1. Use BIT[7:5] of EID to determine psram size
2. Add ID support for 16Mbit psram
3. Remove module reset on SPI1
4. Confirmed with the vendor that only the old 32Mbit psram need special clock timing. For other psram chips, we should use standard QPI mode.
1. add network channel switch function.
- users can obtain the new channel through the event MESH_EVENT_CHANNEL_SWITCH.
- the entire network will be moved to the same channel as the router without user intervention.
- if no router is in the network, users can call esp_mesh_switch_channel() on the root side to
move the entire network to their desired channel.
2. support not configuring the network channel.
3. support not configuring the router BSSID even if the router is hidden.
4. add allow_channel_switch to mesh configuration.
- if the channel is not specified, this value will be ignored.
- if the channel is specified and this value is set, when "fail" (mesh_attempts_t) times of parent selection
or look for networks are reached, device will change to perform a full channel scan for networks that could join.
- if the channel is specified and this value is set to 0, when a root is not elected, channel switch is not allowed.
but when a root appears, the root performs a full channel scan during the process of connecting to the router,
so even allow_channel_switch is set to 0, the root may still switch channel and eventually the entire network
changes channel.
5. add allow_router_switch to mesh router configuration.
- if the BSSID of router is not specified, this value will be ignored.
- if the BSSID of router is specified and this value is set, when the router of this specified BSSID fails to be found
after "fail" (mesh_attempts_t) times, the entire network is allowed to switch to another router with the same SSID.
6. modify the root to perform a full channel scan when esp_wifi_connect().
7. support handling beacon without DS Paramter Set.
The DMA cannot receive data correctly when the buffer address is not
WORD aligned. Currently we only check whether the buffer is in the DRAM
region.
The DMA always write in WORDs, so the length arguments should also be
multiples of 32 bits.
A check is added to see whether the buffer is WORD aligned and has valid
length.
The driver decide whether use MOSI/MISO phases according to the buffer
address together with the SPI_TRANS_USE_*DATA. However someone may assue
that these phases will be skipped when the ``length``/``rxlength`` is
set to 0. In fact it is a feature that ``rxlength`` is allowed to be
set to 0 when tx and rx have the same length, and the driver fill the
``rxlength`` to ``length``.
An error check is added when the rxlength is 0 but there is data to be
sent.
It has been observed that, in case of underflow (data unavailability) in
I2S transmission, previously filled up tx descriptors continue to get
transmitted on line, causing noise in case of audio use case.
This change adds optional `tx_desc_auto_clear` field during I2S driver intialization
than can zero initialize tx descriptor in case of underflow situation in
interrupt handler itself.
Closes: https://github.com/espressif/esp-idf/issues/1789
Fix some WiFi bugs:
1. Enable RX BAR
2. Fix the bug that ESP32 AP negotiates with iphone to 11g
3. Fix the bug that ESP32 STA has ap_loss because CMCC AP contains two SSID
Don’t allow the compiler to convert malloc + memset into calloc,
causing a recursive call in _calloc_r. Fixes crash when building with
-O2 optimization level.
1. fix failture of mesh stop caused by block-sending.
2. fix when FIXED_ROOT is set, 2nd layer devices can not receive mesh event ESP_ERR_MESH_NO_PARENT_FOUND.
3. fix when FIXED_ROOT is set and the root turns off mesh function, 2nd layer devices do not look for new parents.
4. add APIs esp_mesh_disconnect() and esp_mesh_connect().
5. disconnect from parent/router when the DSSS channel in received beacon is different from the home channel.
6. remove nvs task to release 3k bytes memory.
Introduced in 9c23b8e5 and 4f87a62f. To get higher speed, menuconfig
options are added to put ISR and other functions into the IRAM. The
interrupt flag ESP_INTR_FLAG_IRAM is also mistakenly set when the ISR is
put into the IRAM. However callbacks, which are wrote by the user, are
called in the master and slave ISR. The user may not be aware of that
these callbacks are not disabled during flash operations. Any cache miss
during flash operation will cause panic.
Essentially IRAM functions and intrrupt flag ESP_INTR_FLAG_IRAM are
different, the latter means not disabling the ISR during flash
operations. New bus_config flag intr_flags is offered to help set the
interrupt attribute, including priority level, SHARED, IRAM (not
disabled during flash operations). It introduced a small BREAK to
IDFv3.1 (but the same as IDFv3.0) that the user has to manually set IRAM
flag now (therefore he's aware of the IRAM thing) to void the ISR being
disabled during flash operations.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
New unity component can be used for testing other applications.
