Add .eh_frame and .eh_frame_hdr sections to the binary (can be
enabled/disabled within menuconfig). These sections are parsed
when a panic occurs. Their DWARF instructions are decoded and
executed at runtime, to retrieve the whole backtrace. This
parser has been tested on both RISC-V and x86 architectures.
This feature needs esptool's merge adjacent ELF sections feature.
* MR 14212 accidentally disabled the test
"spi_flash deadlock with high priority
busy-waiting task"
for all targets except S3 without legacy
flash implementation. The test is now
disabled for all targets, since
the same issue appeared on other targets, too.
After we have the performance dashboard, we have more data and no longer depend on the threshold to ensure performance.
Set looser performance thresholds to avoid CI failure.
Partially reverted 08f1bbe0c7.
The host should have this flexibility, which is consistent to the cs_hold argument.
However, the user should know as less as possible about the host.
So the wrapper layer (esp_flash_spi_init.c) should cover this, helping to set cs_setup to 1, to meet the common requirements.
Regression in ede477ea65 for host tests only - ESP-IDF supports
strlcpy() but strlcpy & strlcat are currently no-ops in the host
tests (to avoid libbsd dependency).
Additionally, always enable the partition MD5 check if flash encryption is on in
Release mode. This ensures the partition table ciphertext has not been modified
(CVE-2021-27926).
The exception is pre-V3.1 ESP-IDF bootloaders and partition tables, which
don't have support for the MD5 entry.
spi_flash: refactoring flash encryption implementations into new api
Closes IDFGH-4493, IDFGH-4423, and IDF-657
See merge request espressif/esp-idf!12569
When `DIS_USB_JTAG` eFuse is NOT burned (`False`), it is not possible
to set pins 18 and 19 as GPIOs. This commit solves this by manually
disabling USB JTAG when using pins 18 or 19.
The functions shall use `gpio_hal_iomux_func_sel` instead of
`PIN_FUNC_SELELECT`.
Enable shared stack watchpoint for overflow detection
Enable unit tests:
* "test printf using shared buffer stack" for C3
* "Test vTaskDelayUntil" for S2
* "UART can do poll()" for C3
On C3 the cache is programmatically split between Icache and dcache and with the default setup we dont leave a lot pages
available for additional mmaps into instruction space. Disabling this test for now since any hypothetical use case for this
is no longer supported "out of the box"
This reverts commit bf35ef1ce7.
It has been noticed that there are scenarios where even though firmware is not enabled
with flash encryption config feature, it should be able to write to encrypted partitions.
This revert adds the feature back which was removed around v4.0 timelines, and same
change will be backported to all releases (upto v4.0) for consistency.
- Adds arbitration between the erase and write in suspend mode
(If the flash memory is suspended then only a read operation can be performed.)
- espcoredump: Dump does not use suspend feature, just resume before continue.
- spi_flash: Add release_cpu() to do suspend/release_cpu/resume
There is no ccomp timer on C3, which means our performance tests will start
failing again due to variance caused by cache misses.
This MR adds TEST_PERFORMANCE_CCOMP_ macro that will only fail
performance test if CCOMP timer is supported on the target
* General tests like page loading from flash
* Rough test of fixed-size data types
* Rough test of blob read
* Added coverage target in cmake, also accessible
via `idf.py coverage`
* Fixed unsigned comparison in comp. enum table
* introducing temporary LINUX_TARGET define
The following three headers will be mockes:
* esp_flash.h
* esp_spi_flash.h
* esp_partition.h
* counter functions live in own header
* add spi_flash sim dir for esp_err.h to Unity
* modified gen_esp_err_to_name.py to ignore
sim/ dir in spi_flash component
Add cmock .yaml config file
Add spi hal header until soc can mock the hal
layer as well.
* add toolchain file
* add linux to preview targets
* add stub for dfu number in cmake
* excluded unity runner per default
* Added esp_attr.h and esp_partition.h linux stubs
* component.cmake check list for emptyness
* added switch for linux in unity cmake file
* Added Linux host example app
From now on, we have two tags for esp_flash tests:
- [esp_flash] for main flash chip only tests
- [esp_flash_3] for tests with external flash chips
To Run all tests, type `[esp_flash`; to run tests for main flash chip
only, type `[esp_flash].
There is a periodically yield in the esp_flash driver, to ensure the
cache will not be disabled for too long on ESP32.
On ESP32-S2 and later, we need to support more different kind of yield:
1. polling conditions, including timeout, SW read request, etc.
2. wait for events, including HW done/error/auto-suspend, timeout
semaphore, etc.
The check_yield() and yield() is separated into two parts, because we
may need to insert suspend, etc. between them.
