mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
70 lines
2.7 KiB
Markdown
70 lines
2.7 KiB
Markdown
| Supported Targets | ESP32 | ESP32-S2 | ESP32-S3 | ESP32-C3 |
|
|
| ----------------- | ----- | -------- | -------- | -------- |
|
|
|
|
# FATFS partition generation example
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This example demonstrates how to use the FATFS partition
|
|
generation tool [fatfsgen.py](../../../components/fatfs/fatfsgen.py) to automatically create a FATFS
|
|
filesystem image from the contents of a host folder during build, with an option of
|
|
automatically flashing the created image on invocation of `idf.py -p PORT flash`.
|
|
Beware that the minimal required size of the flash is 4 MB.
|
|
You can specify using menuconfig weather example will use read-only or read-write mode. The default option is read-write mode.
|
|
To change it just use menuconfig:
|
|
|
|
```shell
|
|
idf.py menuconfig
|
|
```
|
|
|
|
Then select `Example Configuration` a chose `Mode for generated FATFS image` either `Read-Write Mode` or `Read-Only Mode`.
|
|
`Read-Only` option indicates generating raw fatfs image without wear levelling support.
|
|
On the other hand, for `Read-Write` the generated fatfs image will support wear levelling thus can be mounted in read-write mode.
|
|
|
|
|
|
The following gives an overview of the example:
|
|
|
|
1. There is a directory `fatfs_image` from which the FATFS filesystem image will be created.
|
|
|
|
2. The function `fatfs_create_rawflash_image` is used to specify that a FATFS image
|
|
should be created during build for the `storage` partition.
|
|
For CMake, it is called from [the main component's CMakeLists.txt](./main/CMakeLists.txt).
|
|
`FLASH_IN_PROJECT` specifies that the created image
|
|
should be flashed on invocation of `idf.py -p PORT flash` together with app, bootloader, partition table, etc.
|
|
The image is created on the example's build directory with the output filename `storage.bin`.
|
|
|
|
3. Upon invocation of `idf.py -p PORT flash monitor`, application loads and
|
|
finds there is already a valid FATFS filesystem in the `storage` partition with files same as those in `fatfs_image` directory. The application is then
|
|
able to read those files.
|
|
|
|
## How to use example
|
|
|
|
### Build and flash
|
|
|
|
To run the example, type the following command:
|
|
|
|
```CMake
|
|
# CMake
|
|
idf.py -p PORT flash monitor
|
|
```
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example output
|
|
|
|
Here is the example's console output:
|
|
|
|
```
|
|
...
|
|
I (322) example: Mounting FAT filesystem
|
|
I (332) example: Reading file
|
|
I (332) example: Read from file: 'this is test'
|
|
I (332) example: Unmounting FAT filesystem
|
|
I (342) example: Done
|
|
```
|
|
|
|
The logic of the example is contained in a [single source file](./main/fatfsgen_example_main.c),
|
|
and it should be relatively simple to match points in its execution with the log outputs above.
|