1. The 2nd bootloader always call `rom_spiflash_unlock()`, but never help to clear the WEL bit when exit. This may cause system unstability.
This commit helps to clear WEL when flash configuration is done.
**RISK:** When the app starts, it didn't have to clear the WEL before it actually write/erase. But now the very first write/erase operation should be done after a WEL clear. Though the risk is little (all the following write/erase also need to clear the WEL), we still have to test this carefully, especially for those functions used by the OTA.
2. The `rom_spiflash_unlock()` function in the patch of ESP32 may (1) trigger the QPI, (2) clear the QE or (3) fail to unlock the ISSI chips.
Status register bitmap of ISSI chip and GD chip:
| SR | ISSI | GD25LQ32C |
| -- | ---- | --------- |
| 0 | WIP | WIP |
| 1 | WEL | WEL |
| 2 | BP0 | BP0 |
| 3 | BP1 | BP1 |
| 4 | BP2 | BP2 |
| 5 | BP3 | BP3 |
| 6 | QE | BP4 |
| 7 | SRWD | SRP0 |
| 8 | | SRP1 |
| 9 | | QE |
| 10 | | SUS2 |
| 11 | | LB1 |
| 12 | | LB2 |
| 13 | | LB3 |
| 14 | | CMP |
| 15 | | SUS1 |
QE bit of other chips are at the bit 9 of the status register (i.e. bit 1 of SR2), which should be read by RDSR2 command.
However, the RDSR2 (35H, Read Status 2) command for chip of other vendors happens to be the QIOEN (Enter QPI mode) command of ISSI chips. When the `rom_spiflash_unlock()` function trys to read SR2, it may trigger the QPI of ISSI chips.
Moreover, when `rom_spiflash_unlock()` try to clear the BP4 bit in the status register, QE (bit 6) of ISSI chip may be cleared by accident. Or if the ISSI chip doesn't accept WRSR command with argument of two bytes (since it only have status register of one byte), it may fail to clear the other protect bits (BP0~BP3) as expected.
This commit makes the `rom_spiflash_unlock()` check whether the vendor is issi. if so, `rom_spiflash_unlock()` only send RDSR to read the status register, send WRSR with only 1 byte argument, and also avoid clearing the QE bit (bit 6).
3. `rom_spiflash_unlock()` always send WRSR command to clear protection bits even when there is no protection bit active. And the execution of clearing status registers, which takes about 700us, will also happen even when there's no bits cleared.
This commit skips the clearing of status register if there is no protection bits active.
Also move the execute_flash_command to be a bootloader API; move
implementation of spi_flash_wrap_set to the bootloader
Summary of changes:
- bootloader_clock split into *_clock_init and *_clock_loader.
Only esp_clk_apb_freq is in *_clock_loader.
- bootloader_common moved out of loader; functions needed in loader
(or, referenced from bootloader_utility) were moved into
bootloader_common_loader.c.
- assert and abort moved into bootloader_panic, made part of the
loader
- rtc_clk and rtc_time made part of loader
* changing dependencies from unity->cmock
* added component.mk and Makefile.projbuild
* ignore test dir in gen_esp_err_to_name.py
* added some brief introduction of CMock in IDF
Sometimes the flash size read from bootloader is not correct. This may
forbid SPI Flash driver from reading the the area larger than the size
in bootloader header.
When the new config option is enabled, the latest configured
ESPTOOLPY_FLAHSIZE in the app header will be used to override the value
read from bootloader header.
bootloader_support: Fix bootloader_common_get_sha256_of_partition(), can handle a long image
Closes IDFGH-3594
See merge request espressif/esp-idf!9509
Allows booting in QIO/QOUT mode or with PSRAM on ESP32-PICO-V3 and
ESP32-PICO-V3-O2 without any config changes.
Custom WP pins (needed for fully custom circuit boards) should still be compatible.
esp32/esp32s2: Reduce using ESP_EARLY_LOGx and move some code after the stdout initialization in startup code
Closes IDFGH-3367
See merge request espressif/esp-idf!8904
Reduces write cycles, and useful on ESP32 ECO3 as UART_DIS_DL is protected by
the same efuse.
Also fixes accidental macro definition introduced in 7635dce502
flash_encryption: modify additional efuses burning method to fix them are not being written
flass_encryption: burn efuse to disable boot from RAM space
flash_encryption: added better checking for key generation state plus set read and write protect for them
soc esp32s2: Add register-level bit definitions for read & wrote protect bits
esp32s2: Fixes for flash encryption
- Write efuses in a batch
- Fix some detection of whether existing efuse blocks are read/write protected
flash_enctryption: enabled flash encryption example on esp32s2
bootloader: raise WDT overflow value providing sufficient interval to encrypt app partition
flash_ encrypt: Fixed the TODOs on flash encryption key generation for esp32s2
flash_encryption: added secure boot features to flash enctryption for esp32s2
bootloader: leave only esp32s2 compatible potentially insecure options on menuconfig.
flash_encryption: removed secure boot version 1 from esp32s2 encryption code
flash_encryption: added CONFIG_SECURE_FLASH_REQUIRE_ALREADY_ENABLED option for esp32s2
flash_encryption: fixed the count of left plaintext flash
flash_encryption: disable dcache and icache download when using encryption in release mode
flash_encryption: add cache potentally insecure options for s2 chips
flash_encryption: fixed bug which bricked some chips in relase mode
If BLK2 is empty then it's OK to continue with a warning (otherwise it may spook users into thinking
something this is wrong, but this is the expected workflow.)
