Closes: https://github.com/espressif/esp-idf/issues/9208
When I2S is configured into different modes, the slot sequence varies.
This commit updates slot sequence tables and corresponding descriptions
in (both code and programming guide).
When ESP32-C2 is paired with a 26 MHz XTAL, the systimer tick
frequency becomes equal to 26 / 2.5 = 10.4 MHz. Previously we always
assumed that systimer tick frequency is integer (and 1 MHz * power of
two, above that!).
This commit introduces a new LL macro, SYSTIMER_LL_TICKS_PER_US_DIV.
It should be set in such a way that:
1. SYSTIMER_LL_TICKS_PER_US / SYSTIMER_LL_TICKS_PER_US_DIV equals the
actual systimer tick frequency,
2. and SYSTIMER_LL_TICKS_PER_US is integer.
For ESP32-C2 this means that SYSTIMER_LL_TICKS_PER_US = 52 and
SYSTIMER_LL_TICKS_PER_US_DIV = 5.
This introduced two possible issues:
1. Overflow when multiplying systimer counter by 5
- Should not be an issue, since systimer counter is 52-bit, so
counter * 5 is no more than 55-bit.
2. The code needs to perform:
- divide by 5: when converting from microseconds to ticks
- divide by 52: when converting from ticks to microseconds
The latter potentially introduces a performance issue for the
esp_timer_get_time function.
When creating G0 layer, some regi2c_*.h headers were moved out from
esp_hw_support (G1) to soc (G0). In order to be consistent with that change,
move all the remaining regi2c_*.h headers to soc too.
In C++20, using the result of an assignment to a 'volatile' value is
deprecated.
Breaking change: register "setter" or modification macros can no
longer be used as expressions.
Closes https://github.com/espressif/esp-idf/issues/9170
This commit updates the esp_cpu.h API. The new API presents a new
abstraction of the CPU where CPU presents the following interfaces:
- CPU Control (to stall/unstall/reset the CPU)
- CPU Registers (to read registers commonly used in SW such as SP, PC)
- CPU Interrupts (to inquire/allocate/control the CPUs 32 interrupts)
- Memory Port (to configure the CPU's memory bus for memory protection)
- Debugging (to configure/control the CPU's debugging port)
Note: Also added FORCE_INLINE_ATTR to the DoxyFile in order to pass doc
builds for esp_cpu.h
created common Kconfig for common flag of nimbble and Bluedroid
fix compile error
created common cfg file for controller
fix the compilation error on tip of master
added common controller flags and fixed compilation error
sdkconfig rename for target specific
When enable sleep reject before this fix, we have two limitations:
1. it must be light sleep
2. RTC GPIO wakeup source must be set
We require light sleep because `esp_deep_sleep_start` function has
been declared with "noreturn" attribute, So developers don't expect
that this function may return (due to an error or a sleep reject).
But the requirement for RTC GPIO wakeup source is not reasonable for
all chips. This requirement exists because ESP32 only supports RTC GPIO
and SDIO sleep reject sources. But later chips support all sleep reject
sources.
This fix brings the following changes:
for ESP32: RTC GPIO and SDIO sleep reject sources can be enabled
when corresponding wakeup source is set.
for later chips: all sleep reject sources can be enabled when
corresponding wakeup source is set.
The legacy driver can't handle the breaking change between esp chips
very well.
And it's not elegant to extend new feature like DMA, ETM.
The new driver can return a opaque handle for each RMT channel.
An obvious transaction concept was also introduced.
TX and RX functionalities are splited out.
