Commit Graph

223 Commits

Author SHA1 Message Date
Konstantin Kondrashov
a8e46775c6 soc/rtc_wdt: Add API functions for rtc_wdt
Added functions:
rtc_wdt_protect_off/on
rtc_wdt_set_length_of_reset_signal
rtc_wdt_set_stage
rtc_wdt_set_time
rtc_wdt_feed
rtc_wdt_disable/enable
2018-08-14 17:48:02 +05:00
Tian Hao
ee787085f9 component/bt : decrease memory consumption by conn number
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
2018-08-14 02:29:17 +00:00
Ivan Grokhotkov
8739111218 Merge branch 'bugfix/gpio_reset_bitmask' into 'master'
gpio: Bitmask overflow fix in gpio_reset_pin

See merge request idf/esp-idf!2966
2018-08-10 17:35:26 +08:00
Taavi Hein
f7749e18a8 gpio: Bitmask overflow fix in gpio_reset_pin
For pins 32 and up the BIT(nr) macro used here overflowed,
causing undetermined GPIO pins to be reset.
Example: freeing SPI device/bus where CS is on pin 33
caused debug UART to cease communication, TXD0 was
disabled.

Fixed as BIT64(nr) macro, to be used elsewhere as needed.
For example in definitions like GPIO_SEL_32..GPIO_SEL_39.
2018-08-08 15:31:17 +03:00
Angus Gratton
a5ae5ac4b3 soc: Allow components to reserve fixed memory ranges that they need
No longer necessary to keep all reserved addresses in 'soc'.

Means 'soc' does not need to know about 'bt', for example.

Also means that Bluetooth can be enabled in config without any memory being reserved for BT
controller. Only if code calling the BT controller is linked in, will this memory be reserved...
2018-08-06 01:37:55 +00:00
David Cermak
409c91bcb9 removed possible uint16 access to 32bit register, noted fifo use not recommended 2018-07-23 07:57:18 +02:00
Ivan Grokhotkov
fec079cd44 Merge branch 'bugfix/rtc_io_hold_regs' into 'master'
Fix errors in rtc_gpio_desc values

See merge request idf/esp-idf!2765
2018-07-19 15:04:42 +08:00
Ivan Grokhotkov
5376a06d7b Merge branch 'bugfix/range_CONFIG_ESP32_RTC_CLK_CAL_CYCLES' into 'master'
soc/clk: Fix range CONFIG_ESP32_RTC_CLK_CAL_CYCLES

See merge request idf/esp-idf!2719
2018-07-17 19:43:11 +08:00
negativekelvin
8a9e3875ed
Fix errors in rtc_gpio_desc values 2018-07-12 23:16:15 -07:00
Angus Gratton
a67d5d89e0 Replace all DOS line endings with Unix
Command run was:
git ls-tree -r HEAD --name-only | xargs dos2unix
2018-07-12 19:10:37 +08:00
Konstantin Kondrashov
ac3508615a soc/clk: Fix range CONFIG_ESP32_RTC_CLK_CAL_CYCLES
Fixed the error division on zero.
Also fixed range CONFIG_ESP32_RTC_CLK_CAL_CYCLES in Kconfig.
Fixed a overflow error by TIMG in the function rtc_clk_cal_internal. This error was due to a limit in values TIMG_RTC_CALI_MAX=0x7FFF (to write the slowclk_cycles) and TIMG_RTC_CALI_VALUE=0x1FFFFFF (to read xtal_cycles). Added assert finctions.

Closes https://github.com/espressif/esp-idf/issues/2147
2018-07-10 11:56:12 +05:00
Darian Leung
1d2727f4c8 CAN Driver
The following commit contains the first version of the ESP32 CAN Driver.

closes #544
2018-07-04 14:01:57 +08:00
Konstantin Kondrashov
32da455384 soc: Fix check_long_hold_gpio and move def to soc
Fix factory_reset_pin init as input
Move definition a structure rtc_gpio_desc to soc

Closes https://github.com/espressif/esp-idf/issues/2030
2018-06-22 09:20:27 +05:00
Ivan Grokhotkov
4b91c82cc4 Merge branch 'feat/sdio_pullup' into 'master'
feature(sdio): add features to make SDIO slave compatible with more devkits

