mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
18 KiB
18 KiB
| Supported Targets | ESP32 | ESP32-C3 | ESP32-C6 | ESP32-H2 | ESP32-S3 |
|---|
I2S Basic PDM Mode Example
(See the README.md file in the upper level 'examples' directory for more information about examples.)
This example is going to show how to use the PDM TX and RX mode.
How to Use Example
Hardware Required
General
- A development board with any supported Espressif SOC chip (see
Supported Targetstable above) - A USB cable for power supply and programming
PDM RX
- For non-ESP32-S3 SoC, a PDM microphone whose
selpin is supposed to be pulled down, and connecting itsclkpin toEXAMPLE_PDM_RX_CLK_IO,datapin toEXAMPLE_PDM_RX_DIN_IO.
┌───────────────────────┐ ┌──────────────────┐
│ ESP │ │ PDM microphone │
│ │ PDM clock │ │
│ EXAMPLE_PDM_RX_CLK_IO ├──────────────►│ CLK │
│ │ PDM data │ │
│ EXAMPLE_PDM_RX_DIN_IO │◄──────────────┤ DATA │
│ │ │ │
│ │ ┌─────┤ SEL │
│ │ │ │ │
│ GND ├─────────┴─────┤ GND │
│ │ │ │
│ VCC ├───────────────┤ VCC │
└───────────────────────┘ └──────────────────┘
- For ESP32-S3 SoC, this example shows how to support 8 PDM microphones, in this case, the connection can be:
┌──────────────────┐ ┌─────────────────────────┐ ┌──────────────────┐
│ PDM microphone3 │ │ ESP │ │ PDM microphone1 │
│ │ PDM clock │ │ PDM clock │ │
│ CLK │◄───┬───────────────────┤ EXAMPLE_PDM_RX_CLK_IO ├───────────────────┬───►│ CLK │
│ │ │ │ │ │ │ │
│ DATA ├────┼────┐ │ EXAMPLE_PDM_RX_DIN_IO │◄─────────────┬────┼────┤ DATA │
│ │ │ │ │ │ │ │ │ │
│ SEL ├────┼────┼─────────┐ │ │ ┌─────────┼────┼────┤ SEL │
│ │ │ │ │ │ │ │ │ │ │ │
│ GND ├────┼────┼────┐ │ │ │ │ ┌────┼────┼────┤ GND │
│ │ │ │ │ │ │ │ │ │ │ │ │ │
│ VCC ├────┼────┼────┼────┤ │ │ ├────┼────┼────┼────┤ VCC │
└──────────────────┘ │ │ │ │ │ │ │ │ │ │ └──────────────────┘
│ │ │ │ │ │ │ │ │ │
┌──────────────────┐ │ │ │ │ │ │ │ │ │ │ ┌──────────────────┐
│ PDM microphone4 │ │ │ │ │ │ │ │ │ │ │ │ PDM microphone2 │
│ │ │ │ │ │ │ │ │ │ │ │ │ │
│ CLK │◄───┤ │ │ │ │ │ │ │ │ ├───►│ CLK │
│ │ │ │ │ │ │ │ │ │ │ │ │ │
│ DATA ├────┼────┴────┼────┼───►│ EXAMPLE_PDM_RX_DIN1_IO │ │ │ └────┼────┤ DATA │
│ │ │ │ │ │ │ │ │ │ │ │
│ SEL ├────┼─────────┤ │ │ │ │ ├─────────┼────┤ SEL │
│ │ │ │ │ │ │ │ │ │ │ │
│ GND ├────┼─────────┤ │ │ │ │ ├─────────┼────┤ GND │
│ │ │ │ │ │ │ │ │ │ │ │
