Functions used for burning this efuse would log, but at this point
esp_log is not initialized. Moved to a later point in the startup process.
Closes https://github.com/espressif/esp-idf/issues/9457
ESP32-S3 stacks have currently have less useable space compared to other targets (due to
AI coprocessor context registers). This has caused a stack overflow in the IPC tasks under
some configurations. This commit increases the default IPC stack size for the ESP32-S3.
Blocking read from cdcacm VFS could return less bytes than requested.
This didn’t match the behaviour of other VFS drivers, and higher level
code could misbehave.
Previously, reset over USB CDC was done by calling esp_restart from
an interrupt handler. This works only until some restart hook function
is registered using esp_register_shutdown_handler, and the hook
function tries to do something that isn’t allowed in an interrupt
handler. One such case is with Wi-Fi. When Wi-Fi driver is installed,
it registers esp_wifi_stop as a shutdown handler function. However
esp_wifi_stop cannot be called from an ISR, and hence we shouldn’t
call esp_restart from an ISR either.
This commit modifies USB CDC driver to call esp_restart by posting it
to esp_timer task.
Closes https://github.com/espressif/esp-idf/issues/7404
Spinlocks themselves do not constitute critical sections as after a spinlock is acquired, interrupts
can remain enabled. However, there are some places where spinlocks are used direclty instead of using
the portMUX_TYPE and portENTER_CRITICAL_...() APIs. This commit fixes those calls.
- Remove esp_cpu_in_ocd_mode() from esp_cpu.h. Users should call esp_cpu_dbgr_is_attached() instead.
- Remove esp_cpu_get_ccount() from esp_cpu.h. Users should call esp_cpu_get_cycle_count() instead.
- Remove esp_cpu_set_ccount() from esp_cpu.h. Users should call esp_cpu_set_cycle_count() instead.
- Other IDF components updated to call esp_cpu_dbgr_is_attached(), esp_cpu_get_cycle_count() and esp_cpu_set_cycle_count() as well.
This commit marks all functions in interrupt_controller_hal.h, cpu_ll.h and cpu_hal.h as deprecated.
Users should use functions from esp_cpu.h instead.
The following two functions in bootloader_support are private now:
* esp_secure_boot_verify_sbv2_signature_block()
* esp_secure_boot_verify_rsa_signature_block()
They have been moved into private header files
inside bootloader_private/
* Removed bootloader_reset_reason.h and
bootloader_common_get_reset_reason() completely.
Alternative in ROM component is available.
* made esp_efuse.h independent of target-specific rom header
* Some components have initialization dependencies. To account for
them, simple numeric priority values are introduced.
* esp_system_init_fn_array moved into Flash from DRAM
* System init functions defined using ESP_SYSTEM_INIT_FN now return
an error code. This enables simpler and more consistent error
handling in the init functions. Returning an error from an init
function is now a valid approach — the startup code will print
an error and abort.
1. Since the baud rate in the ROM cannot be changed,
set the default baud rate of the 26Mhz version
of esp32c2 to 74800
2. Since the systimer configuration of the 26Mhz
version requires a non-integer systimer frequency
configuration, and this feature is not supported
in the current ROM, this option is disabled for
the 26Mhz version esp32c2
1. Rename MACROs SYSTEM_WIFI_RST_EN register bit fields to be more recognizable
2. reset Bluetooth baseband and clock bits to fix the issue of task watchdog triggered during controller initialization due to invalid hardware state
Adding prop and lit sections to the ELF will let the debugger and the disassembler
have more info about data bytes present in the middle of the Xtensa
instructions, usually used for padding.
The change fixes thread-local-storage size by removing .srodata section
from it. It initially was included in TLS section by mistake.
The issue was found when stack size increased after building applications
with GCC-11.1 compiler. Stack size became bigger because some new data
appeared in .srodata. See more details here:
adce62f53d