See merge request idf/esp-idf!2454
2018-06-20 13:58:56 +08:00
michael
5b37a96ddc feature(sdio): allow to enable internal pullups of the SDIO host and slave as a debug feature
NOTE: the internal pullups are not totally reliable, please do add external pullups on your bus.
2018-06-14 12:04:22 +08:00
Michael (XIAO Xufeng)
ebfda40b7c refactor(spi): move pin information into soc folder 2018-06-14 11:29:15 +08:00
Michael (XIAO Xufeng)
939e5693a5 chore(spi): fix the terms of native to iomux 2018-06-06 06:08:39 +00:00
michael
5cf7d3768d feat(spi_master): fine tune the timing of SPI 2018-06-06 06:08:39 +00:00
Angus Gratton
6b9784cc45 Merge branch 'master' into feature/cmake_update 2018-05-31 14:46:23 +10:00
Angus Gratton
3e1a93e5a7 soc: rtc_vddsdio_get_config() In default configuration, VDD_SDIO LDO is always enabled
When using bootstrapping pin to enable VDD_SDIO, the internal LDO is always enabled at either 1.8V
or 3.3V.
2018-05-25 15:14:13 +10:00
Angus Gratton
d775cc4c4c soc: Fix description of rtc_config_t.tieh, add macros
Usage of TIEH was correct but description had 1.8V & 3.3V backwards.

Add macro definitions for TIEH values to improve readability.
2018-05-25 14:58:37 +10:00
Angus Gratton
b8312a26c0 Merge branch 'feature/sdio_slave' into 'master'
feature(sdio_slave): add support for sdio_slave

See merge request idf/esp-idf!1829
2018-05-22 09:43:35 +08:00
Konstantin Kondrashov
e5b280f173 dport: Bigfix dport_read code move to IRAM
A new method of workaround an error with DPORT is to ensure that the APB is read and followed by the DPORT register without interruptions and pauses. This fix places this implementation in the IRAM to exclude errors associated with the cache miss.
2018-05-21 22:00:51 +05:00
Michael (XIAO Xufeng)
c73575de4f feat(sdio_slave): add headers for sdio slave components: slc, host, hinf 2018-05-21 23:48:33 +08:00
wangmengyang
22e21b38f7 component/bt: implement bluetooth modem sleep mode, one mode for BLE only and another for dual mode bluetooth
1. provide options for bluetooth low power mode
2. provide two options for bluetooth low power clock: main XTAL and external 32kHz XTAL
3. provide function and callbacks to control bluetooth low power mode, including enable/disable sleep, software wakeup request, low power clock settings, check power state, etc
4. modify vhci API vhci_host_send_packet to use blocking mode
5. note that DFS and bluetooth modem sleep can not be used together currently.
2018-05-19 15:37:26 +08:00
Angus Gratton
7ae1e9463e Merge branch 'bugfix/rtc_xtal_tests' into 'master'
ci: Only run XTAL unit tests assuming board has an XTAL

See merge request idf/esp-idf!2401
2018-05-15 18:44:46 +08:00
Angus Gratton
05e09a5bac ci: Only run XTAL unit tests assuming board has an XTAL, run less repeats 2018-05-15 15:43:24 +08:00
Angus Gratton
d1066e9d7f Merge branch 'feature/dport_access' into 'master'
soc: Dport access with pre-read register APB

See merge request idf/esp-idf!2257
2018-05-15 15:32:28 +08:00
Angus Gratton
662fe55996 Merge branch 'bugfix/select_rtc_slow_clk' into 'master'
esp32/clk: Fix starting rtc oscillator if it bad

See merge request idf/esp-idf!2215
2018-05-15 12:57:22 +08:00
Konstantin Kondrashov
9ad0760b9d esp32/clk:Fix starting rtc oscillator if it is bad
If the RTC crystal is bad or has no matched capacitance, then you do not need to start such the crystal. It is necessary to determine this case, output an error (about impossibility to start from the oscillator) and start from the internal RC of the chain.

Reduced the default value of the number of bootstrap cycles. Because we can oscillating the oscillator which then stops. (in Kconfig). Changed from 100 to 5.

