ESP32C3/ESP32S3: Fix cpu crash bug when wakeup from lightsleep for memory data miss
Closes IDF-162 and IDF-4923
See merge request espressif/esp-idf!17823
introduced in e44ead5356
1. The int8M power domain config by default is PD. While LEDC is using
RTC8M as clock source, this power domain will be kept on.
But when 8MD256 is used as RTC clock source, the power domain should
also be kept on.
On ESP32, there was protection for it, but broken by commit
e44ead5356. Currently the power domain
will be forced on when LEDC is using RTC8M as clock source &&
!int8m_pd_en (user enable ESP_PDP_DOMAIN_RTC8M in lightsleep). Otherwise
the power domain will be powered off, regardless of RTC clock source.
In other words, int8M domain will be forced off (even when 8MD256
used as RTC clock source) if LEDC not using RTC8M as clock source, user
doesn't enable ESP_PDP_DOMAIN_RTC8M, or in deep sleep.
On later chips, there's no such protection, so 8MD256 could't be used as
RTC clock source in sleep modes.
This commit adds protection of 8MD256 clock to other chips. Fixes the
incorrect protection logic overriding on ESP32. Now the power domain
will be determiend by the logic below (order by priority):
1. When RTC clock source uses 8MD256, power up
2. When LEDC uses RTC8M clock source, power up
3. In deepsleep, power down
4. Otherwise determined by user config of ESP_PDP_DOMAIN_RTC8M,
power down by default. (This is preferred to have highest
priority, but it's kept as is because of current code structure.)
2. Before, after the macro `RTC_SLEEP_CONFIG_DEFAULT` decides dbias, the
protection above may force the int8m PU. This may cause the inconsistent
of dbias and the int8m PU status.
This commit lifts the logic of pd int8m/xtal fpu logic to upper layer
(sleep_modes.c).
Related: https://github.com/espressif/esp-idf/issues/8007, https://github.com/espressif/esp-idf/pull/8089
temp
Moved the following kconfig options out of the target component:
* CONFIG_ESP*_DEFAULT_CPU_FREQ* -> esp_system
* ESP*_REV_MIN -> esp_hw_support
* ESP*_TIME_SYSCALL -> newlib
* ESP*_RTC_* -> esp_hw_support
Where applicable these target specific konfig names were merged into
a single common config, e.g;
CONFIG_ESP*_DEFAULT_CPU_FREQ -> CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ
1. Clean up clk usage in IDF, replace rtc_clk_xtal/apb_freq_get with
upper level API esp_clk_xtal/apb_freq
2. Fix small errors and wrong comments related to clock
3. Add clk_tree_defs.h to provide an unified clock id for each chip
Modify the NGed drivers to adopt new clock ids
This commit updates the visibility of various header files and cleans up
some unnecessary inclusions. Also, this commit removes certain header
include paths which were maintained for backward compatibility.
The following files were deleted:
- components/esp_hw_support/include/soc/cpu.h
- components/soc/esp32s3/include/soc/cpu.h
The following functions are deprecated:
- get_sp()
The following functions declared in soc/cpu.h are now moved to esp_cpu.h:
- esp_cpu_configure_region_protection()
The following functions declared in soc/cpu.h are now moved to components/xtensa/include/esp_cpu_utils.h:
- esp_cpu_process_stack_pc()
All files with soc/cpu.h inclusion are updated to include esp_cpu.h instead.
Signed-off-by: Sudeep Mohanty <sudeep.mohanty@espressif.com>
peripheral enable/disable usually should be managed by driver itself,
so make it as espressif private APIs, not recommended for user to use it
in application code.
However, if user want to re-write the driver or ports to other platform,
this is still possible by including the header in this way:
"esp_private/peripheral_ctrl.h"
When the application is being debugged it should check the call result (esp_cpu_in_ocd_debug_mode())
is not given volt.glitch attack - so the result is triple-checked by ESP_FAULT_ASSERT macro. In case
the check fails, the system is reset immediately
IDF-4014
When not compiling bootloader, a spinlock will be used for reading or writing
I2C internal devices/registers.
When compiling for bootloader, no need to use any lock.
1. add some efuse api to get rtc & digital voltage
2. set dig_rtc voltage to a fix value storing in efuse no mater which cpu frequency
3. modify hardware code in bootloader to fit all c3 ECO3 version
Includes a note about calculating the Ethernet MAC on platforms with no built-in
Ethernet, and removes documentation for esp_efuse_mac_get_custom() on targets
other than ESP32