Upstream version of Unity is included as a submodule.
Utilities specific to ESP-IDF unit tests (partitions, leak checking
setup/teardown functions, etc) are kept only in unit-test-app.
Kconfig options are added to allow disabling certain Unity features.
transport_mode accepts enum httpd_ssl_transport_t instead of true/false.
This will allow for extension to dual mode (server running on both secure and insecure ports) in the future.
* http_sess_set_*_override APIs are now the only ones available to set custom recv/send/pending functions
* Fixed side effects to using http_sess_set/get_context inside URI handlers
Changes:
- renamed `httpd_free_sess_ctx_fn_t` to `httpd_free_ctx_fn_t`
- added a `httpd_handle_t` argument to `httpd_send_func_t` and `httpd_recv_func_t`
- internal function `httpd_sess_get()` is no longer static, as it's used in other
files besides httpd_sess.c
Bug fixes:
- removed a trailing semicolon from `HTTPD_DEFAULT_CONFIG()`
- fixed issue with failed `select()`, now it automatically closes invalid sockets
instead of shutting down the entire server
New features:
- `httpd_resp_send()` and `httpd_resp_send_chunk()` now accept -1 as length to use
`strlen()` internally
- added `httpd_sess_set_ctx()` to accompany `httpd_sess_get_ctx()`
- added a "transport context" to the session structure (next to user context)
- added `httpd_sess_{get,set}_transport_ctx()` to work with this transport context
- added "global user context" and "global transport context" stored in the server
config (and then the handle); supports a user-provided free_fn
- added a "pending func" to e.g. check for data in the transport layer receive
buffer
- added functions `httpd_set_sess_{send,recv,pending}_override()` that target
a session by ID (i.e. not using a request object)
- added `httpd_set_pending_override()`
- added a "open_fn" and "close_fn" - functions called when creating and closing
a session. These may be used to set up transport layer encryption or some other
session-wide feature
Background
Softap will send connected event after receive assoc request as before, however, STA didn't connect to softAP if need security. As our mesh design, it will send data packet after receive connected event, so change the current behavior, softAP will send connected event if have encryption
Support for HSPI to output clock for 4M SPIRAM introduced regression
in clock configuration affecting SPIRAM access with 80MHz clock. This
commit fixes the issue.
1. call esp_timer_get_time and ref_clock_get in the same order on
start and in the loop
2. disable interrupts when calculating delta between ref_clock
and esp_timer
3. ensure both functions are in cache before calculating the delta
mdns queries did not work properly when send imeadiately after set_hostname, which cuased reinit of pcb and therefore restarted probing, so search packets were blocked until probing finished
closes#2507, closes#2593
1. Fix the bug that disable controller suddenly cause crash when ble is working. (585cfba1)
2. Fix the bug that when disable controller, it will cause wifi cannot RX, TX timeout, buffer lack and etc. (f8546145)
It is an ESP specific FreeRTOS feature that the ISR is always executed
on the core which calls the interrupt register function. In the SPI
driver, the function is always called in the bus initialization
function.
Hence, the ISR will be executed on the core which initialize the driver.
If the core is starved due to higher priority ISRs, or the interrupt is
disabled on the core (spinlock called, etc.), the ISR will not get
executed and SPI transactions will not be handled.
(MINOR CHANGE)
Resolves https://github.com/espressif/esp-idf/issues/2432.
The MISO signal will be delayed if the GPIO matrix is enabled.
However, delay also comes from the slave.
Previous code only considers the former case, and assume the frequency
limitations is only violated when GPIO matrix is used.
Now we are able to calculate the freq limit when extenal MISO delay is
given (feature introduced in 9c6c6ec34ab0641ace89aeb9b1a133eb6fae1a18).
The frequency limit is lower when the external MISO delay is large, and
the limit is likely to be violated even with IOMUX.
Resolves https://github.com/espressif/esp-idf/issues/2690.
