* Disable Tx interrupts to fix race condition of missing Rx interrupt
* Check if GPIO interrupt is asserted periodically if the ISR event missed
Closes https://github.com/espressif/esp-idf/issues/6414
Ethernet driver events properly bounded with ESP NETIF actions to support multiple Ethernet modules used at a time.
Components using Ethernet updated to conform with new API.
Closes https://github.com/espressif/esp-idf/issues/7318
Increase the interrupt reassert level timing so the chances of missing
two consecutive events are minimal.
Enable only SIR_RECV interrupt event, so the SEND events are not used
for GPIO signal.
If the GPIO interrupt is re-asserted too quickly it could be missed. If this happens the driver goes silent and never receives any data. Recover by periodic checks of the IO signal level
Also updated KSZ8851SNL per internal code review:
* Removed Link status change interrupt as it's handled with polling
* Added auto negotiation timeout
* Updated typedefs, moved types to appropriate source, updated
components/esp_eth/src/ksz8851.h to use only inherent device types
* Applied IDF code formatting
* Updated header file order to include first the most generic to more
specific
The issue typically happens for link-down during Tx. Added two retry levels, one before checking the sanity of the w5500 phy register and another for the Tx done itself (if the device is in the sane state)
Closes https://github.com/espressif/esp-idf/issues/6233
Reading SPI data may come in 4-byte units and thus result in unwanted
overwrites if smaller size registers read, especially if multiple placed
one after another. Fixed by using direct reads to `trans` structure for
sizes smaller or equal to 4.
Closes https://github.com/espressif/esp-idf/issues/6579
When `DIS_USB_JTAG` eFuse is NOT burned (`False`), it is not possible
to set pins 18 and 19 as GPIOs. This commit solves this by manually
disabling USB JTAG when using pins 18 or 19.
The functions shall use `gpio_hal_iomux_func_sel` instead of
`PIN_FUNC_SELELECT`.
W5500 features an Ethernet MAC+PHY, plus a HW SOCKET implementation.
But in IDF, we only use software TCP/IP stack, which means we have
to bypass the HW TCP/IP stack in W5500.
So we enables the MAC RAW mode in W5500.
* Target components pull in xtensa component directly
* Use CPU HAL where applicable
* Remove unnecessary xtensa headers
* Compilation changes necessary to support non-xtensa gcc types (ie int32_t/uint32_t is no
longer signed/unsigned int).
Changes come from internal branch commit a6723fc
* changing dependencies from unity->cmock
* added component.mk and Makefile.projbuild
* ignore test dir in gen_esp_err_to_name.py
* added some brief introduction of CMock in IDF
DISABLED_FOR_TARGETS macros are used
Partly revert "ci: disable unavailable tests for esp32s2beta"
This partly reverts commit 76a3a5fb48.
Partly revert "ci: disable UTs for esp32s2beta without runners"
This partly reverts commit eb158e9a22.
Partly revert "fix unit test and examples for s2beta"
This partly reverts commit 9baa7826be.
Partly revert "efuse: Add support for esp32s2beta"
This partly reverts commit db84ba868c.
OpenCores Ethernet MAC has a relatively simple interface, and is
already supported in QEMU. This makes it a good candidate for enabling
network support when running IDF apps in QEMU, compared to the
relatively more complex task of writing a QEMU model of ESP32 EMAC.
This driver is written with QEMU in mind: it does not implement or
handle things that aren't implemented or handled in the QEMU model:
error flags, error interrupts. The transmit part of the driver also
assumes that the TX operation is done immediately when the TX
descriptor is written (which is the case with QEMU), hence waiting for
the TX operation to complete is not necessary.
For simplicity, the driver assumes that the peripheral register
occupy the same memory range as the ESP32 EMAC registers, and the
same interrupt source number is used.
1. simplify deallocate in esp_eth_mac_new_esp32, esp_eth_mac_new_dm9051
2. remove blocking operation in os timer callback
3. check buffer size in ethernet receive function
Rename and add multiple kconfig compiler options. New compiler options
COMPILER_OPTIMIZATION_PERF and COMPILER_OPTIMIZATION_NONE have been added.
Optimize "Debug" and "Release" options to "Default" and "Size" respectively.
This commit also does the following:
- The COMPILER_OPTIMIZATION_PERF option introduced multiple bug.
This commit fixes those bugs.
- build.yml also updated to test for the new optimization options.
