stack sizes, making it impossible to allocate a stack >64K. This changes this into an uint32, allowing for larger stacks.
See merge request !677
Partition table gen esp32part fixes: App offset errors, Python 3 support
As mentioned on forums, gen_esp32part.py wasn't erroring correctly if a non-64KB-aligned app partition was referenced.
Also merges a PR to add Python 2&3 support (with some tweaks). Not very useful in IDF right now, but useful for Arduino.
See merge request !751
1. Name change from chopper to carrier, block diagram update, minor changes to example codes
2. mcpwm_reg.h changed, brought uniformity in comments, worked on suggestions, duty to accept float. Some name changes!
3. Minor readme changes and Indetation
4. Minor change: move mcpwm_reg.h and mcpwm_struct.h to new path
5. Minor change: addition of BLDC example code and Readme
6. Name changed from epwm to mcpwm
7. Improve the reg name in mcpwm_struct.h
8. Name change chopper>carrier, deadband>deadtime
component/bt: fix the exception in attp_buil_sr_msg when handling gatt write bug. bug number #12124.
fix the exception in attp_buil_sr_msg when handling gatt write bug.
See merge request !743
Small unit-test-related fixes
Fixes for some small bugs found running unit tests with heap poisoning turned on.
All are bugs in the tests, except for one FreeRTOS fix (when deleting a task, check if it's running on the other CPU and preempt it if so.)
See merge request !746
nvs: remove search cache at page level
Since read cache was introduced at page level, search cache became
useless in terms of reducing the number of flash read operations.
In addition to that, search cache used an assumption that if pointers to
keys are identical, the keys are also identical, which was proven wrong
by applications which generate key names dynamically.
This change removes CachedFindInfo, and all its uses. This is done at
expense of a small extra number of CPU operations (looking up a value in
the read cache is slightly more expensive) but no extra flash read
operations.
Ref TW12505
Ref https://github.com/espressif/arduino-esp32/issues/365
See merge request !753
Since read cache was introduced at page level, search cache became
useless in terms of reducing the number of flash read operations.
In addition to that, search cache used an assumption that if pointers to
keys are identical, the keys are also identical, which was proven wrong
by applications which generate key names dynamically.
This change removes CachedFindInfo, and all its uses. This is done at
expense of a small extra number of CPU operations (looking up a value in
the read cache is slightly more expensive) but no extra flash read
operations.
Ref TW12505
Ref https://github.com/espressif/arduino-esp32/issues/365
1. Enlarge wifi task stack size by 512Bytes to fix potential stack overflow issue
2. Modify wifi hmac tx queue size from 12 to 32 because we already limit the buffer number in ebuf
management module
add API to get chip info
This change adds an API to get chip info, such as chip model, enabled capabilities, size of embedded flash, silicon revision.
Hello_world example is modified to print out the information about the chip. The example is also simplified by moving all code into the main task.
Ref TW12031.
See merge request !549
esp32: update wifi lib for some bugfix
1. Fix wifi ebuf free twice issue
2. Fix wifi internal assert issue
3. Fix a bug in esp_wifi_stop
4. Fix wifi crash issue
5. Fix wifi run out of memory when 10 udp connection stability test
See merge request !745
Optimize configuration of base MAC address
Application developer can call APIs to configure base MAC address
instead of using menuconfig.
See merge request !744
component/esp32 : fix dualcore bug
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
See merge request !742
component/bt: fix adv stop event bug and add attribute table create
- Fix bug that advertising stop event produced while calling start_adv function
- Modify gatt server adv data and scan rsp data raw setting
- Add create attribute table error msg
- Delete redundant printf in previous commits
See merge request !739
1. When dual core cpu run access DPORT register, must do protection.
2. If access DPORT register, must use DPORT_REG_READ/DPORT_REG_WRITE and DPORT_XXX register operation macro.
SPI: Various fixes (examples, mem leak, arg check)
- Fix SPI master example to use DMA-capable memory for display initialization. Fixes https://github.com/espressif/esp-idf/issues/551
- SPI master: Do not leak DMA descriptor pointer array on free
- SPI Master/Slave: Check if DMA'ed buffers actually live in DMA-capable memory
See merge request !735
error
- Fix bug that advertising stop event produced while calling start_adv function
- Modify gatt server adv data and scan rsp data raw setting
- add create attribute table error msg
- Delete redundant printf in previous commits
we'll auto assign cases to test jobs so we don't need those config
files. cases with different wifi modes will now be generated when
creating test case database, we need to remove them from YAML files.
