esp-idf/examples/zigbee/light_sample/HA_on_off_switch/README.md
likunqiao b699d8fd6b zigbee: update Zigbee example signal handler API
* update API for new esp-zigbee-lib
* enable ci test
2022-11-21 15:39:57 +08:00

2.7 KiB

Supported Targets ESP32-H4

Light Switch Example

This test code shows how to configure Zigbee Coordinator and use it as an HA on/off_switch

Hardware Required

  • One development board with ESP32-H4 SoC acting as Zigbee Coordinator (loaded with HA_on_off_switch)
  • A USB cable for power supply and programming
  • Choose another ESP32-H4 as Zigbee end-device (see HA_on_off_light)

Configure the project

Before project configuration and build, make sure to set the correct chip target using idf.py set-target esp32h4.

Erase the NVRAM

Before flash it to the board, it is recommended to erase NVRAM if user doesn't want to keep the previous examples or other projects stored info using idf.py -p PORT erase-flash

Build and Flash

Build the project, flash it to the board, and start the monitor tool to view the serial output by running idf.py -p PORT flash monitor.

(To exit the serial monitor, type Ctrl-].)

Example Output

As you run the example, you will see the following log:

light switch:

I (318) gpio: GPIO[9]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:2
I (328) system_api: Base MAC address is not set
I (328) system_api: read default base MAC address from EFUSE
I (408) phy: libbtbb version: 6c47ec3, Mar 16 2022, 18:54:24
I (408) phy: phy_version: 101, bb2a234, Mar 16 2022, 18:54:11
I (818) ESP_ZB_ON_OFF_SWITCH: status: 255
I (818) ESP_ZB_ON_OFF_SWITCH: Zigbee stack initialized
I (818) ESP_ZB_ON_OFF_SWITCH: Start network formation
I (1318) ESP_ZB_ON_OFF_SWITCH: Formed network successfully (Extended PAN ID: ff:fc:7c:c0:f0:bd:97:10, PAN ID: 0x88e7)
I (1778) ESP_ZB_ON_OFF_SWITCH: status: 0
I (5528) ESP_ZB_ON_OFF_SWITCH: status: 0
I (6038) ESP_ZB_ON_OFF_SWITCH: status: 0
I (6068) ESP_ZB_ON_OFF_SWITCH: New device commissioned or rejoined (short: 0x2878)
I (6098) ESP_ZB_ON_OFF_SWITCH: User find cb: address:0x2878, endpoint:10
I (6638) ESP_ZB_ON_OFF_SWITCH: status: 0
I (6678) ESP_ZB_ON_OFF_SWITCH: status: 0
I (8168) ESP_ZB_ON_OFF_SWITCH: send move to on_off toggle command
I (8898) ESP_ZB_ON_OFF_SWITCH: send move to on_off toggle command
I (9458) ESP_ZB_ON_OFF_SWITCH: send move to on_off toggle command
I (10088) ESP_ZB_ON_OFF_SWITCH: send move to on_off toggle command
I (10588) ESP_ZB_ON_OFF_SWITCH: send move to on_off toggle command
I (11098) ESP_ZB_ON_OFF_SWITCH: send move to on_off toggle command

Light Control Functions

  • By toggling the switch button (BOOT) on this board, the LED on the board loaded with the HA_on_off_light example will turn on and off.

Troubleshooting

For any technical queries, please open an issue on GitHub. We will get back to you soon.