1. If L2_TO_L3_RX_BUF_MODE is not selected, we must assign l2_owner explictly before we call pbuf_free.
2. free intr resource in esp_eth_deinit
Closes https://github.com/espressif/esp-idf/issues/2670
1. fix ap_loss that occurs when the parent turns off the mesh function and becomes a normal WiFi with a different SSID.
2. add an event MESH_EVENT_NETWORK_STATE that contains information about whether there is a root in the current network.
3. modify the mechanism of mesh IE update.
4. fix a problem in the process of re-voting to select the root, the device that does not meet the conditions of being a root votes for itself.
5. fix an issue that occurs in esp_mesh_recv_toDS() when stopping the mesh.
6. when the user specifies a parent for the device, the device will set the authmode and password of its AP mode to the same value as the specified parent.
7. add two disconnected reason codes MESH_REASON_EMPTY_PASSWORD and MESH_REASON_PARENT_UNENCRYPTED.
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
When light sleep is finished on one CPU, it is possible that the other
CPU will enter light sleep again very soon, before interrupts on the
first CPU get a chance to run. To avoid such situation, set a flag
for the other CPU to skip light sleep attempt.
Tickless idle/light sleep procedure had a bug in single core mode.
Consider the flow of events:
1. Idle task runs and calls vApplicationIdleHook
2. This calls esp_vApplicationIdleHook, which calls esp_pm_impl_idle_hook, and pm lock for RTOS on the current core is released.
3. Then esp_vApplicationIdleHook calls esp_pm_impl_waiti, which checks that s_entered_light_sleep[core_id]==false and goes into waiti state.
4. Some interrupt happens, calls esp_pm_impl_isr_hook, which takes pm lock for RTOS. PM state goes back to CPU_FREQ_MAX.
5. Once the interrupt is over, vApplicationIdleHook returns, and Idle task continues to run, finally reaching the call to vApplicationSleep.
6. vApplicationSleep does not enter light sleep, because esp_pm_impl_isr_hook has already changed PM state from IDLE to CPU_FREQ_MAX.
This didn’t happen in dual core mode, because waiti state of one CPU was interrupted by CCOMPARE update interrupt from the other CPU, in which case PM lock for FreeRTOS was not taken.
Fix by inverting the meaning of the flag (for convenience) and only setting it to true when vApplicationSleep actually fails to enter light sleep.
Having two different spinlocks is problematic due to possibly
different order in which the locks will be taken. Changing the order
would require significant restructuring of kernel code which is
undesirable.
An additional place where taking xTickCountMutex was needed was in
vApplicationSleep function. Not taking xTickCountMutex resulted in
other CPU sometimes possibly advancing tick count while light sleep
entry/exit was happening. Taking xTickCountMutex in addition to
xTaskQueueMutex has shown a problem that in different code paths,
these two spinlocks could be taken in different order, leading to
(unlikely, but possible) deadlocks.
1. When WIFI task or other high priority task blocks the Bluetooth task, ACL RX buffer will use up, ACL RX buffer ptr will point to null and will never point to a valid adress. Causing errors in Bluetooth.
2. hcimsgs.h used whether flow control is on or off
Introduced in 97e3542947.
The previous commit frees the IRAM part when single core, but doesn't
change the memory layout functions. The unit test mallocs IRAM memory
from the heap, accidently into the new-released region, which doesn't
match the memory layout function.
This commit update the memory layout function to fix this.
Problem Decribe
The problem happenned when do wps with a mikrotik router
1. router always want to do connect with 32 without EAP-WSC step
2. after 4 way timeour, 32 crash
Root Cause
The reason why can not start EAP-WSC step is router's check method is RSN > WPA > WPS, when it found there include RSN and WPS in assoc, it will choice do 4 way rather than WPS
The reason of second problem is 32's EAPOL start timer didn't stop and send EAPOL start to a null pointer
Soultion
1. remove RSN and WPA ie when do WPS step
2. check mac address's pointer before send EAPOL start
closes: https://github.com/espressif/esp-idf/issues/2382
Fix following WiFi bugs:
1. Fix the bug that MIC verification fails on soft-AP mode
2. Modify mesh root to have same behavior as normal WiFi STA in state change
3. Fix the bug that sniffer can't catch control packets
4. Fix crash bug in soft-AP mode
5. Fix ACM(Admission Control Management) bug
1) two events AP_STOP, AP_START shortly after each other may cause IGMP config on already stopped netif
2) not properly locked sending packets to queue from timer task
closes#2580
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
In earlier change this component was decoupled from freertos and hence
regression was introduced which changed default placement to flash. Some
device drivers make use of ringbuffer while flash cache is being disabled
and hence default placement should instead be internal memory.