FATFS fixes and tests
This MR includes a set of fixes related to FATFS, SDMMC, and wear levelling:
- `esp_vfs_fat_spiflash_mount` uses `FM_SFD` flag when creating the partition. The volume layout (given in `VolToPart` variable) was not compatible with SFD mode, so mkfs was failing. This fixes the volume layout to use "autodetect" for both volumes. Merges https://github.com/espressif/esp-idf/pull/559.
- fix `prepend_drive_to_path`function, which didn't prepend drive to path (while consuming 2k of stack space)
- fix stack overflow in vfs_fat_link function which allocated two 4kbyte `FIL` structures on the stack
- fix support for having two FATFS instances (in flash and SD) mounted at the same time
- unit tests written for FATFS on SDMMC are made common between SDMMC and WL implementations; FATFS unit tests on WL will run during CI
- fix inconsistent definition of PATH_MAX and ARG_MAX (TW12207, TW12104, https://github.com/espressif/esp-idf/issues/289)
See merge request !732
component/bt: fix some bugs related to bluetooth sniff mode in controller
1. fix some bugs in bluetooth sniff mode in controller
2. export some symbols to esp32.rom.ld including functions and global variables in ROM code
3. update libbtdm.a which includes "IRAM_ATTR" addition or removal for some functions
See merge request !729
fix(lwip): fix tcp connect fail when enable LOOPIF
when enable the LOOPIF, because of use the loopnetif, the TCP connect will fail. see TW12029
See merge request !711
- fix null pointer dereference in VFS when VFS implementations are added
and removed in different order
- vfs_fat_sdmmc, vfs_fat_spiflash: pass correct drive to mkfs
(previously it would always do mkfs in the first drive)
- add test case
This change moves actual test code into test_fatfs_common.c and
refactors setup/teardown code to be contained within separate functions.
For each SDMMC FATFS test, identical test is added which can run with
WL partition in flash.
vfs_fat_link opened two files to perform copy operation. File structures
were allocated on the stack. When _MAX_SS setting was increased in
ffconf.h due to wear levelling feature, the size of these structures
increased to ~4k each (~8k total). This exceeds stack size allocated for
tasks in most typical cases.
This change makes file structures dynamically allocated.
Originally, prepend_drive_to_path was designed to be a macro, and it
modified local path variables to point to a temporary buffers.
When it was converted into a function, modification to path variables
were no longer visible outside of this function.
In addition to that, prepend_drive_to_path allocated 2k bytes on the
stack for temporary path buffers. This is replaced with path buffers
allocated as part of vfs_fat context object. Locking is added around
parts of code which use these temporary buffers.
Additionally, _lock member of vfs_fat_ctx_t was placed after the
variable-sized files array, which caused the first entry in the
array to be never used. This change fixes the order of members
and adds comments.
1. fix some bugs in bluetooth sniff mode in controller
2. export some symbols to esp32.rom.ld including functions and global variables in ROM code
3. update libbtdm.a which includes "IRAM_ATTR" addition or removal for some functions
component/bt:fix the bug with gatt client cant not receive the gatt server service change event.
fix the bug with gatt client cant not receive the gatt server service change event.
See merge request !726
esp32: select 8M clock as RTC_FAST_CLK on startup
Even though RTC_CLK_CONFIG_DEFAULT correctly had RTC_FAST_FREQ_8M as the
fast clock, the bootloader modified fast_freq field to the currently
selected RTC_FAST_CLK (so that the clock choice is not affected by the
bootloader). The application startup code never switched to 8M clock,
which caused the default (XTAL/4) to be used as RTC_FAST_CLK. This had
caused a number of issues, such as touch pads not working in deep sleep.
Fixes https://github.com/espressif/esp-idf/issues/542.
Ref TW12053.
