This commit deprecates the "freertos/xtensa_context.h" and "xtensa/xtensa_context.h"
include paths. Users should use "xtensa_context.h" instead.
- Replace legacy include paths
- Removed some unnecessary includes of "xtensa_api.h"
- Add warning to compatibility header
This commit deprecates the "freertos/xtensa_api.h" and "xtensa/xtensa_api.h"
include paths. Users should use "xtensa_api.h" instead.
- Replace legacy include paths
- Removed some unnecessary includes of "xtensa_api.h"
- Replaced some calls with "esp_cpu_..." equivalents
- Add warning to compatibility header
Common spi functionality for sharing the SPI bus between modules is moved from esp_driver_spi to
a more fitting location in esp_hw_support (shared HW resource control).
This also allows us to decouple the spi_flash driver from esp_driver_spi, removing
esp_driver_spi and esp_ringbuf from G1 builds.
Now the soc interrupts definitions are scattered around in the esp-idf
which are out of sync. Put interrupts definitions in soc/periph_defs.h
(!ESP32) or soc/soc.h(ESP32) together in soc/interrupts.h.
If the TimerGroup 0 clock is disabled and then reenabled, the watchdog
registers (Flashboot protection included) will be re-enabled, and some
seconds later, will trigger an unintended reset.
Signed-off-by: Gustavo Henrique Nihei <gustavo.nihei@espressif.com>
1. Remove RTC_CLOCK_BBPLL_POWER_ON_WITH_USB Kconfig option
During sleep, BBPLL clock always gets disabled
esp_restart does not disable BBPLL clock, so that first stage bootloader log can be printed
2. Add a new Kconfig option PM_NO_AUTO_LS_ON_USJ_CONNECTED
When this option is selected, IDF will constantly monitor USB CDC port connection status.
As long as it gets connected to a HOST, automatic light-sleep will not happen.
Closes https://github.com/espressif/esp-idf/issues/8507
This commit marks all functions in interrupt_controller_hal.h, cpu_ll.h and cpu_hal.h as deprecated.
Users should use functions from esp_cpu.h instead.
Moved the following kconfig options out of the target component:
* CONFIG_ESP*_DEFAULT_CPU_FREQ* -> esp_system
* ESP*_REV_MIN -> esp_hw_support
* ESP*_TIME_SYSCALL -> newlib
* ESP*_RTC_* -> esp_hw_support
Where applicable these target specific konfig names were merged into
a single common config, e.g;
CONFIG_ESP*_DEFAULT_CPU_FREQ -> CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ
Moved the following kconfig options out of the target component:
* ESP32_X_BROWNOUT_* -> esp_system
* ESP32_X_DEBUG_OCDAWARE -> esp_system
* APP_NO_BLOBS -> build type (main kconfig)
Upstream xtensa exception handling will save PS, PC, and a0 registers
together when saving a minimal context. This commit ppdates the xtensa
exception handling to match upstream behavior.
The following files were deleted:
- components/esp_hw_support/include/soc/cpu.h
- components/soc/esp32s3/include/soc/cpu.h
The following functions are deprecated:
- get_sp()
The following functions declared in soc/cpu.h are now moved to esp_cpu.h:
- esp_cpu_configure_region_protection()
The following functions declared in soc/cpu.h are now moved to components/xtensa/include/esp_cpu_utils.h:
- esp_cpu_process_stack_pc()
All files with soc/cpu.h inclusion are updated to include esp_cpu.h instead.
Signed-off-by: Sudeep Mohanty <sudeep.mohanty@espressif.com>
peripheral enable/disable usually should be managed by driver itself,
so make it as espressif private APIs, not recommended for user to use it
in application code.
However, if user want to re-write the driver or ports to other platform,
this is still possible by including the header in this way:
"esp_private/peripheral_ctrl.h"
As branches/jumps on Xtensa have a maximum range for the destination, it is
unsafe to refer to a label to another compilation unit in a branch/jump instruction.
The labels have been replaced by absolute addresses.
