Add a check in spi_master driver to prevent using both 'trans->length'
and 'trans->rxlength' on chips other than ESP32 and ESP32S2 which hardware
not support using both TX and RX phases in half-duplex mode
There are two ways to know which transaction descriptor is finished,
by either calling `spi_device_get_trans_result`, or getting it from `post_cb`.
When `SPI_DEVICE_NO_RETURN_RESULT` is set, driver will not push finished
transaction descriptors into the queue. So you can't get it from
`spi_device_get_trans_result`. The only way to know this is via `post_cb`.
update document for function `spi_bus_add_device`
Add this flag to select if returning done transaction descriptors from ISR.
You should get the finished transaction descriptor by the callback "post_cb"
if you using this flag, if not, same as the past.
Close https://github.com/espressif/esp-idf/pull/9141
1. Clean up clk usage in IDF, replace rtc_clk_xtal/apb_freq_get with
upper level API esp_clk_xtal/apb_freq
2. Fix small errors and wrong comments related to clock
3. Add clk_tree_defs.h to provide an unified clock id for each chip
Modify the NGed drivers to adopt new clock ids
The user can now request the chip select to remain active after the current
transfer. In order to do so, he MUST acquire the bus first with `spi_device_acquire_bus()`
function, else, an error is returned.
This commit seperates the hal context into different configuration
structures based on their members' definitions. Through refactoring
spi_master.c, the device related configuration should be passed in and
set each time before a new transaction. The transaction related
configuration now is a local variable in case of the fact that error
occurs without any notice when user forgets to pass new transaction
configuration in (which means the old driver will use the trans_config
that is saved from last transaction).
Besides, via above refactor, this commit fixs a bug which leads to
wrong cs polarity setting.
Closes https://github.com/espressif/esp-idf/pull/5490
Moreover, via above refactor, this commit also fixs a bug about duplex
mode switching when multiple devices are added to the bus.
Closes https://github.com/espressif/esp-idf/issues/4641
The SPI bus lock on SPI1 introduces two side effects:
1. The device lock for the main flash requires the
`CONFIG_FREERTOS_SUPPORT_STATIC_ALLOCATION` to be selected, however this
option is disabled by default in earlier IDF versions. Some developers
may find their project cannot be built by their old sdkconfig files.
2. Usually we don't need the lock on the SPI1 bus, due to it's
restrictions. However the overhead still exists in this case, the IRAM
cost for static version of semaphore functions, and the time cost when
getting and releasing the lock.
This commit:
1. Add a CONFIG_SPI_FLASH_BYPASS_MAIN_LOCK option, which will forbid the
space cost, as well as the initialization of the main bus lock.
2. When the option is not selected, the bus lock is used, the
`CONFIG_FREERTOS_SUPPORT_STATIC_ALLOCATION` will be selected explicitly.
3. Revert default value of `CONFIG_FREERTOS_SUPPORT_STATIC_ALLOCATION`
to `n`.
introduced in 49a48644e4.
Closes https://github.com/espressif/esp-idf/issues/5046
There are lot of prints of `Allocate TX buffer for DMA`
Changed these from `ESP_LOGI` to `ESP_LOGD`
Signed-off-by: Vikram Dattu <vikram.dattu@espressif.com>
Using xxx_periph.h in whole IDF instead of xxx_reg.h, xxx_struct.h, xxx_channel.h ... .
Cleaned up header files from unnecessary headers (releated to soc/... headers).