The number of calibration cycles has been increased. It is the main criterion for estimating the launch of an oscillator. A large increase leads to an increase in the load time, as well as the stability of recognition of this case. (in Kconfig).
Changed from 1024 to 3000.
2018-05-15 08:59:15 +05:00
Konstantin Kondrashov
8f80cc733d soc: Change DPORT access
When two CPUs read the area of the DPORT and the area of the APB, the result is corrupted for the CPU that read the APB area.
And another CPU has valid data.

The method of eliminating this error.
Before reading the registers of the DPORT, make a preliminary reading of the APB register.
In this case, the joint access of the two CPUs to the registers of the APB and the DPORT is successful.
2018-05-14 17:54:57 +05:00
jack
c384fa2492 rename clock enable and reset bits for SPI modules
1.The names of clock enable and reset bits do not match with TRM, just rename them.
2018-05-14 16:45:03 +08:00
Jiang Jiang Jian
db90f49758 Merge branch 'bugfix/update_emac_h' into 'master'
update emac_reg_v2.h

See merge request idf/esp-idf!2050
2018-05-07 16:16:52 +08:00
Angus Gratton
1cb5712463 cmake: Add component dependency support
Components should set the COMPONENT_REQUIRES & COMPONENT_PRIVATE_REQUIRES variables to define their
requirements.
2018-04-30 09:59:20 +10:00
Angus Gratton
c671a0c3eb build system: Initial cmake support, work in progress 2018-04-30 09:59:20 +10:00
Ivan Grokhotkov
94250e42a0 sleep: optimize light sleep wakeup latency 2018-04-26 19:36:47 +08:00
Ivan Grokhotkov
ac623a9756 soc/rtc: restore dbg attenuation when waking from sleep
This fixes inability to enter deep sleep after waking up from light sleep
2018-04-26 18:52:46 +08:00
Ivan Grokhotkov
d38b22b11b soc/rtc, sleep: don’t lower the bias for wakeup state
This fixes watchdog resets occurring during wakeup from light sleep.
2018-04-26 18:52:45 +08:00
Ivan Grokhotkov
b0a91630fb soc/rtc: allow main XTAL to be powered on in sleep 2018-04-26 18:52:45 +08:00
Ivan Grokhotkov
3c78faa0a9 soc/rtc: don’t switch frequency in rtc_sleep_init 2018-04-26 18:52:45 +08:00
shangke
5fc130f2c0 update emac_reg_v2.h 2018-04-25 14:54:09 +08:00
Ivan Grokhotkov
52f9a5ca16 Merge branch 'bugfix/sdspi_wp_cd_pins' into 'master'
sdmmc, sdspi: fix handling of CD and WP

See merge request idf/esp-idf!2285
2018-04-24 20:53:47 +08:00
Ivan Grokhotkov
85ab4fc83e sdmmc host: add handling of CD and WP pins
Previous version of the code only connected CD and WP to the
peripheral, in fact the hardware does not use the values of these
signals automatically. This adds code to read CD and WP values when
command is executed and return errors if card is not present, or
write command is executed when WP signal is active.
2018-04-24 19:08:44 +08:00
Ivan Grokhotkov
9c7207ed3c Merge branch 'bugfix/soc_clk_out_fields' into 'master'
soc/io_mux: make CLK_OUT fields compatible with REG_SET/GET_FIELD

See merge request idf/esp-idf!2133
2018-04-13 19:42:20 +08:00
Ivan Grokhotkov
ee600784c5 sdmmc: add SDIO support
- Add SDIO support at protocol layer (probing, data transfer, interrupts)
- Add SDIO interrupts support in SDMMC host
- Add test (communicate with ESP32 in SDIO download mode)
2018-04-11 11:07:13 +08:00
Ivan Grokhotkov
2522c1b2f9 Merge branch 'bugfix/rtc_clk_fixes' into 'master'
Power management and RTC fixes

See merge request idf/esp-idf!2131
2018-04-10 18:17:02 +08:00
Angus Gratton
53234ef2bc Merge branch 'refactor/rtc_split_module' into 'master'
bugfix(rtc): make sure peripherals (DAC, HALL) are turned off before conversion.

See merge request idf/esp-idf!1848
2018-04-04 09:00:58 +08:00
Angus Gratton
da27816314 Merge branch 'feat/add_efuse_cpu_freq_rating' into 'master'
efuse/add cpu freq rating

See merge request idf/esp-idf!1994
2018-03-29 05:59:52 +08:00
Michael (Xiao Xufeng)
cef8baf424 bugfix(rtc): make sure peripherals (DAC, HALL) are turned off before conversion.
refactor structure of ``rtc_module.c`` to make it more clearly.

