esp-idf/components/esptool_py/Kconfig.projbuild

217 lines
7.9 KiB
Plaintext
Raw Normal View History

2016-08-17 11:08:22 -04:00
menu "Serial flasher config"
config ESPTOOLPY_NO_STUB
bool "Disable download stub"
2021-10-18 05:02:19 -04:00
default "y" if IDF_TARGET_ESP32H2 && IDF_ENV_FPGA # TODO: IDF-4288
default "n"
2021-09-02 08:48:39 -04:00
help
The flasher tool sends a precompiled download stub first by default. That stub allows things
like compressed downloads and more. Usually you should not need to disable that feature
config ESPTOOLPY_OCT_FLASH
depends on IDF_TARGET_ESP32S3
bool "Enable Octal Flash"
default n
choice ESPTOOLPY_FLASHMODE
prompt "Flash SPI mode"
default ESPTOOLPY_FLASHMODE_DIO
default ESPTOOLPY_FLASHMODE_OPI if ESPTOOLPY_OCT_FLASH
help
Mode the flash chip is flashed in, as well as the default mode for the
binary to run in.
config ESPTOOLPY_FLASHMODE_QIO
depends on !ESPTOOLPY_OCT_FLASH
bool "QIO"
config ESPTOOLPY_FLASHMODE_QOUT
depends on !ESPTOOLPY_OCT_FLASH
bool "QOUT"
config ESPTOOLPY_FLASHMODE_DIO
depends on !ESPTOOLPY_OCT_FLASH
bool "DIO"
config ESPTOOLPY_FLASHMODE_DOUT
depends on !ESPTOOLPY_OCT_FLASH
bool "DOUT"
config ESPTOOLPY_FLASHMODE_OPI
depends on ESPTOOLPY_OCT_FLASH
bool "OPI"
endchoice
choice ESPTOOLPY_FLASH_SAMPLE_MODE
prompt "Flash Sampling Mode"
default ESPTOOLPY_FLASH_SAMPLE_MODE_DTR if ESPTOOLPY_OCT_FLASH
default ESPTOOLPY_FLASH_SAMPLE_MODE_STR if !ESPTOOLPY_OCT_FLASH
config ESPTOOLPY_FLASH_SAMPLE_MODE_STR
bool "STR Mode"
config ESPTOOLPY_FLASH_SAMPLE_MODE_DTR
depends on ESPTOOLPY_OCT_FLASH
bool "DTR Mode"
endchoice
# Note: we use esptool.py to flash bootloader in
# dio mode for QIO/QOUT, bootloader then upgrades
# itself to quad mode during initialisation
config ESPTOOLPY_FLASHMODE
string
default "dio" if ESPTOOLPY_FLASHMODE_QIO
default "dio" if ESPTOOLPY_FLASHMODE_QOUT
default "dio" if ESPTOOLPY_FLASHMODE_DIO
default "dout" if ESPTOOLPY_FLASHMODE_DOUT
# The 1st and 2nd bootloader doesn't support opi mode,
# using fastrd instead. For now the ESPTOOL doesn't support
# fasted (see ESPTOOL-274), using dout instead. In ROM the flash mode
# information get from efuse, so don't care this dout choice.
default "dout" if ESPTOOLPY_FLASHMODE_OPI
choice ESPTOOLPY_FLASHFREQ
prompt "Flash SPI speed"
default ESPTOOLPY_FLASHFREQ_40M if IDF_TARGET_ESP32
default ESPTOOLPY_FLASHFREQ_80M if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3 || IDF_TARGET_ESP32C3
default ESPTOOLPY_FLASHFREQ_60M if IDF_TARGET_ESP32C2
default ESPTOOLPY_FLASHFREQ_48M if IDF_TARGET_ESP32H2
config ESPTOOLPY_FLASHFREQ_120M
bool "120 MHz"
depends on SOC_MEMSPI_SRC_FREQ_120M && ESPTOOLPY_FLASH_SAMPLE_MODE_STR
config ESPTOOLPY_FLASHFREQ_80M
bool "80 MHz"
depends on SOC_MEMSPI_SRC_FREQ_80M_SUPPORTED
config ESPTOOLPY_FLASHFREQ_60M
bool "60 MHz"
depends on SOC_MEMSPI_SRC_FREQ_60M_SUPPORTED
config ESPTOOLPY_FLASHFREQ_48M
bool "48 MHz"
depends on SOC_MEMSPI_SRC_FREQ_48M_SUPPORTED
config ESPTOOLPY_FLASHFREQ_40M
bool "40 MHz"
depends on SOC_MEMSPI_SRC_FREQ_40M_SUPPORTED
config ESPTOOLPY_FLASHFREQ_30M
bool "30 MHz"
depends on SOC_MEMSPI_SRC_FREQ_30M_SUPPORTED
config ESPTOOLPY_FLASHFREQ_26M
bool "26 MHz"
depends on SOC_MEMSPI_SRC_FREQ_26M_SUPPORTED
config ESPTOOLPY_FLASHFREQ_24M
bool "24 MHz"
depends on SOC_MEMSPI_SRC_FREQ_24M_SUPPORTED
config ESPTOOLPY_FLASHFREQ_20M
bool "20 MHz"
depends on SOC_MEMSPI_SRC_FREQ_20M_SUPPORTED
config ESPTOOLPY_FLASHFREQ_15M
bool "15 MHz"