Closes: https://github.com/espressif/esp-idf/issues/2517
1. fix some bugs by previous coex hw blocking bugfix,
such like, rwble.c (64, 0) line 222
2. fix bug that ble scan performance is very low when software coexist
is working.
3. update libcoexist version to v1.1.0
This feature allows `httpd_req_recv()` and `httpd_send()` functions to return
specific `HTTPD_SOCK_ERR_` codes in case of socket errors. This is useful
in case of errors like `EAGAIN`, `EINTR`, etc. when the user may want to
retry `httpd_req_recv()` / `httpd_send()` function call.
This example adds functionality to support basic communication in RS485 networks using Modbus protocol.
This example uses FreeModbus stack and regular UART driver API to communicate in RS485 half duplex mode.
Added initial support of modbus controller pure C api to access device parameters over Modbus transport.
Move freemodbus stack and port files into components folder
Move the modbus_controller interface into components idf folder
Source files updated after review.
Add modbus interface documentation docs/en/api-reference/protocols/modbus.rst
porttimer.c: fix bug with timer1 selected in the Kconfig
Add support of cmake system (added cmake files)
Closes https://github.com/espressif/esp-idf/issues/858
In some cases, when data was just written into UART FIFO, transmitter
state could be still zero while the FIFO did contain some data.
This resulted in uart_tx_wait_idle occasionally returning before all
the data was sent out.
Fix by checking both UART transmitter state and TX FIFO count.
ROM definition of `abort` was removed in 9240bbb. The old definition
resulted in a panic due to a jump to a null pointer (abort member in
ROM stub table was zero). The new definition triggers a debug
exception if JTAG is connected, or goes into an infinite loop to be
reset by the WDT.
Some logging done in soc component may happen before logging via
stdout is possible. Use _EARLY version of log calls to make sure that
output is visible. The downside is that application does not have a
way to silence these logs. However since the soc component doesn’t
use any LOGV/LOGD/LOGI and only logs warnings and errors, this should
not impact the application.
This commit updates some of the API references in task.h so
that stack sizes are referred to in bytes rather than words as
found in the vanilla version.
Closes#2528
1. Fix the bug that ESP32 will reject the retry AddBA request frame
if AddBA response frame is failed to sent by WiFi LMAC
2. Fix the bug that AddBA request retrys too frequently
3. Forbid BA session setup for VO queue related TID
1. remove use EID to distinguish psram voltage
2. 1V8 64Mbit psram and 3V3 64Mbit psram use the same psram driver(standard spi interface)
3. set cs hold time register as 1
Content-Length header should not be included when using chunked encoding.
Some browsers will close the socket after seeing the 0 sized response instead of
reading the chunks.
Merges https://github.com/espressif/esp-idf/pull/2458
1. Add command for Ethernet based on console component.
2. Make cmd_system and iperf a component that can be referenced by other examples
3. Add "version" command to cmd_system.c
4. Clean up the README.md in all ethernet examples[TW#26525]
Added a new API esp_tls_set_global_ca_store(esp_tls_cfg_t *cfg) which creates a global_cacert which can be used by multiple connections by setting the use_global_ca_store variable to true in their respective structure of esp_tls_cfg_t. Also changed the cacert in the structure of esp_tls_t to a pointer.
* BLE and softAP provisioning examples added along with tests.
* An application specific example added for demonstrating custom provisioning scheme.
* tools/esp_prov/esp_prov.py can be used as a provisioning client for SoftAP, BLE and CLI based transports.
Co-Authored-By: Amey Inamdar <amey@espressif.com>
Co-Authored-By: Anurag Kar <anurag.kar@espressif.com>
* This manages secure sessions and provides framework for multiple transports.
* The application can use protocomm layer directly to have application specific extensions for provisioning (or non-provisioning) use cases.
* Following features are available for provisioning :
* Security - Security0 (no security), Security1 (curve25519 key exchange + AES-CTR encryption)
* Proof-of-possession support for Security1
* Protocomm requires specific protocol buffer modules for compilation which can be generated from the `.proto` files in the `proto` directory using make.