Closes https://github.com/espressif/esp-idf/issues/1517
2018-03-28 17:10:01 +08:00
Ivan Grokhotkov
b007b89b84 soc/io_mux: make CLK_OUT fields compatible with REG_SET/GET_FIELD 2018-03-27 12:10:18 +08:00
Ivan Grokhotkov
43b5fdd5c9 soc/rtc: fix switching between 80/160 and 240MHz
Previous code contained a check for PLL frequency to be 240MHz, while
in fact 240MHz was a CPU frequency; corresponding PLL frequency is
480MHz. Fixed the comparison and replaced integer MHz values with an
enum.
2018-03-27 10:55:59 +08:00
Ivan Grokhotkov
48d55e22e7 soc/rtc: run 32k XTAL startup test only in PSRAM config
PSRAM tests run on ESP-WROVER-KIT boards, which have the 32k XTAL
installed.
2018-03-26 10:14:13 +08:00
Ivan Grokhotkov
887b6e2925 Merge branch 'bugfix/rtc_clk_32k_bootstrap' into 'master'
bugfix/rtc_clk_32k_bootstrap: Fix starting 32k RTC

See merge request idf/esp-idf!2085
2018-03-21 18:38:49 +08:00
Konstantin Kondrashov
f7df532ec0 bugfix/rtc_clk_32k_bootstrap: Fix starting 32k RTC
1. External 32kHz crystal is started for too long or it may not start at all. It is often observed at the first start.
2. At the first start, it is possible that the crystal did not start. And the recorded period was recorded as 0. Which led to a division error by zero during the transition to the deep sleep mode (Maybe somewhere else).
3. Added a unit test to test a new method of oscillation an external crystal.
4. Added a new method of oscillating of an external crystal. The legs of the crystal are fed with a 32 kHz frequency.

The new method eliminates these errors.

Added unit test: `\esp-idf\components\soc\esp32\test\test_rtc_clk.c`: `make TEST_COMPONENTS=soc`
- 8 Test starting external RTC crystal. Will pass.

`Bootstrap cycles for external 32kHz crystal` - is specified in the file Kconfig by default 100.

QA tested a new method of oscillation the crystal on 25 boards. The supply of square waves on the crystal showed a 100% result in contrast to the previous method of launching the crystal. After the tests, the old method was deleted.

Closes TW19143
2018-03-21 13:27:56 +05:00
Ivan Grokhotkov
1618dbc9a5 soc/rtc: wait for frequency switch to complete
The fast path of CPU frequency switch function, used in DFS, was not
waiting for the frequency switch to complete when switching from XTAL
to PLL. This resulted in incorrect reads from peripherals on APB,
where two consecutive reads could return the same value. For example,
in esp_timer, read of FRC_COUNT_REG would return same value as the
preceding read of FRC_ALARM_REG, causing time to jump by the value of
FRC_ALARM_REG / apb_freq_mhz.
2018-03-20 18:27:32 +08:00
Darian Leung
8b1277c55f efuse/add cpu freq rating
This commit adds support for CPU max freqeuency rating
bits in CPU. Bootloader will now print an error if attempting
to 160MHz rated ESP32 at 240MHz.

EFUSE_CHIP_VER_RESERVE has been replaced by the
frequency rating bits. Dependancies on EFUSE_CHIP_VER_RESERVE
have been changed to use EFUSE_CHIP_VER_PKG
2018-03-07 12:16:51 +08:00
Darian Leung
0c9e2c0fba esp_adc_cal/Remove lookup table
This commit removes the lookup table mode due to inferior performance when compared
to linear mode under attenuation 0, 1 and 2. However small portions of the lookup table
are kept for the higher voltages of atten 3 (above ADC reading 2880). That voltage range
in atten 3 has non linear characteristics making the LUT performan better than linear mode.
2018-02-22 20:01:41 +08:00
Darian Leung
73cdfbfe79 esp_adc_cal/Add eFuse functionality
This commit updates the esp_adc_cal ocmponent to support new calibration methods
which utilize calibratoin values stored in eFuse. This commit includes LUT mode
2018-02-13 21:22:48 +08:00
Ivan Grokhotkov
e381c6adde Merge branch 'bugfix/fix_i2s_adc_mode' into 'master'
driver(i2s): fix broken i2s adc mode

