This commit deprecates the "freertos/xtensa_timer.h" and "xtensa/xtensa_timer.h"
include paths. Users should use "xtensa_timer.h" instead.
- Replace legacy include paths
- Removed some unnecessary includes of "xtensa_timer.h"
- Add warning to compatibility header
modem retention: Support esp32c6 wifi MAC and baseband sleep retention
sleep_modem: wifi MAC modem wakeup protect in modem state before PMU trigger sleep enable request
sleep modem: provide a interface to get whether the Modem power domain is allowed to power off during sleep
add i2c_ana master header file to project
auto beacon: release PMU's lock on root clock source (it is locked in the PLL)
wifi receiving beacon frame in PMU modem state strongly depends on the BBPLL
clock, PMU will forcibly lock the root clock source as PLL, when the root
clock source of the software system is selected as PLL, we need to release
the root clock source locking.
When it is judged that the PLL is locked by PMU after wakeing up from the PMU
modem state, switch the root clock source to the PLL in the sleep process (a
critical section).
auto beacon: fix the failure to receive broadcast/multicast frames in modem state
When the multicast field in the beacon frame received in the PMU modem state is
True, the PMU switches to the PMU active state (the PMU waits for the HP LDO to
stabilize and then restores the MAC context) and starts to receive
broadcast/multicast frames (Broadcast/Multicast frames will be sent after a
minimum delay of 48 us after the beacon frame), because the PMU waits for the HP
LDO to stabilize too long (~154 us), which will cause broadcast/multicast frame
reception to be missed.
auto beacon: select the PLL clock source as the REGDMA backup clock source when the PMU switches to ACTIVE from MODEM state
update Digital Peripheral (M2A switch) REGDMA restore time parameter
auto beacon: fix the issue that only channel 1 can connect to AP in modem state
Before this fix, when we call esp_pm_configure after gpio_wakeup_enable,
the configuration of GPIO in sleep state in gpio_wakeup_enable will be
overwritten by esp_pm_configure.
This commit marks all functions in interrupt_controller_hal.h, cpu_ll.h and cpu_hal.h as deprecated.
Users should use functions from esp_cpu.h instead.
The behavior of portSET_INTERRUPT_MASK_FROM_ISR() has changed in SMP FreeRTOS. It's
previous behavior is now implemented in portDISABLE_INTERRUPTS() and portRESTORE_INTERRUPTS().
This commit replaces all portSET_INTERRUPT_MASK_FROM_ISR() and portCLEAR_INTERRUPT_MASK_FROM_ISR()
calls with portDISABLE_INTERRUPTS() and portRESTORE_INTERRUPTS() respectively
Moved the following kconfig options out of the target component:
* CONFIG_ESP*_DEFAULT_CPU_FREQ* -> esp_system
* ESP*_REV_MIN -> esp_hw_support
* ESP*_TIME_SYSCALL -> newlib
* ESP*_RTC_* -> esp_hw_support
Where applicable these target specific konfig names were merged into
a single common config, e.g;
CONFIG_ESP*_DEFAULT_CPU_FREQ -> CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ
1. Clean up clk usage in IDF, replace rtc_clk_xtal/apb_freq_get with
upper level API esp_clk_xtal/apb_freq
2. Fix small errors and wrong comments related to clock
3. Add clk_tree_defs.h to provide an unified clock id for each chip
Modify the NGed drivers to adopt new clock ids
This commit removes the following critical nested macros as follows:
- portENTER_CRITICAL_NESTED()
- portEXIT_CRITICAL_NESTED()
They are replaced with portSET_INTERRUPT_MASK_FROM_ISR() and
portCLEAR_INTERRUPT_MASK_FROM_ISR() which are the proper FreeRTOS interfaces.
Created a portmacro_deprecated.h for each port to contain deprecated API
that were originally from portmacro.h