See merge request !709
Assert when a new task is started on a nonexisting CPU
Previously, starting a task on a CPU ID higher than the amount of CPUs FreeRTOS is configured with would not start the task and possibly have unintended side effects due to some out-of-bounds array writes. Assert on this so the app aborts cleanly.
See merge request !701
I2S driver - fixed support for 24 and 32-bits, fixed tx/rx at the same time
- Modify sample can test with 24, 32-bits audio
- Add i2s sample README
- simply i2s_push function
- change sample rates, bits per sample, channel on fly
See merge request !483
Fix SPI master CI test
CI test fails because the values it checks haven't been updated to the changes in the clock calculations. This fixes that.
See merge request !710
Feature/btdm ble bt separa
@Jack @snake @igrokhotkov @angus @island please help to review the code.
Separate the bt/ble code. After the separate, can save 15k~25k ram & 240k~460k code size(depending on the menuconfig).
See merge request !684
optimize scan before station connecting to AP
1. Store the information of AP(ssid, password, bssid, channel, etc)
into nvs when station connects to AP successfully. If station
connects to the same AP next time, it will scan the stored channel of the AP
first.
2. Add a parameter of channel for scanning before connecting to AP.
If the channel is set to 0, station will scan full channels. If it
is set to 1~13, station will only scan the channel.
See merge request !704
1. Store the information of AP(ssid, password, bssid, channel, etc)
into nvs when station connects to AP successfully. If station
connects to the same AP next time, it will scan the stored channel of the AP
first.
2. Add a parameter of channel for scanning before connecting to AP.
If it is set to 1~13, station will scan starting from the channel.
If the channel of AP is unknown, set it to 0.
Even though RTC_CLK_CONFIG_DEFAULT correctly had RTC_FAST_FREQ_8M as the
fast clock, the bootloader modified fast_freq field to the currently
selected RTC_FAST_CLK (so that the clock choice is not affected by the
bootloader). The application startup code never switched to 8M clock,
which caused the default (XTAL/4) to be used as RTC_FAST_CLK. This had
caused a number of issues, such as touch pads not working in deep sleep.
Fixes https://github.com/espressif/esp-idf/issues/542.
Ref TW12053.
Split common SPI stuff out of master driver; add slave driver; add workaround for DMA issue.
This merge req mainly adds a slave device. In order to do this, the original master driver is refactored into common code shared by master and slave modes, and a slave driver is added.
The other things added are:
- Added a workaround for a 'feature' of the ESP32 silicon that can lock up the receive DMA channel in some situations. This can only be fixed by resetting *both* DMA channels. The workaround implemented makes sure that the reset only happens when both channels are idle
- Got rid of the automatic choice between register- and DMA-based transfers. The master (and slave) code will now always go for a DMA transfer if a DMA channel is given, and always go for register-based transfers if no DMA channel is given.
- Add in a bunch of fixes for outstanding Github issues.
See merge request !659
Add support 24, 32 bits
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
Add support 24, 32 bits
reduce push function
Modify sample can test with 24, 32-bits
Add i2s sample README
Fixed i2s_set_clk got reset sometime
can changes bit-wide while running
Fix sample rate calculation for DAC mode from @jeroen
modify example can change bits per sample every 5 seconds
cleanup
add comment for bytes_per_sample
update as @angus suggestions
Add i2s_set_clk api
I2S driver bug fixed as following log:
@jxmao optimize i2s_zero_buffer
@jxmao correct config support slave mode
@jxmao correct setup pin support tx/rx at the same time
Enhance pin power
@jxmao add dynamic change number of channels
remove nvs_init
remove start log and enhance power pin setup
using enum for i2s_channel and i2s_bits_per_sample, return ESP_ERR_INVALID_ARG when check params
validate i2s_bits_per_sample and channel
check tx & rx buffer before fill zero
remove checking channel as @jxmao suggest
limit dma buffer
modify i2s pin back to gpio mux before configure gpio matrix, resolve github issue #512
limit dma buffer to 4092
change gpio_matrix_*_check to inline function, remove some comments and rename test_i2s function to setup_triangle_sine_waves
for change commit title
esp32: Core dump sanity checks
Adds sanity checks when doing core dump to flash
- CRC for core dump flash partition config
- Tasks with corrupted TCBs are skipped
- Assertions to check that nothing is written beyond core dump flash partition
Ref TW11879
See merge request !686
- CRC for core dump flash partition config
- Tasks with corrupted TCBs are skipped
- Assertions to check that nothing is written beyond core dump flash partition
add support for 32k XTAL as RTC_SLOW_CLK source
- RTC_CNTL_SLOWCLK_FREQ define is removed; rtc_clk_slow_freq_get_hz
function can be used instead to get an approximate RTC_SLOW_CLK
frequency
- Clock calibration is performed at startup. The value is saved and used
for timekeeping and when entering deep sleep.