See merge request idf/esp-idf!1653
2018-02-11 12:58:58 +08:00
Wangjialin
451f69cc2e driver(i2s): fix broken i2s adc mode
1. Move i2s reset code from i2s_stop to i2s_start.
2. add RTC API to set sw mode for ADC
3. add description for adc_power_always_on()
4. add lock for i2s dma and RTC ADC functions.
5. add ADC read task in example

reported from bbs:  https://esp32.com/viewtopic.php?f=13&t=3490&p=17522#p17522
reported from github: https://github.com/espressif/esp-idf/issues/1333
2018-02-07 17:17:20 +08:00
Jeroen Domburg
70ab924dbb Especially when internal memory fills up, some FreeRTOS structures (queues etc) get allocated in psram. These structures also contain a spinlock, which needs an atomic-compare-swap operation to work. The psram hardware, however, does not support this operation. As a workaround, this patch detects these spinlocks and will, instead of S32C1I, use equivalent C-code to simulate the behaviour, with an (internal) mux for atomicity. 2018-02-02 17:11:06 +08:00
Angus Gratton
4297c337f9 esp32: Add IO_MUX_GPIOxx register names to match iomux names used in TRM
The TRM describes IOMUX registers are IO_MUX_x_REG for x in GPIO0-39.

Until now ESP-IDF describes them as PERIPHS_IO_MUX_(pinname)_U

This commit adds additional IOMUX register names which match the ones used in the TRM.
2018-01-30 17:09:37 +08:00
Ivan Grokhotkov
ffaf145056 Merge branch 'bugfix/xtal_freq_estimation' into 'master'
soc/rtc_clk: fix loss of precision in estimation of XTAL frequency

See merge request !1763
2018-01-23 15:37:47 +08:00
kooho
492db0591d Fix uart fifo overflow bug 2018-01-12 14:42:54 +08:00
Ivan Grokhotkov
914ab07567 Merge branch 'feature/ulp_i2c_reg' into 'master'
soc,ulp: add register definitions of RTC_I2C peripheral

See merge request !1762
2018-01-11 12:08:25 +08:00
Deng Xin
337f790fd3 bug fix of assert happen in PSRAM 2018-01-09 20:01:06 +08:00
Ivan Grokhotkov
7c584e80b0 soc/rtc_clk: fix loss of precision in estimation of XTAL frequency
RTC_FAST_CLK_FREQ_APPROX is defined as 8500000, so 0.5MHz part was lost
when dividing by MHZ. Since cal_val is 64-bit the parens can be removed.

With 40MHz XTAL for a nominal ESP32 chip, this fixes estimated XTAL
frequency from 38 to 40MHz.
2018-01-08 23:31:21 +08:00
Ivan Grokhotkov
dba291416f soc,ulp: add register definitions of RTC_I2C peripheral 2018-01-08 21:28:14 +08:00
Angus Gratton
c69af42b96 esp32: Fix backwards compatibility for pre-v2.1 bootloaders
Older bootloaders don't set RTC_XTAL_FREQ_REG or call rtc_clk_init(),
app needs to pick this up.

Reported at
https://esp32.com/viewtopic.php?f=2&t=3939&p=17836
2017-12-18 13:45:57 +11:00
Ivan Grokhotkov
a99483a727 docs: add information about execution time of ULP instructions 2017-12-11 14:05:41 +08:00
Ivan Grokhotkov
ca751648fa ulp: document the need to wait for RTC to be ready for wakeup 2017-12-11 12:11:46 +08:00
krzychb
421592a8eb LEDC Driver: Added back original definitions of 'duty_resolution' and 'clock_divider'. This update is to provide backward compatibility with ESP-IDF 2.1. 2017-12-04 21:12:56 +01:00
Jiang Jiang Jian
c672fc54fd Merge branch 'feature/ledc_more_meaningful_parameter_names' into 'master'
Provided more meaningful parameter names by renaming 'bit_num' to 'duty_resoluti…

See merge request !1440
2017-12-01 19:33:53 +08:00
Vitor Massaru Iha
cf768380b1 soc: Remove redefinition of MCU_SEL_M
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>

