10 KiB
| Supported Targets | ESP32-P4 |
|---|
Camera display plus ISP via DSI example
Overview
This example demonstrates how to use the ISP (image signal processor) to work with esp_driver_cam component. This example will capture camera sensor signals via CSI interface and display it via DSI interface. This example enables
- ISP AF (auto-focus) feature
- ISP BF (bayer denoise) feature
- ISP Sharpen feature
Usage
The subsections below give only absolutely necessary information. For full steps to configure ESP-IDF and use it to build and run projects, see ESP-IDF Getting Started.
Hardware Required
This example requires:
-
OV5647 camera sensor with VCM (Voice Coil Motor). The VCM used in this example is DW9714.
-
ILI9881C LCD screen
-
ESP32P4 devkit
GND GND ┌────────────────────────────────────────────────┐ ┌─────────────────────────────────────────────────────────┐ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ┌───────────────┴─────────────┴──────────────────┐ │ │ │ │ ┌──────────┴───────────┐ │ │ │ DSI DATA 1P │ │ │ │ ├───────────────────────────┤ │┌───────────┴─────────┐ CSI DATA 1P │ │ │ │ │ ├──────────────────────┤ │ DSI DATA 1N │ │ │ │ │ ├───────────────────────────┤ │ │ │ CSI DATA 1N │ ESP32-P4 │ │ │ │ OV5647 ├──────────────────────┤ │ DSI CLK N │ ILI9881C │ │ │ │ ├───────────────────────────┤ │ │ │ CSI CLK N │ │ │ │ │ ├──────────────────────┤ │ DSI CLK P │ │ │ │ │ ├───────────────────────────┤ │ │ │ CSI CLK P │ │ │ │ │ ├──────────────────────┤ │ DSI DATA 0P │ │ │ │ │ ├───────────────────────────┤ │ │ │ CSI DATA 0P │ │ │ │ │ ├──────────────────────┤ │ DSI DATA 0N │ │ │ │ │ ├───────────────────────────┤ │ │ │ CSI DATA 0N │ │ │ │ │ ├──────────────────────┤ │ └──────────────────────┘ │ │ │ │ └───────┬──┬──────────┘ │ │ │ │ I2C SCL │ │ │ └─────────────────────────────────┤ │ │ I2C SDA │ │ └────────────────────────────────────┤ │ └────────────────────────────────────────────────┘
Set Chip Target
First of all, your target must be supported by both:
- By your ESP-IDF version: For the full list of supported targets, run:
idf.py --list-targets - By this example: For the full list of supported targets, refer to the supported targets table at the top of this README.
After you make sure that your target is supported, go to your example project directory and set the chip target:
idf.py set-target <target>
For example, to set esp32-P4 as the chip target, run:
idf.py set-target esp32p4
Configure the Project
For information about Kconfig options, see Project Configuration > Name of relevant section(s).
To conveniently check or modify Kconfig options for this example in a project configuration menu, run:
idf.py menuconfig
Set CONFIG_CAMERA_OV5647 to y
Build and Flash
Execute the following command to build the project, flash it to your development board, and run the monitor tool to view the serial output:
idf.py build flash monitor
This command can be reduced to idf.py flash monitor.
If the above command fails, check the log on the serial monitor which usually provides information on the possible cause of the issue.
To exit the serial monitor, use Ctrl + ].
Example Output
If you see the following console output, your example should be running correctly:
I (1085) main_task: Calling app_main()
I (1095) ili9881c: ID1: 0x98, ID2: 0x81, ID3: 0x5c
I (1125) gpio: GPIO[31]| InputEn: 1| OutputEn: 1| OpenDrain: 1| Pullup: 1| Pulldown: 0| Intr:0
I (1125) gpio: GPIO[34]| InputEn: 1| OutputEn: 1| OpenDrain: 1| Pullup: 1| Pulldown: 0| Intr:0
I (1295) ov5647: Detected Camera sensor PID=0x5647 with index 0
I (1305) cam_dsi: fmt[0].name:MIPI_2lane_24Minput_RAW8_800x1280_50fps
I (1305) cam_dsi: fmt[1].name:MIPI_2lane_24Minput_RAW8_800x640_50fps
I (1315) cam_dsi: fmt[2].name:MIPI_2lane_24Minput_RAW8_800x800_50fps
I (1355) cam_dsi: Format in use:MIPI_2lane_24Minput_RAW8_800x640_50fps
You will also see the screen auto-focus when the screen image changes.
Reference
- Link to the ESP-IDF camera controller driver API reference, ESP-IDF: Camera Controller Driver
- Link to the ESP-IDF ISP driver API reference, ESP-IDF: Image Signal Processor
- ESP-IDF Getting Started
- Project Configuration (Kconfig Options)