depends on SOC_MEMSPI_SRC_FREQ_15M_SUPPORTED
endchoice
config ESPTOOLPY_FLASHFREQ
string
# On some of the ESP chips, max boot frequency would be equal to (or even lower than) 80m.
# We currently define this to `80m`.
default '80m' if ESPTOOLPY_FLASHFREQ_120M
default '80m' if ESPTOOLPY_FLASHFREQ_80M
default '60m' if ESPTOOLPY_FLASHFREQ_60M
default '48m' if ESPTOOLPY_FLASHFREQ_48M
default '30m' if ESPTOOLPY_FLASHFREQ_30M
default '24m' if ESPTOOLPY_FLASHFREQ_24M
default '40m' if ESPTOOLPY_FLASHFREQ_40M
default '26m' if ESPTOOLPY_FLASHFREQ_26M
default '20m' if ESPTOOLPY_FLASHFREQ_20M
default '20m' # if no clock can match in bin headers, go with minimal.
choice ESPTOOLPY_FLASHSIZE
prompt "Flash size"
default ESPTOOLPY_FLASHSIZE_2MB
help
SPI flash size, in megabytes
config ESPTOOLPY_FLASHSIZE_1MB
bool "1 MB"
config ESPTOOLPY_FLASHSIZE_2MB
bool "2 MB"
config ESPTOOLPY_FLASHSIZE_4MB
bool "4 MB"
config ESPTOOLPY_FLASHSIZE_8MB
bool "8 MB"
config ESPTOOLPY_FLASHSIZE_16MB
bool "16 MB"
config ESPTOOLPY_FLASHSIZE_32MB
bool "32 MB"
config ESPTOOLPY_FLASHSIZE_64MB
bool "64 MB"
config ESPTOOLPY_FLASHSIZE_128MB
bool "128 MB"
endchoice
config ESPTOOLPY_FLASHSIZE
string
default "1MB" if ESPTOOLPY_FLASHSIZE_1MB
default "2MB" if ESPTOOLPY_FLASHSIZE_2MB
default "4MB" if ESPTOOLPY_FLASHSIZE_4MB
default "8MB" if ESPTOOLPY_FLASHSIZE_8MB
default "16MB" if ESPTOOLPY_FLASHSIZE_16MB
default "32MB" if ESPTOOLPY_FLASHSIZE_32MB
default "64MB" if ESPTOOLPY_FLASHSIZE_64MB
default "128MB" if ESPTOOLPY_FLASHSIZE_128MB
config ESPTOOLPY_HEADER_FLASHSIZE_UPDATE
bool "Detect flash size when flashing bootloader"
default n
help
If this option is set, flashing the project will automatically detect
the flash size of the target chip and update the bootloader image
before it is flashed.
Enabling this option turns off the image protection against corruption
by a SHA256 digest. Updating the bootloader image before flashing would
invalidate the digest.
choice ESPTOOLPY_BEFORE
prompt "Before flashing"
default ESPTOOLPY_BEFORE_RESET
help
Configure whether esptool.py should reset the ESP32 before flashing.
Automatic resetting depends on the RTS & DTR signals being
wired from the serial port to the ESP32. Most USB development
boards do this internally.
config ESPTOOLPY_BEFORE_RESET
bool "Reset to bootloader"
config ESPTOOLPY_BEFORE_NORESET
bool "No reset"
endchoice
config ESPTOOLPY_BEFORE
string
default "default_reset" if ESPTOOLPY_BEFORE_RESET
default "no_reset" if ESPTOOLPY_BEFORE_NORESET
choice ESPTOOLPY_AFTER
prompt "After flashing"
default ESPTOOLPY_AFTER_RESET
help
Configure whether esptool.py should reset the ESP32 after flashing.
Automatic resetting depends on the RTS & DTR signals being
wired from the serial port to the ESP32. Most USB development
boards do this internally.
config ESPTOOLPY_AFTER_RESET
bool "Reset after flashing"
config ESPTOOLPY_AFTER_NORESET
bool "Stay in bootloader"
endchoice
config ESPTOOLPY_AFTER
string
default "hard_reset" if ESPTOOLPY_AFTER_RESET
default "no_reset" if ESPTOOLPY_AFTER_NORESET
config ESPTOOLPY_MONITOR_BAUD
int
default ESP_CONSOLE_UART_BAUDRATE if ESP_CONSOLE_UART
default 115200 if !ESP_CONSOLE_UART
2016-08-17 11:08:22 -04:00
endmenu