Merges #1290
2017-11-22 11:01:42 +08:00
Ivan Grokhotkov
3369f15fa3 soc/rtc: don't power down BIAS_I2C along with APLL if other PLL is used
If enable == false, and SOC_CLK_SEL == PLL, the code would would
erroneously set RTC_CNTL_BIAS_I2C_FORCE_PD. This change fixes the logic.
2017-11-20 15:27:16 +08:00
krzychb
d488bb7bac Provided more meaningful parameter names by renaming 'bit_num' to 'duty_resolution' and 'div_num' to 'clock_divider' 2017-11-15 08:08:12 +01:00
Ivan Grokhotkov
f22c681c1c soc/rtc: raise core voltage when 80MHz flash frequency is used
To achieve reliable operation with GD flash at 80MHz, need to raise
core voltage.
This causes the following current consumption increase:

At 80MHz: from 29mA to 33mA
At 160MHz: from 41mA to 47mA

Test conditions: 2 cores running code from IRAM, remaining peripherals
clock gated.
2017-11-08 21:13:02 +08:00
Jiang Jiang Jian
abacf8d2a0 Merge branch 'bugfix/rtc_and_restart_fixes' into 'master'
rtc_clk and esp_restart fixes

See merge request !1458
2017-11-04 01:34:38 +08:00
Ivan Grokhotkov
a02b30ccda efuse: add package definitions for PICOD2/D4 2017-11-03 15:49:10 +08:00
Ivan Grokhotkov
fb9c106bcb soc/rtc: add function to get/set VDDSDIO configuration
Also consider case of VDDSDIO force powered on in rtc_sleep.
2017-11-03 15:49:09 +08:00
Ivan Grokhotkov
5a294c9acd soc/gpio: fix description of GPIO_STRAP_REG 2017-11-03 15:49:09 +08:00
Ivan Grokhotkov
80eb3b6ddb Merge branch 'bugfix/light_sleep_current' into 'master'
soc/rtc: fix increased current consumption in light sleep

See merge request !1483
2017-11-02 18:26:23 +08:00
XiaXiaotian
42cefc173f refractor WiFi clock setting
Do not set WiFi clock in PHY initializing function, move it to WiFi
   start/stop function.
2017-11-02 15:24:21 +08:00
wangmengyang
bd6394db92 component/bt: clean up WIFI_CLK_EN_REG settings for Bluetooth
1. move settings of WIFI_CLK_EN_REG for bluetooth into controller init/deinit APIs
2. modify the bit mask used in phy_rf init/deinit to use WIFI-BT shared bits
2017-11-02 15:24:21 +08:00
Ivan Grokhotkov
9bfb45aa1d soc/rtc: fix increased current consumption in light sleep
This fixes a configuration issue of RTC, which caused light sleep current
to be 1.35mA instead of 0.85mA.
2017-11-02 13:57:26 +08:00
Ivan Grokhotkov
eb5752c635 esp_restart: fix possible race while stalling other CPU, enable WDT early
Previously esp_restart would stall the other CPU before enabling RTC_WDT.
If the other CPU was executing an s32c1i instruction, the lock signal
from CPU to the arbiter would still be held after CPU was stalled. If
the CPU running esp_restart would then try to access the same locked
memory pool, it would be stuck, because lock signal would never be
released.

With this change, esp_restart resets the other CPU before stalling it.
Ideally, we would want to reset the CPU and keep it in reset, but the
hardware doesn't have such feature for PRO_CPU (it is possible to hold
APP_CPU in reset using DPORT register). Given that ROM code will not use
s32c1i in the first few hundred cycles, doing reset and then stall seems
to be safe.

In addition to than, RTC_WDT initialization is moved to the beginning of
the function, to prevent possible lock-up if CPU stalling still has any
issue.
2017-10-26 19:53:53 +08:00
Ivan Grokhotkov
f11ad0c904 soc/rtc: fix spurious warnings about XTAL frequency on startup
1. Make sure that 8MD256 clock used to estimate XTAL frequency is enabled
   before trying to use rtc_clk_cal_ratio.
   This fixes "Bogus XTAL frequency: 0 MHz" warnings after software reset.

2. Don't call rtc_clk_xtal_freq_estimate if XTAL frequency is already
   known. This reduces startup time after deep sleep or software reset.