If BLK2 is not empty and doesn't match then we need to fail because it won't be possible to
trust the signature.
Previous method was to write-protect this efuse, however on ECO3
the write protect field also covers the UART_DOWNLOAD_DIS efuse.
Doing it this way keeps the possibility of disabling UART download
mode, later.
This commit updates the watchdog timers (MWDT and RWDT)
in the following ways:
- Add seprate LL for MWDT and RWDT.
- Add a combined WDT HAL for all Watchdog Timers
- Update int_wdt.c and task_wdt.c to use WDT HAL
- Remove most dependencies on LL or direct register access
in other components. They will now use the WDT HAL
- Update use of watchdogs (including RTC WDT) in bootloader and
startup code to use the HAL layer.
In commit 02d2903e39, mbedtls was
updated to release v2.16.5, where it was made mandatory to initialize
mbedtls_ctr_drbg_context before using same. It was fixed in wpa supplicant
but missed out in secure boot v2 verification code. This commit
fixes that.
Goal is that multiple faults would be required to bypass a boot-time signature check.
- Also strengthens some address range checks for safe app memory addresses
- Change pre-enable logic to also check the bootloader signature before enabling SBV2 on ESP32
Add some additional checks for invalid sections:
- Sections only partially in DRAM or IRAM are invalid
- If a section is in D/IRAM, allow the possibility only some is in D/IRAM
- Only pass sections that are entirely in the same type of RTC memory region
On the ESP32S2, rtc_clk_cal(RTC_CAL_RTC_MUX) measures the frequency
of the 90kHz RTC clock regardless of the selected slow clock
frequency. Keep track which clock is selected and pass the argument
to rtc_clk_cal accordingly.
fix clock choices
update rtc 32k xtal code for s2
missed api in rtc.h
bootloader_clock: update for S2
1. use spi functions in rom
2. remove unnecessary GPIO configurations.
3. remove unnecessary dummy settings.
4. enable dummy out function
5. flash and psram have independent timing setting registers.
6. no need to set 1.9v for LDO in 80Mhz
7. set IO driver ability to 1 by default.
8. no need to use GPIO matrix on esp32s2, IO MUX is recommended
9. enable spi clock mode and IO mode settings
1. Delete bootloader_clock_get_rated_freq_mhz, esp32s2 do not need it right now
2. Remove bootloader_flash_gpio_config () because it has the same function as bootloader_flash_dummy_config
DISABLED_FOR_TARGETS macros are used
Partly revert "ci: disable unavailable tests for esp32s2beta"
This partly reverts commit 76a3a5fb48.
Partly revert "ci: disable UTs for esp32s2beta without runners"
This partly reverts commit eb158e9a22.
Partly revert "fix unit test and examples for s2beta"
This partly reverts commit 9baa7826be.
Partly revert "efuse: Add support for esp32s2beta"
This partly reverts commit db84ba868c.
* Don't bother checking the chip revision if it looks like the partition
doesn't really contain an app
* Don't print the "info" level about the revision & min revision unless
we're in the bootloader (otherwise it gets printed at random times
during the OTA process)
bootloader_random_enable() and bootloader_random_disable() functions
can be used in app.
This MR added the protection for shared CLK_EN and RST_EN registers.
and all ECDSA to be disabled if secure boot is not enabled
Previously if ECDSA disabled in config then secure_boot_signatures.c would
fail to build (whether or not secure boot was enabled).
To avoid breaking apps that might be using the signature scheme with custom OTA
without enabling secure boot signatures in config, this change just disables
this functionality if unavailable in mbedTLS config.
Possible fix for root cause of https://github.com/espressif/esp-idf/pull/3703
Commit 8cd04c80 has added a dependency of efuse component on
esp_clk_apb_freq, however there was no definition of this function in
the bootloader context.
Reported at https://esp32.com/viewtopic.php?f=13&t=12035
This saves time when waking up from deep sleep, but potentially decreases
the security of the system. If the application able to modify itself
(especially areas that are loaded into RAM) in flash while running
without crashing or is modifies the cached bits of information about
what was last booted from the bootloader, this could cause security
issues if the user does a "deep sleep reset" since the full validation
is skipped.
Signed-off-by: Tim Nordell <tim.nordell@nimbelink.com>
No need to take this step if we are not doing image validation. The
obfuscation only buys us a tiny bit of "security" anyways since the
main parts of flash are memory mapped, too. This saves a little bit of
wake-up time when waking up from deep sleep when the
BOOTLOADER_SKIP_VALIDATE_IN_DEEP_SLEEP option is set.
Signed-off-by: Tim Nordell <tim.nordell@nimbelink.com>
We fixed some flash bugs in bootloader, but for the users used the old
vrsion bootloader, they can not fix these bugs via OTA, the solution is
add these updates in app startup.
These updates include:
1. SPI flash gpio matrix and drive strength configuration
2. SPI flash clock configuration
3. SPI flash read dummy configuration
4. SPI flash cs timing configuration
5. Update flash id of g_rom_flashchip
Made MMU pages available check in `esp_image_format.c`
This now makes it possible to map and process bootoader image as well in chunks when image doesn't fit completely into available free pages.
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
Do not include bootloader in flash target when secure boot is enabled.
Emit signing warning on all cases where signed apps are enabled (secure
boot and signed images)
Follow convention of capital letters for SECURE_BOOT_SIGNING_KEY variable, since it is
relevant to other components, not just bootloader.
Pass signing key and verification key via config, not requiring
bootloader to know parent app dir.
Misc. variables name corrections
