1. Fix the bug that Wi-Fi performance is impacted by BLE starting scan for a while in some scenarios on ESP32-C3.
2. Fix the bug that Wi-Fi performance is impacted when Bluetooth change state for a while in some scenarios on ESP32-C3.
3. Fix the bug that BLE performance is impacted by Wi-Fi scan on ESP32-C3.
4. Fix the bug that Wi-Fi scan fails when BLE is scanning on ESP32-C3.
5. Fix Wi-Fi ACK and CTS rate when low rate is disabled on ESP32-C3.
components/bt: Do not use feature: timer support isr dispatch method
disable controller after wake up finished.
protect critical section of power down
choose clk in sleep
components/coex: mac bb power down in light sleep
components/coex: Macro changed
components/os: protect reserved interrupt number
update phy to phy_version 300,6e46ba7,Jan 25 2021
some bugfix
This adds support for the retargetable locking implementation in
newlib 3. This feature will be enabled in the future toolchain builds.
With the present version of the toolchain, this code doesn't get used.
When _RETARGETABLE_LOCKING gets enabled, newlib locking implementation
will be modified as follows:
- Legacy ESP-specific _lock_xxx functions are preserved. This is done
because ROM copies of newlib in ESP32 and ESP32-S2 rely on these
functions through the function pointer table. Also there is some
code in IDF which still uses these locking functions.
- New __retarget_lock_xxx functions are introduced. Newlib expects
these functions to be provided by the system. These functions work
pretty much the same way as the ESP-specific _lock_xxx functions,
except one major difference: _lock_acquire receives the lock pointer
by value, and as such doesn't support lazy initialization.
- Static locks used by newlib are now explicitly initialized at
startup. Since it is unlikely that these static locks are used at
the same time, all compatible locks are set to point to the same
mutex. This saves a bit of RAM. Note that there are still many locks
not initialized statically, in particular those inside FILE
structures.
During HAL layer refactoring and new chip bringup, we have several
caps.h for each part, to reduce the conflicts to minimum. But this is
The capabilities headers will be relataive stable once completely
written (maybe after the featues are supported by drivers).
Now ESP32 and ESP32-S2 drivers are relative stable, making it a good
time to combine all these caps.h into one soc_caps.h
This cleanup also move HAL config and pin config into separated files,
to make the responsibilities of these headers more clear. This is
helpful for the stabilities of soc_caps.h because we want to make it
public some day.
The remaining 4 kB had been reserved for storing RF calibration and
BT stack state since 4e092be6. However, these features never got
implemented. If we ever need to place RF related data into RTC slow
memory, we can do this by creating a variable with RTC_NOINIT_ATTR
instead.
Closes https://github.com/espressif/esp-idf/issues/3993
1. The 2nd bootloader always call `rom_spiflash_unlock()`, but never help to clear the WEL bit when exit. This may cause system unstability.
This commit helps to clear WEL when flash configuration is done.
**RISK:** When the app starts, it didn't have to clear the WEL before it actually write/erase. But now the very first write/erase operation should be done after a WEL clear. Though the risk is little (all the following write/erase also need to clear the WEL), we still have to test this carefully, especially for those functions used by the OTA.
2. The `rom_spiflash_unlock()` function in the patch of ESP32 may (1) trigger the QPI, (2) clear the QE or (3) fail to unlock the ISSI chips.
Status register bitmap of ISSI chip and GD chip:
| SR | ISSI | GD25LQ32C |
| -- | ---- | --------- |
| 0 | WIP | WIP |
| 1 | WEL | WEL |
| 2 | BP0 | BP0 |
| 3 | BP1 | BP1 |
| 4 | BP2 | BP2 |
| 5 | BP3 | BP3 |
| 6 | QE | BP4 |
| 7 | SRWD | SRP0 |
| 8 | | SRP1 |
| 9 | | QE |
| 10 | | SUS2 |
| 11 | | LB1 |
| 12 | | LB2 |
| 13 | | LB3 |
| 14 | | CMP |
| 15 | | SUS1 |
QE bit of other chips are at the bit 9 of the status register (i.e. bit 1 of SR2), which should be read by RDSR2 command.
However, the RDSR2 (35H, Read Status 2) command for chip of other vendors happens to be the QIOEN (Enter QPI mode) command of ISSI chips. When the `rom_spiflash_unlock()` function trys to read SR2, it may trigger the QPI of ISSI chips.
Moreover, when `rom_spiflash_unlock()` try to clear the BP4 bit in the status register, QE (bit 6) of ISSI chip may be cleared by accident. Or if the ISSI chip doesn't accept WRSR command with argument of two bytes (since it only have status register of one byte), it may fail to clear the other protect bits (BP0~BP3) as expected.
This commit makes the `rom_spiflash_unlock()` check whether the vendor is issi. if so, `rom_spiflash_unlock()` only send RDSR to read the status register, send WRSR with only 1 byte argument, and also avoid clearing the QE bit (bit 6).
3. `rom_spiflash_unlock()` always send WRSR command to clear protection bits even when there is no protection bit active. And the execution of clearing status registers, which takes about 700us, will also happen even when there's no bits cleared.
This commit skips the clearing of status register if there is no protection bits active.
Also move the execute_flash_command to be a bootloader API; move
implementation of spi_flash_wrap_set to the bootloader
* changing dependencies from unity->cmock
* added component.mk and Makefile.projbuild
* ignore test dir in gen_esp_err_to_name.py
* added some brief introduction of CMock in IDF
Goal is that multiple faults would be required to bypass a boot-time signature check.
- Also strengthens some address range checks for safe app memory addresses
- Change pre-enable logic to also check the bootloader signature before enabling SBV2 on ESP32
Add some additional checks for invalid sections:
- Sections only partially in DRAM or IRAM are invalid
- If a section is in D/IRAM, allow the possibility only some is in D/IRAM
- Only pass sections that are entirely in the same type of RTC memory region
1. use spi functions in rom
2. remove unnecessary GPIO configurations.
3. remove unnecessary dummy settings.
4. enable dummy out function
5. flash and psram have independent timing setting registers.
6. no need to set 1.9v for LDO in 80Mhz
7. set IO driver ability to 1 by default.
8. no need to use GPIO matrix on esp32s2, IO MUX is recommended
9. enable spi clock mode and IO mode settings
