da471dfcd1
Updated main examples README to add missing examples folders and Getting Started links Updated wifi/fastscan example README Updated wifi examples README Updated wifi main examples README Added instructions and removed obviousness from examples README Updates on example README in peripherals, system and wifi Updates on example README in peripherals and added wave form pictures on wave_gen example Updates and review on example README Revision on unit style convention Added the getting started link for each supported version Readme review and recommended enhancements Added the default note on the wave form option info Added the ESP32-C3 support information on the temperature sensor example README Added Getting Started information for ESP32-S2 and ESP32-C3 Issue fixed on the supported target on README Resolved merge conflict
3.2 KiB
Wi-Fi Scan Example
(See the README.md file in the upper level 'examples' directory for more information about examples.)
This example shows how to scan for available set of APs.
How to use example
Before project configuration and build, be sure to set the correct chip target using idf.py set-target <chip_name>.
Hardware Required
- A development board with ESP32/ESP32-S2/ESP32-C3 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.).
- A USB cable for Power supply and programming.
Configure the project
Open the project configuration menu (idf.py menuconfig).
In the Example Configuration menu:
- Set the Example configuration.
- Use
Max size of scan listto set the maximum nunber of access points in the list.
- Use
Build and Flash
Build the project and flash it to the board, then run the monitor tool to view the serial output:
Run idf.py -p PORT flash monitor to build, flash and monitor the project.
(To exit the serial monitor, type Ctrl-].)
See the Getting Started Guide for all the steps to configure and use the ESP-IDF to build projects.
- ESP-IDF Getting Started Guide on ESP32
- ESP-IDF Getting Started Guide on ESP32-S2
- ESP-IDF Getting Started Guide on ESP32-C3
Example Output
As you run the example, you will see the following log:
I (443) wifi:wifi firmware version: 6bff005
I (443) wifi:wifi certification version: v7.0
I (443) wifi:config NVS flash: enabled
I (443) wifi:config nano formating: disabled
I (453) wifi:Init data frame dynamic rx buffer num: 32
I (453) wifi:Init management frame dynamic rx buffer num: 32
I (463) wifi:Init management short buffer num: 32
I (463) wifi:Init dynamic tx buffer num: 32
I (473) wifi:Init static tx FG buffer num: 2
I (473) wifi:Init static rx buffer size: 1600
I (473) wifi:Init static rx buffer num: 10
I (483) wifi:Init dynamic rx buffer num: 32
I (483) wifi_init: rx ba win: 6
I (493) wifi_init: tcpip mbox: 32
I (493) wifi_init: udp mbox: 6
I (493) wifi_init: tcp mbox: 6
I (503) wifi_init: tcp tx win: 5744
I (503) wifi_init: tcp rx win: 5744
I (513) wifi_init: tcp mss: 1440
I (513) wifi_init: WiFi IRAM OP enabled
I (513) wifi_init: WiFi RX IRAM OP enabled
I (533) phy_init: phy_version 300,6e46ba7,Jan 25 2021
I (683) wifi:set rx active PTI: 0, rx ack PTI: 0, and default PTI: 0
I (683) wifi:mode : sta (7c:df:a1:40:23:84)
I (683) wifi:enable tsf
I (2783) scan: Total APs scanned = 17
I (2783) scan: SSID IoTNetwork
I (2783) scan: RSSI -50
I (2783) scan: Authmode WIFI_AUTH_WPA2_PSK
I (2783) scan: Pairwise Cipher WIFI_CIPHER_TYPE_CCMP
I (2793) scan: Group Cipher WIFI_CIPHER_TYPE_CCMP
I (2793) scan: Channel 5
I (2883) scan: SSID TP-Link_6872
I (2883) scan: RSSI -70
I (2883) scan: Authmode WIFI_AUTH_WPA_WPA2_PSK
I (2893) scan: Pairwise Cipher WIFI_CIPHER_TYPE_CCMP
I (2893) scan: Group Cipher WIFI_CIPHER_TYPE_CCMP
I (2903) scan: Channel 11
...
Troubleshooting
For any technical queries, please open an issue on GitHub. We will get back to you soon.