3. Compare known XTAL frequency and estimated one before printing a
   warning. This fixes "Possibly invalid CONFIG_ESP32_XTAL_FREQ setting
   (40MHz). Detected 40 MHz." warnings.
2017-10-26 19:53:53 +08:00
Ivan Grokhotkov
9317cb3434 soc/rtc: add tests for CPU frequency switching
These tests switch between PLL and XTAL frequencies for 10 seconds.
2017-10-26 19:53:53 +08:00
Ivan Grokhotkov
6d4ed4ff6c soc/rtc: wait for SLOW_CLK cycle when switching CPU clock
Previous implementation waited for 20us after setting
RTC_CNTL_SOC_CLK_SEL_XTL register, using ets_delay_us, assuming that
the CPU was running at XTAL frequency. In reality, clock switch happened
on the next RTC_SLOW_CLK cycle, and CPU could be running at the previous
frequency (for example, 240 MHz) until then.
ets_delay_us would wait for 20 us * 40 cycles per us = 800 CPU cycles
(assuming 40 MHz XTAL; even less with a 26 MHz XTAL).
But if CPU was running at 240 MHz, 800 cycles would pass in just 3.3us,
while SLOW_CLK cycle could happen as much as 1/150kHz = 6.7us after
RTC_CNTL_SOC_CLK_SEL_XTL was set. So the software would not actually wait
long enough for the clock switch to happen, and would disable the PLL
while CPU was still clocked from PLL, leading to a halt.

This implementation uses rtc_clk_wait_for_slow_cycle() function to wait
until the clock switch, removing the need to wait for a fixed number of
CPU cycles.
2017-10-26 19:53:53 +08:00
Ivan Grokhotkov
05a0fbd49b soc/rtc: add a function to wait for slow clock cycle
Some RTC features are synchronized to RTC_SLOW_CLK, so sometimes
software needs to wait for the next slow clock cycle.
This function implements waiting using Timer Group clock calibration
feature.
2017-10-26 19:53:53 +08:00
esp32de
7c0020bfd0 feat(adc2): append adc2 support and api and the lock with WIFI module
append adc support and api
- esp_err_t adc2_config_width(adc_bits_width_t width_bit);
- esp_err_t adc2_config_channel_atten(adc2_channel_t channel, adc_atten_t atten);
- int adc2_get_voltage(adc2_channel_t channel);
2017-10-26 14:35:29 +08:00
Ivan Grokhotkov
59b7d98fec Merge branch 'feature/dfs' into 'master'
Dynamic frequency scaling

See merge request !1189
2017-10-22 12:34:11 +08:00
Ivan Grokhotkov
b6f37bda97 Merge branch 'feature/i2s_built_in_adc' into 'master'
feature(I2S-ADC): add ADC mode for I2S.

See merge request !1077
2017-10-20 15:52:56 +08:00
Ivan Grokhotkov
099565635b soc: correct values of SOC_BYTE_ACCESSIBLE_LOW, SOC_MEM_INTERNAL_LOW
Internal byte accessible memory starts with Internal ROM 1 at 0x3FF90000.
Region of RTC fast memory starting at 0x3FF80000 is not used in IDF as
it is mapped to PRO CPU only.
2017-10-19 21:35:21 +08:00
Ivan Grokhotkov
fba9678c56 uart: add support for REF_TICK 2017-10-18 14:19:20 +08:00
Ivan Grokhotkov
b03e08dc4e soc/rtc: add function to convert CPU frequency in MHz to rtc_cpu_freq_t 2017-10-18 14:19:15 +08:00
Ivan Grokhotkov
a242ae6d0b soc/rtc: add fast paths for switching between PLL and XTAL 2017-10-18 14:19:14 +08:00
Jeroen Domburg
740f8a79f0 Add logic to make external RAM usable with malloc() 2017-09-28 17:17:50 +08:00
michael
9d9e771933 fix(global, log): fix esp_log(_early)_timestamp readings after startup by correct the CCOUNT register when switching CPU clock.
TW#13332, Closes #700
2017-09-26 15:18:17 +08:00
Tian Hao
3e2ee24e4f component/bt : support bluetooth controller DRAM release dynamically
1. remove CONFIG_BT_DRAM_RELEASE from Kconfig
2. add API to release bluetooth controller DRAM to heap
2017-09-21 14:31:20 +08:00