Co-Authored-By: Amey Inamdar <amey@espressif.com>
Co-Authored-By: Anurag Kar <anurag.kar@espressif.com>
tcp_transport component used public header files such as 'transport.h', etc. which are too generic and might collide with user or user libraries headers
This change closes#2417
In some cases, linker could choose to use ROM functions instead of the
ones defined in IDF.
For functions used in ROM stub table, this would lead to infinite
recursion when the corresponding function was called from ROM.
For crypto functions, some of these were modified in IDF, and
incompatible with ROM counterparts.
Problem Description
The reporduce steps are as follows:
1. put more than one same ssid AP in the environment;
2. set the STA mac address in one of the APs blacklist, and make sure the AP is closest to STA;
3. set the scan method in station config as all channel scan;
4. try to connect the AP which set STA in blacklist
Phenmenon
STA fail to connect after send auth or assoc with a wrong status code, but no disconnect event report and can not connect the next one in the envrionment
Root Cause
Because there are some same ssid APs in the evnrionment, when do all channel scan, it will collect all the matched AP in rc list, because rc list is not empty, so it would send disconnect event, however, we didn't do other step such as connect to other one
VNC MR 570
closes https://github.com/espressif/esp-idf/issues/2323
_rtc_data_{start,end} can now describe data placed into RTC_FAST
segment, if CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled.
Use new _rtc_slow_length symbol instead.
When CONFIG_ESP32_RTCDATA_IN_FAST_MEM is enabled, RTC data is placed
into RTC_FAST memory region, viewed from the data bus. However the
bootloader was missing a check that this region should not be
overwritten after deep sleep, which caused .rtc.bss segment to loose
its contents after wakeup.
fix the bug following:
1. after disable bluetooth controller, wifi cannot TX/RX any packets.
2. when software coexist working, there's a little ratio cause wifi task watchdog timeout
3. when software coexist working, there's a little ratio cause bluetooth cannot receive anything.
feature:
1. add libbtdm_app.a git commit local and remote checking
Known issues:
1. there's still a bug occurs with a very very low ratio cause bluetooth
cannot receive anything. The reproduce interval may great than 3days ~ 1week via
7x24 hours heavy testing.
Previously, esp-touch only supports multicast packets which are
transmitted from cellphone. But for most dual frequency routers
whose SSIDs of 5G and 2.4G are the same, broadcast packets are
forwarded from 5G interface to 2.4G interface while multicast
packets are not. In order to make esp-touch work when cellphone
connects to 5G interface of these routers, esp-touch is improved
to support both multicast and broadcast packets. Meanwhile, new
APP which is compiled with Andriod or IOS library(>= v0.3.6.2)
must be used in this situation. Note that for some routers,
broadcast and multicast packets are forwarded from 5G interface
to 2.4G interface only when another WiFi device is connected to
2.4G interface of the router. Old APP which is compiled with
Android or IOS library(< v0.3.6.2) also works with this improvement
when cellphone connects to 2.4G interface of the router.
The Android and IOS library of new esp-touch APP is now available
on Github.
Android: https://github.com/EspressifApp/EsptouchForAndroid
IOS: https://github.com/EspressifApp/EsptouchForIOS
Four internal APIs `esp_http_client_connect()`, `http_client_prepare_first_line()`, `esp_http_client_request_send()` and
`esp_http_client_send_post_data()` API have been added for perfoming connection establishment (sync as well as async),
preparing first line, sending request and sending post data respectively.
In `transport_ssl`, `ssl_connect_async()` API has been added for establishing asynchronous connection.
1. suppport mesh type, mesh ID, router and IE crypt func&key at any time after mesh is initalized.
2. support modify parent at any time after mesh is configured.
3. modify manual networking example.
4. update header file.
5. fix issues in root conflicts handling.
6. add max length of beacon to menuconfig.
7. fix issue when received a beacon without DSSS.