- When using the 32k XTAL, startup code will wait for the oscillator to
start up. This can be possibly optimized by starting a separate task
to wait for oscillator startup, and performing clock switch in that
task.
- Fix a bug that 32k XTAL would be disabled in rtc_clk_init.
- Fix a rounding error in rtc_clk_cal, which caused systematic frequency
error.
- Fix an overflow bug which caused rtc_clk_cal to timeout early if the
slow_clk_cycles argument would exceed certain value
- Improve 32k XTAL oscillator startup time by introducing bootstrapping
code, which uses internal pullup/pulldown resistors on 32K_N/32K_P
pins to set better initial conditions for the oscillator.
Ref TW11683.
Ref https://esp32.com/viewtopic.php?f=13&t=1570
Fixes https://github.com/espressif/esp-idf/issues/337.
See merge request !696
- RTC_CNTL_SLOWCLK_FREQ define is removed; rtc_clk_slow_freq_get_hz
function can be used instead to get an approximate RTC_SLOW_CLK
frequency
- Clock calibration is performed at startup. The value is saved and used
for timekeeping and when entering deep sleep.
- When using the 32k XTAL, startup code will wait for the oscillator to
start up. This can be possibly optimized by starting a separate task
to wait for oscillator startup, and performing clock switch in that
task.
- Fix a bug that 32k XTAL would be disabled in rtc_clk_init.
- Fix a rounding error in rtc_clk_cal, which caused systematic frequency
error.
- Fix an overflow bug which caused rtc_clk_cal to timeout early if the
slow_clk_cycles argument would exceed certain value
- Improve 32k XTAL oscillator startup time by introducing bootstrapping
code, which uses internal pullup/pulldown resistors on 32K_N/32K_P
pins to set better initial conditions for the oscillator.
1.change the rowdata to rodata;
2.change BT_ACL_CONNECTIONS to Maximum BT/BLE connection count.
3. change the comments of bt_target.h:505 from 40 to 5.
wear levelling
This MR adds wear levelling component. It presents an interface similar to the interface of spi_flash and esp_partition. Inside, it stores data inside a partition to in a way that reduces worst case number of erase cycles for any given sector.
Also included are APIs similar to the ones provided for SDMMC to mount FAT filesystem on top of the wear levelling partition. A simple example shows how this API can be used.
Ref TW10338.
See merge request !567
- reorder directories listed in COMPONENT_SRCDIRS so that
subdirectories precede parent directories
- don’t include PPP source directories if PPP support is not enabled
1. close classic bt, can save 233k code size;
2. close smp module, can save 136k code size;
3. close gattc module, can save 24k code size;
4. close gatts module, can save 16k code size;
4. close the bluedroid stack log, can save 120k code size.
XTAL frequency detection, support for selecting XTAL frequency
This MR adds more robust XTAL frequency detection code (which gets run in the bootloader) and an option to set XTAL frequency in Kconfig. By default we still use autodetection, since it is more reliable than the one used in ROM code.
This will help with issues about XTAL frequency detection in high ambient temperature conditions.
Ref TW12008
See merge request !694
sdmmc: handle card removal when CD is not used
When SD card is removed during transaction, SDMMC peripheral can report
a range of errors, such as timeouts, CRC errors, start/end bit errors.
Under normal conditions (card is inserted), SDMMC peripheral also generates
command done or data done interrupts. When the card is removed, such
interrupts may not be always generated.
This change fixes handling of timeout interrupts and SBE interrupts.