│ VCC ├────┼─────────┼────┤ │ │ ├────┼─────────┼────┤ VCC │
└──────────────────┘ │ │ │ │ │ │ │ │ └──────────────────┘
│ │ │ │ │ │ │ │
┌──────────────────┐ │ │ │ │ │ │ │ │ ┌──────────────────┐
│ PDM microphone7 │ │ │ │ │ │ │ │ │ │ PDM microphone5 │
│ │ │ │ │ │ │ │ │ │ │ │
│ CLK │◄───┤ │ │ │ │ │ │ ├───►│ CLK │
│ │ │ │ │ │ │ │ │ │ │ │
│ DATA ├────┼────┐ │ │ │ EXAMPLE_PDM_RX_DIN2_IO │◄───┼────┼────┬────┼────┤ DATA │
│ │ │ │ │ │ │ │ │ │ │ │ │ │
│ SEL ├────┼────┼────┼────┤ │ │ ├────┼────┼────┼────┤ SEL │
│ │ │ │ │ │ │ │ │ │ │ │ │ │
│ GND ├────┼────┼────┤ │ │ │ │ ├────┼────┼────┤ GND │
│ │ │ │ │ │ │ │ │ │ │ │ │ │
│ VCC ├────┼────┼────┼────┤ │ │ ├────┼────┼────┼────┤ VCC │
└──────────────────┘ │ │ │ │ │ │ │ │ │ │ └──────────────────┘
│ │ │ │ │ │ │ │ │ │
┌──────────────────┐ │ │ │ │ │ │ │ │ │ │ ┌──────────────────┐
│ PDM microphone8 │ │ │ │ │ │ │ │ │ │ │ │ PDM microphone6 │
│ │ │ │ │ │ │ │ │ │ │ │ │ │
│ CLK │◄───┘ │ │ │ │ │ │ │ │ └───►│ CLK │
│ │ │ │ │ │ │ │ │ │ │ │
│ DATA ├─────────┴────┼────┼───►│ EXAMPLE_PDM_RX_DIN3_IO │ │ │ └─────────┤ DATA │
│ │ │ │ │ │ │ │ │ │
│ SEL ├──────────────┤ │ │ │ │ ├──────────────┤ SEL │
│ │ │ │ │ │ │ │ │ │
│ GND ├──────────────┴────┼────┤ GND ├────┼────┴──────────────┤ GND │
│ │ │ │ │ │ │ │
│ VCC ├───────────────────┴────┤ VCC ├────┴───────────────────┤ VCC │
└──────────────────┘ └─────────────────────────┘ └──────────────────┘
PDM TX
- An earphone or a speaker
- An audio power amplifier that can input PDM signal. If the power amplifier can only receive the analog signal without PDM clock (i.e. DAC line mode, otherwise codec line mode), a low-pass passive or active filter is required to restore the PDM data wave into analog signal, before it is transmitted to the power amplifier.
MAX98358 (codec case)
Please refer to the Datasheet of MAX98358 for more details.
┌────────────────────────┐ ┌───────────────┐
│ ESP │ │ MAX 98358 │
│ │ PDM clock │ │
│ EXAMPLE_PDM_TX_CLK_IO ├──────────────►│ CLK │ ┌─────────┐
│ │ PDM data │ │ │ Speaker │
│ EXAMPLE_PDM_TX_DOUT_IO ├──────────────►│ DATA OUTP ├───┤ │
│ │ │ │ │ │
│ │ ┌─────┤ SD_MODE OUTN ├───┤ │
│ │ │ │ │ │ │
│ VCC ├─────────┴─────┤ VCC │ └─────────┘
│ │ │ │
│ GND ├───────────────┤ GND │
└────────────────────────┘ └───────────────┘
NS4150 (dac case)
Please refer to the NS4150 datasheet for more details.
