esp-idf/examples/ethernet/basic/README.md
Ondrej Kosta ef30384902 esp_eth: add support for multiple Ethernets modules at a time
Ethernet driver events properly bounded with ESP NETIF actions to support multiple Ethernet modules used at a time.

Components using Ethernet updated to conform with new API.

Closes https://github.com/espressif/esp-idf/issues/7318
2021-08-24 17:10:36 +02:00

3.7 KiB

Ethernet Example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

Overview

This example demonstrates basic usage of Ethernet driver together with tcpip_adapter. The work flow of the example could be as follows:

  1. Install Ethernet driver
  2. Send DHCP requests and wait for a DHCP lease
  3. If get IP address successfully, then you will be able to ping the device

If you have a new Ethernet application to go (for example, connect to IoT cloud via Ethernet), try this as a basic template, then add your own code.

How to use example

Hardware Required

To run this example, it's recommended that you have an official ESP32 Ethernet development board - ESP32-Ethernet-Kit. This example should also work for 3rd party ESP32 board as long as it's integrated with a supported Ethernet PHY chip. Up until now, ESP-IDF supports up to four Ethernet PHY: LAN8720, IP101, DP83848 and RTL8201, additional PHY drivers should be implemented by users themselves.

Besides that, esp_eth component can drive third-party Ethernet module which integrates MAC and PHY and provides common communication interface (e.g. SPI, USB, etc). This example will take the DM9051, W5500 or KSZ8851SNL SPI modules as an example, illustrating how to install the Ethernet driver in the same manner.

The ESP-IDF supports the usage of multiple Ethernet interfaces at a time when external modules are utilized which is also demonstrated by this example. There are several options you can combine:

  • Internal EMAC and one SPI Ethernet module.
  • Two SPI Ethernet modules of the same type connected to single SPI interface and accessed by switching appropriate CS.
  • Internal EMAC and two SPI Ethernet modules of the same type.

Pin Assignment

See common pin assignments for Ethernet examples from upper level.

When using two Ethernet SPI modules at a time, they are to be connected to single SPI interface. Both modules then share data (MOSI/MISO) and CLK signals. However, the CS, interrupt and reset pins need to be connected to separate GPIO for each Ethernet SPI module.

Configure the project

idf.py menuconfig

See common configurations for Ethernet examples from upper level.

Build, Flash, and Run

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT build flash monitor

(Replace PORT with the name of the serial port to use.)

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

I (394) eth_example: Ethernet Started
I (3934) eth_example: Ethernet Link Up
I (3934) eth_example: Ethernet HW Addr 30:ae:a4:c6:87:5b
I (5864) tcpip_adapter: eth ip: 192.168.2.151, mask: 255.255.255.0, gw: 192.168.2.2
I (5864) eth_example: Ethernet Got IP Address
I (5864) eth_example: ~~~~~~~~~~~
I (5864) eth_example: ETHIP:192.168.2.151
I (5874) eth_example: ETHMASK:255.255.255.0
I (5874) eth_example: ETHGW:192.168.2.2
I (5884) eth_example: ~~~~~~~~~~~

Now you can ping your ESP32 in the terminal by entering ping 192.168.2.151 (it depends on the actual IP address you get).

Troubleshooting

See common troubleshooting for Ethernet examples from upper level.

(For any technical queries, please open an issue on GitHub. We will get back to you as soon as possible.)