It also adds a one second timeout into the event processing loop. This
timeout allows applications to recover in cases when the SDMMC peripheral
doesn’t generate command/data done event on card removal.
Fixes TW11592.
See merge request !678
fat/sdmmc: unmount FATFS object on error
Failure to call f_mount(NULL,...) makes FATFS attempt to clean up the old
FS object upon next mount. If previous mount operation has failed, some
parts of FS object may not be fully initialized, which will cause errors
(such as attempting to delete a mutex which wasn’t allocated).
Fixes TW11594.
See merge request !679
ROM code already implements XTAL frequency detection, but it uses the 8M
clock before the clock tuning parameters are initialized. With the
zero clock tuning parameter, 8M clock has significant frequency deviation
at high temperatures, which can lead to erroneous detection of 40 MHz
crystal as a 26 MHz one.
This change adds XTAL frequency detection code to rtc_clk_init routine,
and detection is performed after the 8M clock tuning parameter as been
initialized.
lwip: fix tcp stable test abort issue
This MR covers following changes:
1. Modify dhcp server timer to 1 seconds
2. Enable ETHARP_TRUST_IP_MAC. Consider following scenario: we are in throughput test or traffic stability test, if this option is disabled, then every 5 minutes, the IP/MAC entry in arch cache is aged out, however, the traffic continuously send to lwip from application, because there is no IP/MAC entry in ARP cache, then the packets have to be buffered in ARP queue and a ARP request is triggered, but the ARP queue can only holds 3 packets, the later packets will be dropped, then if the traffic is big, a lot of packets will be dropped here before we get the right ARP response. For TCP, this will trigger re-transmit, it's intolerable for some application, such as real time audio, if re-transmit happen, then performance of voice will be impact. For UDP, sometimes it may also cause problem, such as DHCP, if here we failed to send the DHCP here, we has to wait the DHCP timeout etc... so this option is enabled here by default.
See merge request !681
esp32: update wifi lib for limitting dynamic wifi buffer
Add limit for all dynamic wifi ebuf to avoid wifi run out of memory in some extreme scanrio.
The default max allocated dynamic tx buffer is 32
The default max allocated dynamic rx buffer is 64, make default value is bigger because when all packets we received are small packets, e.g. the length is 64Bytes, then 64K can hold 1000 packets, so 64 maybe a good candidate default value, anyway the customer can configure it via menuconfig.
The default dynamic wifi internal long/long-long mgmt is 32, generally 32 is enough for mgmt packet (beacon/auth/assoc/probe/null etc). Generally when all the 32 mgmt buffer is run out of memory, it means internal wifi state machine may has problem, we need to debug it.
See merge request !683
There are some RODATAs of libphy.a that are called in ISR. So need
to put them into DRAM to avoid access them when R/W SPI flash. Due
to the RODATAs which are called in ISR haven't been picked out to
put into DRAM, put all of the RODATA of libphy.a into DRAM. This
will be optimized in the future.
soc: allow REG_SET_FIELD to be used for bit fields
- Fixes an issue with `rtc_clk_apll_enable`: https://esp32.com/viewtopic.php?f=13&t=1673
- Fixes `rtc_clk_fast_freq_set` function always selecting XTAL/4 as fast clock source.
- Fixes regression in deep sleep current (7uA instead of 5uA).
See merge request !674
rtc_clk_init: handle case when XTAL frequency has already been set
On first reset, ROM code writes the estimated XTAL frequency into
RTC_APB_FREQ_REG (aka STORE5). If the application doesn’t specify exact
XTAL frequency (which is always the case for now), rtc_clk_init will
guess what kind of XTAL is used (26M or 40M), based on the estimated
frequency. Later, detected frequency is written into RTC_XTAL_FREQ_REG
(aka STORE4).
When the application switches clock source to PLL, APB frequency changes
and RTC_APB_FREQ_REG is updated. If the application encounters an RTC
WDT reset, RTC_APB_FREQ_REG will not be updated prior to reset. Once the
application starts up again, it will attempt to auto-detect XTAL
frequency based on RTC_APB_FREQ_REG, which now has value of 80000000.
