Set max TLS version in the SSL context during setup phase. Dynamic
buffer feature overrides the `mbedtls_ssl_setup` API and hence
this change is required per upstream 3.5.0 codebase change.
Add changes to use fast_pbkdf2 as default for PMK calculations.
fast_pbkdf2 is significantly faster than current implementations
for esp chips.
Also removes unnecessary code for pbkdf-sha256 and pbkdf-sha512.
Updates config to define the new MBEDTLS_SSL_CID_TLS1_3_PAD_GRANULARITY
option, which replaced the previously used
MBEDTLS_SSL_CID_PADDING_GRANULARITY. The old option is continuing to be
used as the new one exceeds the maximum length for an option name in
esp-idf.
See https://github.com/Mbed-TLS/mbedtls/pull/4490 for more information.
Signed-off-by: Daniel Mangum <georgedanielmangum@gmail.com>
For certain data lengths, the last input descriptor was not getting appended
correctly and hence the EOF flag in the DMA descriptor link list was
set at incorrect location. This was resulting in the peripheral being
stalled expecting more data and eventually the code used to timeout
waiting for the AES completion interrupt.
Required configs for this issue:
CONFIG_MBEDTLS_HARDWARE_AES
CONFIG_SOC_AES_SUPPORT_DMA
This observation is similar to the issue reported in:
https://github.com/espressif/esp-idf/issues/10647
To recreate this issue, start the AES-GCM DMA operation with data length
12280 bytes and this should stall the operation forever.
In this fix, we are tracing the entire descriptor list and then appending the
extra bytes descriptor at correct position (as the last node).
DMA operation completion must wait until the last DMA descriptor
ownership has been changed to hardware, that is hardware is completed
the write operation for entire data. Earlier for the hardware GCM case,
the first DMA descriptor was checked and it could have resulted in some
race condition for non interrupt (MBEDTLS_AES_USE_INTERRUPT disabled) case.
SHA hardware DMA mode calculation had off-by-one error for specific
input lengths. This was causing last chunk of the input data not being
fed to the hardware accelerator and hence resulting in an incorrect
final result.
Closes: https://github.com/espressif/esp-idf/issues/11915
- Earlier, some intermediate return values were not stored and returned,
thus incorrect return values used to get transmitted to the upper layer of APIs.
- Also, zeroised the output buffer in case of error condition.
Fix build issue in mbedTLS dynamic buffer feature with
`CONFIG_MBEDTLS_DHM_C` enabled case. Also added a build
configuration for the test coverage.
Closes https://github.com/espressif/esp-idf/issues/11770
The number of the DMA descriptors allocated for certain length (e.g.,
8176) were not sufficient (off by 1 error). This used to result in the
dynamic memory corruption as the region was modified beyond the
allocated range.
This change fixes the DMA descriptor calculation part and allocates
sufficient DMA descriptors based on the data length alignment considerations.
Test has also been added to cover the specific scenario in the CI.
Closes https://github.com/espressif/esp-idf/issues/11310
- Use DPORT_WRITE_REG (volatile writes) wrappers to write to the
MPI peripheral
- Updated the previous workaround added for the same issue as it
was failing in some long runs and with `COMPILER_OPTIMIZATION_PERF`
enabled.
- The test performance numbers had to be updated due to the
performance penalty introduced by this fix.
Closes https://github.com/espressif/esp-idf/issues/10403
- GCM operation in mbedtls used ECB, which calculated only 16 bytes of data each time.
- Therefore, when processing a large amount of data, it is necessary to frequently set hardware acceleration calculations,
- which could not make good use of the AES DMA function to improve efficiency.
- Hence, GCM implementation is replaced with CTR-based calculation which utilizes AES DMA to improve efficiency.
This fix adds a workaround to disable compiler optimization flag "-ftree-loop-distribute-patterns"
for `mpi_to_mem_block` routine. It was observed that compiler with release configuration was falling
back to `memset` call from ROM library causing an issue in correctly zero initializing MPI peripheral
block.
Please see following linked issue for more discussion and context on this issue.
Closes https://github.com/espressif/esp-idf/issues/8710
Closes https://github.com/espressif/esp-idf/issues/9371
Closes https://github.com/espressif/esp-idf/issues/9256
Closes IDFGH-7102
Closes IDFGH-7842
Closes IDFGH-7714
Closes IDFCI-1452
Closes IDF-6029
- While checking if ciphersuite uses RSA key exchange methods,
the APIs `mbedtls_ssl_get_ciphersuite_id_from_ssl` and
`mbedtls_ssl_ciphersuite_from_id` were used to get the ciphersuite
info.
- However, this is incorrect as we need the ciphersuite info from the
handshake instance and not the ssl_session instance.
This function removes the following legacy atomic CAS functions:
From compare_set.h (file removed):
- compare_and_set_native()
- compare_and_set_extram()
From portmacro.h
- uxPortCompareSet()
- uxPortCompareSetExtram()
Users should call esp_cpu_compare_and_set() instead as this function hides the details
of atomic CAS on internal and external RAM addresses.
Due to the removal of compare_set.h, some missing header includes are also fixed in this commit.
