* Some components have initialization dependencies. To account for
them, simple numeric priority values are introduced.
* esp_system_init_fn_array moved into Flash from DRAM
* System init functions defined using ESP_SYSTEM_INIT_FN now return
an error code. This enables simpler and more consistent error
handling in the init functions. Returning an error from an init
function is now a valid approach — the startup code will print
an error and abort.
1. Since the baud rate in the ROM cannot be changed,
set the default baud rate of the 26Mhz version
of esp32c2 to 74800
2. Since the systimer configuration of the 26Mhz
version requires a non-integer systimer frequency
configuration, and this feature is not supported
in the current ROM, this option is disabled for
the 26Mhz version esp32c2
1. Rename MACROs SYSTEM_WIFI_RST_EN register bit fields to be more recognizable
2. reset Bluetooth baseband and clock bits to fix the issue of task watchdog triggered during controller initialization due to invalid hardware state
Adding prop and lit sections to the ELF will let the debugger and the disassembler
have more info about data bytes present in the middle of the Xtensa
instructions, usually used for padding.
The change fixes thread-local-storage size by removing .srodata section
from it. It initially was included in TLS section by mistake.
The issue was found when stack size increased after building applications
with GCC-11.1 compiler. Stack size became bigger because some new data
appeared in .srodata. See more details here:
adce62f53d
SMP FreeRTOS uses a single kernel lock for all critical sections. There is a known
issue with esp_ipc_isr_stall_other_cpu() that can cause dead if the other CPU is
already in a critical section.
This commit adds a temporary workaround to reduce the chance of deadlock by taking
the SMP FreeRTOS kernel lock first before stalling the other CPU.
See IDF-5257 for more details.
The previously used splits between memory allocated for ROM code,
2nd stage bootloader and the app were somewhat safe and conservative.
This resulted in some space being unavailable for static allocation
in the app.
This commit increases the space available for static allocation to the
maximum possible amount.
1. Some of the ROM code static allocation is only used in UART/USB/SPI
download modes. This region ("shared buffers") has been placed at
the lower end of ROM memory area, to be reusable in flash boot
mode. The 2nd stage bootloader linker script is modified to "pack"
all sections exactly up to the end but with roughly 8K margin between
startup stacks.
2. Instead of calculating the sections placement and hardcoding the
addresses in the LD script again, rewrite it to calculate the
start address of each memory region automatically based on the
logic above.
3. Adjust the app memory layout (SRAM_IRAM_END) accordingly,
increasing the space available for static allocation.
Overall these changes increase the space available for static
allocation by about 78kB.
The downside of these changes is that the 2nd stage bootloader .data
segment is now directly adjacent to the startup stack on the PRO CPU.
Previously, there was effectively about 78kB of extra stack space for
the PRO CPU, before the stack would run into the data segment.
This commit makes changes to cpu_ll.h, cpu_hal.h, and interrupt_controller_hal.h:
- Moved to esp_hw_support in order to be deprecated in the future
- HAL/LL API now route their calls to esp_cpu.h functions instead
Also updated soc_hal.h as follows:
- Removed __SOC_HAL_..._OTHER_CORES() macros as they dependend on cpu_hal.h
- Made soc_hal.h and soc_ll.h interfaces always inline, and removed soc_hal.c.
This commit also updates the XCHAL_ERRATUM_572 workaround by
- Removing it's HAL function and invoking the workaround it directly the bootloader
- Added missing workaround for the ESP32-S3
Was: Backtrace: N:M N:M N:M ...
Now: Backtrace:N:MN:M N:M ...
The problem with the new format is that it is hard to parse and
breaks the parser that is used by PlatformIO. The old format
is much more reasonable. I do not see how the pattern in IDFDUT.py
can work with the new format, due to the missing space after the :
