The DMA cannot receive data correctly when the buffer address is not
WORD aligned. Currently we only check whether the buffer is in the DRAM
region.
The DMA always write in WORDs, so the length arguments should also be
multiples of 32 bits.
A check is added to see whether the buffer is WORD aligned and has valid
length.
The driver decide whether use MOSI/MISO phases according to the buffer
address together with the SPI_TRANS_USE_*DATA. However someone may assue
that these phases will be skipped when the ``length``/``rxlength`` is
set to 0. In fact it is a feature that ``rxlength`` is allowed to be
set to 0 when tx and rx have the same length, and the driver fill the
``rxlength`` to ``length``.
An error check is added when the rxlength is 0 but there is data to be
sent.
It has been observed that, in case of underflow (data unavailability) in
I2S transmission, previously filled up tx descriptors continue to get
transmitted on line, causing noise in case of audio use case.
This change adds optional `tx_desc_auto_clear` field during I2S driver intialization
than can zero initialize tx descriptor in case of underflow situation in
interrupt handler itself.
Closes: https://github.com/espressif/esp-idf/issues/1789
Introduced in 9c23b8e5 and 4f87a62f. To get higher speed, menuconfig
options are added to put ISR and other functions into the IRAM. The
interrupt flag ESP_INTR_FLAG_IRAM is also mistakenly set when the ISR is
put into the IRAM. However callbacks, which are wrote by the user, are
called in the master and slave ISR. The user may not be aware of that
these callbacks are not disabled during flash operations. Any cache miss
during flash operation will cause panic.
Essentially IRAM functions and intrrupt flag ESP_INTR_FLAG_IRAM are
different, the latter means not disabling the ISR during flash
operations. New bus_config flag intr_flags is offered to help set the
interrupt attribute, including priority level, SHARED, IRAM (not
disabled during flash operations). It introduced a small BREAK to
IDFv3.1 (but the same as IDFv3.0) that the user has to manually set IRAM
flag now (therefore he's aware of the IRAM thing) to void the ISR being
disabled during flash operations.
New unity component can be used for testing other applications.
Upstream version of Unity is included as a submodule.
Utilities specific to ESP-IDF unit tests (partitions, leak checking
setup/teardown functions, etc) are kept only in unit-test-app.
Kconfig options are added to allow disabling certain Unity features.
It is an ESP specific FreeRTOS feature that the ISR is always executed
on the core which calls the interrupt register function. In the SPI
driver, the function is always called in the bus initialization
function.
Hence, the ISR will be executed on the core which initialize the driver.
If the core is starved due to higher priority ISRs, or the interrupt is
disabled on the core (spinlock called, etc.), the ISR will not get
executed and SPI transactions will not be handled.
(MINOR CHANGE)
Resolves https://github.com/espressif/esp-idf/issues/2432.
The MISO signal will be delayed if the GPIO matrix is enabled.
However, delay also comes from the slave.
Previous code only considers the former case, and assume the frequency
limitations is only violated when GPIO matrix is used.
Now we are able to calculate the freq limit when extenal MISO delay is
given (feature introduced in 9c6c6ec34ab0641ace89aeb9b1a133eb6fae1a18).
The frequency limit is lower when the external MISO delay is large, and
the limit is likely to be violated even with IOMUX.
Resolves https://github.com/espressif/esp-idf/issues/2690.
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
This commit does the following
- Add power management lock to CAN driver so that APB frequency does not change
whilst CAN driver is in use
- Fix incorrect flag in can_transmit()
- Refactor can_driver_install() and can_driver_uninstall() so that critical sections
are shorter
- Fix CAN gpio configuration bug on RX pin. Closes#2302
- Add docs about multiple ID configuration and fix example links
Works for 3.3V eMMC in 4 line mode.
Not implemented:
- DDR mode for SD cards (UHS-I) also need voltage to be switched to 1.8V.
- 8-line DDR mode for eMMC to be implemented later.
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.
Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
The test is previously disabled for the requirement of external
connection. Now the signals are connected by internal connections.
Also change the failure logic of the test.
Perviously host send_auto_stop flag would be set for every data
transfer over 1 block long. This caused stop commands to be sent
after CMD53, which shouldn't be done. Fix by adding an explicit list
of commands for which send_auto_stop should be set.