┌────────────────────────┐ ┌───────────────┐
│ ESP │ │ NS 4150 │
│ │ │ │
│ EXAMPLE_PDM_TX_CLK_IO │(No need to connect) │ INN │ ┌─────────┐
│ │PDM data┌────────────────┐ │ │ │ Speaker │
│ EXAMPLE_PDM_TX_DOUT_IO ├────────┤ Low-pass Filter├───►│ INP VoP ├───┤ │
│ │ └────────────────┘ │ │ │ │
│ │ ┌───┤ CTRL VoN ├───┤ │
│ │ │ │ │ │ │
│ VCC ├──────────────────────────┴───┤ VCC │ └─────────┘
│ │ │ │
│ GND ├──────────────────────────────┤ GND │
└────────────────────────┘ └───────────────┘
Configure the Project
PDM can only works in simplex mode, you can select the PDM direction in the menu config, or just setting the macro EXAMPLE_PDM_DIR directly. Setting it to EXAMPLE_PDM_TX or EXAMPLE_PDM_RX can choose the PDM direction of this example. But currently ESP32-C3 does not support PDM RX mode.
Build and Flash
Build the project and flash it to the board, then run monitor tool to view serial output:
idf.py -p PORT build flash monitor
(To exit the serial monitor, type Ctrl-].)
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
Example Output
PDM TX
While EXAMPLE_PDM_DIR is set to EXAMPLE_PDM_TX, then you can see the following log:
I2S PDM TX example start
---------------------------
D (284) i2s_common: tx channel is registered on I2S0 successfully
D (294) i2s_common: DMA malloc info: dma_desc_num = 6, dma_desc_buf_size = dma_frame_num * slot_num * data_bit_width = 500
D (304) i2s_pdm: Clock division info: [sclk] 160000000 Hz [mdiv] 3 [mclk] 49152000 Hz [bdiv] 8 [bclk] 6144000 Hz
D (314) i2s_pdm: The tx channel on I2S0 has been initialized to PDM TX mode successfully
D (324) i2s_common: i2s tx channel enabled
Playing bass `twinkle twinkle little star`
Playing alto `twinkle twinkle little star`
Playing treble `twinkle twinkle little star`
...
You can hear the audio 'twinkle twinkle little star' in three tones if you connect a speaker to it.
PDM RX
While EXAMPLE_PDM_DIR is set to EXAMPLE_PDM_RX, but without connecting a PDM microphone, then you can see the following log:
I2S PDM RX example start
---------------------------
D (10) i2s_common: rx channel is registered on I2S0 successfully
D (10) i2s_common: DMA malloc info: dma_desc_num = 6, dma_desc_buf_size = dma_frame_num * slot_num * data_bit_width = 500
D (20) i2s_common: i2s rx channel enabled
Read Task: i2s read 2048 bytes
-----------------------------------
[0] -6595 [1] 0 [2] -29199 [3] -32768
[4] -30203 [5] -32156 [6] -30704 [7] -31348
Read Task: i2s read 2048 bytes
-----------------------------------
[0] -30935 [1] -30935 [2] -30935 [3] -30935
[4] -30935 [5] -30935 [6] -30935 [7] -30935
Read Task: i2s read 2048 bytes
-----------------------------------
[0] -30935 [1] -30935 [2] -30935 [3] -30935
[4] -30935 [5] -30935 [6] -30935 [7] -30935
And only if you connect a PDM microphone, you can see the data changes:
I2S PDM RX example start
---------------------------
D (10) i2s_common: rx channel is registered on I2S0 successfully
D (10) i2s_common: DMA malloc info: dma_desc_num = 6, dma_desc_buf_size = dma_frame_num * slot_num * data_bit_width = 500
D (20) i2s_common: i2s rx channel enabled
Read Task: i2s read 2048 bytes
-----------------------------------
[0] -3181 [1] 0 [2] -7194 [3] -24288
[4] -777 [5] 3650 [6] 109 [7] 571
Read Task: i2s read 2048 bytes
-----------------------------------
[0] 2391 [1] 2378 [2] 2397 [3] 2385
[4] 2399 [5] 2375 [6] 2401 [7] 2389
Troubleshooting
For any technical queries, please open an issue on GitHub. We will get back to you soon.