remove duplicated include from components/esp32/incliude/esp_core_dump.h
espcoredump/incliude/esp_core_dump.h:
fix signature of the functions esp_core_dump_to_uart() and esp_core_dump_to_uart();
add espcoredump into COMPONENT_PRIV_REQUIRES list
fix linker.lf file
This commit removes trailing semicolons following a while(0) from
function-like macros in IDF. This will force those macros to be called
with a semicolon when called.
Added:
* set a secure version in app/bootloader.
* description anti-rollback to ota part
* emulate the secure_version write and read operations
* efuse_em partition.
* a description about a rollback for native_ota_example.
Closes: TW26335
Due to a hardware limitation in ESP32, the first four bytes of some
CSI data is invalid, not the last four bytes.
Correct a mistake of CSI sub-carrier index in documentation.
1. detect and fix root conflicts when router BSSID is not set.
2. when root can not connect to the router due to NO_MORE_STAS(reason code:5), root will stop re-connection and perform MESH_NWK_LOOK_FOR_NETWORK.
3. wifi: fix the disconnection caused by receiving a deauth frame from non-parent node during scanning.
4. fix routing table redundant issue.
5. modify the max routes limitation from 300 to 1000.
6. wifi: fix ap does not deauth sta which has not completed the 4-way handshake.
1. when no parent is found, send probe request via broadcast.
2. fix memory leak caused by the remove announcement being sent is not released when esp_mesh_stop() is called.
3. fix modify IE encrypt after mesh is started.
4. ignore esp_mesh_connect() if mesh automatic reconnection is enabled.
5. fix reason is cleared before vote is done.
* Prevents section type conflict errors if (say) const & non-const data
is put into the same section (ie with DRAM_ATTR)
* Allows linker --gc-sections to remove unused custom sections
1. start an esp_timer on entering sleep to acquire pm_lock before wake up from modem sleep
2. decrease the clock division of XTAL fed to bluetooth low power clock from 32us to 2us period to allow to work under 240MHz Max CPU frequency
3. decrease the minimum sleep duration threshold to allow shorter bluetooth modem sleep period, especially for BLE with short connection interval
4. reconfigure bluetooth baseband(BT-BB) settings after PHY/RF init upon waking up from modem sleep to avoid packet RX/TX performance degradation
1. Use BIT[7:5] of EID to determine psram size
2. Add ID support for 16Mbit psram
3. Remove module reset on SPI1
4. Confirmed with the vendor that only the old 32Mbit psram need special clock timing. For other psram chips, we should use standard QPI mode.
1. add network channel switch function.
- users can obtain the new channel through the event MESH_EVENT_CHANNEL_SWITCH.
- the entire network will be moved to the same channel as the router without user intervention.
- if no router is in the network, users can call esp_mesh_switch_channel() on the root side to
move the entire network to their desired channel.
2. support not configuring the network channel.
3. support not configuring the router BSSID even if the router is hidden.
4. add allow_channel_switch to mesh configuration.
- if the channel is not specified, this value will be ignored.
- if the channel is specified and this value is set, when "fail" (mesh_attempts_t) times of parent selection
or look for networks are reached, device will change to perform a full channel scan for networks that could join.
- if the channel is specified and this value is set to 0, when a root is not elected, channel switch is not allowed.
but when a root appears, the root performs a full channel scan during the process of connecting to the router,
so even allow_channel_switch is set to 0, the root may still switch channel and eventually the entire network
changes channel.
5. add allow_router_switch to mesh router configuration.
- if the BSSID of router is not specified, this value will be ignored.
- if the BSSID of router is specified and this value is set, when the router of this specified BSSID fails to be found
after "fail" (mesh_attempts_t) times, the entire network is allowed to switch to another router with the same SSID.
6. modify the root to perform a full channel scan when esp_wifi_connect().
7. support handling beacon without DS Paramter Set.
1. fix failture of mesh stop caused by block-sending.
2. fix when FIXED_ROOT is set, 2nd layer devices can not receive mesh event ESP_ERR_MESH_NO_PARENT_FOUND.
3. fix when FIXED_ROOT is set and the root turns off mesh function, 2nd layer devices do not look for new parents.
4. add APIs esp_mesh_disconnect() and esp_mesh_connect().
5. disconnect from parent/router when the DSSS channel in received beacon is different from the home channel.
6. remove nvs task to release 3k bytes memory.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
New unity component can be used for testing other applications.
Upstream version of Unity is included as a submodule.
Utilities specific to ESP-IDF unit tests (partitions, leak checking
setup/teardown functions, etc) are kept only in unit-test-app.
Kconfig options are added to allow disabling certain Unity features.
1. fix ap_loss that occurs when the parent turns off the mesh function and becomes a normal WiFi with a different SSID.
2. add an event MESH_EVENT_NETWORK_STATE that contains information about whether there is a root in the current network.
3. modify the mechanism of mesh IE update.
4. fix a problem in the process of re-voting to select the root, the device that does not meet the conditions of being a root votes for itself.
5. fix an issue that occurs in esp_mesh_recv_toDS() when stopping the mesh.
6. when the user specifies a parent for the device, the device will set the authmode and password of its AP mode to the same value as the specified parent.
7. add two disconnected reason codes MESH_REASON_EMPTY_PASSWORD and MESH_REASON_PARENT_UNENCRYPTED.
Routine `spi_flash_cache2phys` sometimes return incorrect value,
resulting in failure in getting currently running ota partition.
This in turn aborts firmware update process.This issue was more
prominent with SPIRAM enabled cases.
Fix ensures proper cache guards during `spi_flash_cache2phys`, and
also for few other similar APIs.
In addition, `esp_ota_get_running_partition` has also been optimized
to save currently running partition for subsequent invocations.
Fixes https://github.com/espressif/esp-idf/issues/2451
In some cases, when data was just written into UART FIFO, transmitter
state could be still zero while the FIFO did contain some data.
This resulted in uart_tx_wait_idle occasionally returning before all
the data was sent out.
Fix by checking both UART transmitter state and TX FIFO count.