This introduces the following changes :
* Implmentation added for pthread attribute related functions :
* pthread_attr_init
* pthread_attr_destroy
* pthread_attr_setdetachstate
* pthread_attr_getdetachstate
* pthread_attr_getstacksize
* pthread_attr_setstacksize
* pthread_create now supports passing attributes/configs through pthread_attr_t structure
* pthread_mutex_timedlock added
* pthread_exit added
* memory for joinable thread is freed before returning from pthread_join
Problem Description
set some of routers as the same ssid in the same channel, when 32 in the fast scan connect mode, there may no disconnect event report in that two sceanrio:
1. set the correct password and connect, if target router didn't report 32's auth req before timeout, the state machine change to init but no disconnect event report
2. set a wrong password, if router send disassoc or deauth after run, rather than wait 4 way handshake timeout, the state machine change to init but no disconnect event report
Root Cause
Because the routers are in the same channel, all of them are matched the ssid, so all of them can be instore in the rc list wait for connect, when the first one want to connect fail at auth or receive
disassoc or deauth when password wrong, the rc list is not empty, it can not send disconnect event because rc is not empty
Solution
1. put the fail the router in the blacklist
2. Judge whether there is another router can be connect, if it has, try to connect with the next one
VNC MR 561
gen_esp_err_to_name.py includes files like
components/lwip/include/apps/esp_ping.h as "apps/esp_ping.h" because all
subdirectories of "include" are used. If "components/lwip/include/apps"
is in the path of the compiler instead of "components/lwip/include" then
include "apps/esp_ping.h" will fail. This fix allows to process lines
like:
'// gen_esp_err_to_name.py: some text "esp_ping.h" some text'
in header files for overwriting the include.
Before LwIP was moved into a submodule, sntp and esp_ping were
available as the following includes:
#include "apps/sntp/sntp.h"
#include "esp_ping.h"
This commit makes header files available at the old location, and adds
a deprecation warning for sntp.h.
Closes https://github.com/espressif/esp-idf/issues/2392
The lwip code didn't create an new mld group when netif is up,
this will lead to the server can't find the matching netif when
receiving NS(neighbor solicitation) packet
If exception support is disabled in IDF, and libstdc++ tries to throw
an exception, it will call __cxa_allocate_exception which is replaced
with abort in IDF.
We have a dramatically size reduction of the RO-section in binary when using '__throw_'-stubs in GCC5
In the case of using GCC8, we are faced with 'multiple definition' errors when using '__throw_'-stubs.
Good that we don't have the size problem due to gcc8
If CONFIG_FREERTOS_LEGACY_HOOKS is kept enabled then defining
idle/tick hooks will be applications responsibility as was the
case earlier.
Signed-off-by: Mahavir Jain <mahavir@espressif.com>
1. create a new pbuf to squash linked pbuf
2. optimize emac driver by adding ESP_IRAM_ATTR
3. remove duplicated function declare in esp_eth.h
4. remove duplicated code in emac_setup_tx_desc
5. disable Promiscuous mode
1. Keep awake to receive beacon at TBTT time no matter which state
station is on.
2. If there is any packet to send on dream or sleep state, send NULL
data with power save bit clear first.
This commit adds an option to enclose all FreeRTOS task functions within a
wrapper function. In the case that a task function returns, the wrapper function
will log an error and abort the application immediately.
Closes#2269Closes#2300
refence to https://github.com/espressif/esp-idf/issues/2284
Before fixing, the tx power in adv data is always 0xeb(-21dbm).
restriction:
If change BLE advertising TX power, please call esp_ble_gap_config_adv_data()
after BLE adv TX power changed.
Later, will implement set BLE advertising TX power via HCI, then the
TX power value in adv data can be update automatically after BLE adv
TX power changed.
Changes:
KConfig: The option CONFIG_ESP32_RTCDATA_IN_FAST_MEM is added in Kconfig file for esp32 component.
esp32.common.ld: added support of RTC_DATA_ATTR, RTC_RODATA_ATTR data placement into appropriate segment according to Kconfig option.
esp32.ld: linker script is modified to set alias for memory segment selected by Kconfig option to place data. The segments for force placement are added for RTC_FAST_ATTR, RTC_SLOW_ATTR attributes.
esp_attr.h: added new attributes RTC_FAST_ATTR, RTC_SLOW_ATTR for force placement into fest/slow memory.
test_rtc_fast.c: Added unit test cases to check data placement into appropriate memory segment.
Updated documentation for RTC_DATA_ATTR, RTC_FAST_ATTR, RTC_SLOW_ATTR in deep_sleep_stub.rst file.
TW#18001
Closes https://github.com/espressif/esp-idf/issues/1553