This will fail, and rtc_clk_xtal_freq_estimate will fall back to the
default value of 26 MHz. Due to an incorrect XTAL frequency, PLL
initialization will also take incorrect path, and PLL will run at a
different frequency. Depending on the application this may cause just
garbage output on UART or a crash (if WiFi is used).
This change checks if RTC_XTAL_FREQ_REG has already been set before trying
to estimate XTAL frequency based on the value of RTC_APB_FREQ_REG, and
uses RTC_XTAL_FREQ_REG value if it is valid.
Fixes TW11738.
See merge request !691
Base MAC address can be stored in default manufacture-defined or customer
pre-defined place in EFUSE and other place e.g. flash or EEPROM.
If choose to use base MAC address which is stored in other place, please
call esp_base_mac_addr_set_external() before initializing WiFi/BT/Ehternet.
On first reset, ROM code writes the estimated XTAL frequency into
RTC_APB_FREQ_REG (aka STORE5). If the application doesn’t specify exact
XTAL frequency (which is always the case for now), rtc_clk_init will
guess what kind of XTAL is used (26M or 40M), based on the estimated
frequency. Later, detected frequency is written into RTC_XTAL_FREQ_REG
(aka STORE4).
When the application switches clock source to PLL, APB frequency changes
and RTC_APB_FREQ_REG is updated. If the application encounters an RTC
WDT reset, RTC_APB_FREQ_REG will not be updated prior to reset. Once the
application starts up again, it will attempt to auto-detect XTAL
frequency based on RTC_APB_FREQ_REG, which now has value of 80000000.
This will fail, and rtc_clk_xtal_freq_estimate will fall back to the
default value of 26 MHz. Due to an incorrect XTAL frequency, PLL
initialization will also take incorrect path, and PLL will run at a
different frequency. Depending on the application this may cause just
garbage output on UART or a crash (if WiFi is used).
SPI transfer length is bits, not bytes, so the error should indicate bits. Also, there are separate lengths for rx and
tx (confusingly named rxlength and length... if rxlength is 0, length is used). The code checks the tx length for the
rx, so it never validates rxlength.
Originally contributed as part of #511https://github.com/espressif/esp-idf/pull/511
Since mbedtls_net_errno is reset by fcntl, it is reset after calling
net_would_block, so the call to mbedtls_net_errno in mbedtls_net_recv
and mbedtls_net_send will always get back 0. This change propagates
the value returned by mbedtls_net_errno up through net_would_block,
to allow the correct error value to be used and avoid a redundant
call to mbedtls_net_errno.
Merges PR #511https://github.com/espressif/esp-idf/pull/511
Failure to call f_mount(NULL,...) makes FATFS attempt to clean up the old
FS object upon next mount. If previous mount operation has failed, some
parts of FS object may not be fully initialized, which will cause errors
(such as attempting to delete a mutex which wasn’t allocated).
When SD card is removed during transaction, SDMMC peripheral can report
a range of errors, such as timeouts, CRC errors, start/end bit errors.
Under normal conditions (card is inserted), SDMMC peripheral also generates
command done or data done interrupts. When the card is removed, such
interrupts may not be always generated.
This change fixes handling of timeout interrupts and SBE interrupts.
It also adds a one second timeout into the event processing loop. This
timeout allows applications to recover in cases when the SDMMC peripheral
doesn’t generate command/data done event on card removal.
Remove ESP_EARLY_LOGI before bss is initialized; it crashes the CPU
There's an ESP_EARLY_LOGI line that can get called before the BSS is initialized; the early logging code doesn't cope well with that: it checks if FreeRTOS is up, but the variables it uses for that contains garbage because it isn't cleared yet, giving the wrong result. The logging code then tries to set a mux, crashing the entire system. This patch removes the log line and adds a warning at the BSS initialization line not to do anything complex before that point.
Fixes https://github.com/espressif/esp-idf/issues/523
See merge request !671
- Implements application tracing module which allows to send arbitrary
data to host over JTAG. This feature is useful for analyzing
program modules behavior, dumping run-time application data etc.
- Implements printf-like logging functions on top of apptrace module.
This feature is a kind of semihosted printf functionality with lower
overhead and impact on system behaviour as compared to standard printf.
