mirror of https://github.com/espressif/esp-idf.git synced 2024-10-05 20:47:46 -04:00

MCPWM/capture: API workflow optimization

deprecate isr_register to introduce new callback based API, with framework managed interrupt routine
new HC-SR04 example

2021-08-05 19:12:58 +08:00

3.4 KiB

Raw Blame History

Supported Targets	ESP32	ESP32-S3

HC-SR04 Example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

The capture module in MCPWM peripheral is designed to accurately log the time stamp on the hardware side when an event happens (compared to GPIO ISR which requires a software-based logging method). Each capture unit has three channels, which can be used together to capture IO events parallelly. This example shows how to make use of the HW features to decode the pulse width signals generated from a common HC-SR04 sonar range finder -- HC-SR04.

The signal that HC-SR04 produces (and what can be handled by this example) is a simple pulse whose width indicates the measured distance. A pulse is required to send to HC-SR04 on Trig pin to begin a new measurement. Then the pulse described above will be sent back on Echo pin for decoding.

Typical signals:

Trig       +-----+
           |     |
           |     |
      -----+     +-----------------------
Echo                   +-----+
                       |     |
                       |     |
      -----------------+     +-----------

 +--------------------------------------->
                Timeline

How to Use Example

Hardware Required

An ESP development board
HC-SR04 module

Connection :

        +------+              +---------------------------------+
+-------+      |              |                                 |
|       |  VCC +--------------+ 5V                              |
+-------+      |              |                                 |
        + Echo +----=====>----+ GPIO18 (internal pull up)       |
        |      |              |                                 |
        + Trig +----<=====----+ GPIO19                          |
+-------|      |              |                                 |
|       |  GND +--------------+ GND                             |
+-------|      |              |                                 |
        +------+              +---------------------------------+

Build and Flash

Run idf.py -p PORT flash monitor to build, flash and monitor the project.

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

I (314) hc-sr04: HC-SR04 example based on capture function from MCPWM
I (324) hc-sr04: Echo pin configured
I (324) gpio: GPIO[19]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0 
I (334) hc-sr04: Trig pin configured
I (344) hc-sr04: trig task started
I (444) hc-sr04: Pulse width: 419us, Measured distance: 7.22cm
I (544) hc-sr04: Pulse width: 419us, Measured distance: 7.22cm
I (644) hc-sr04: Pulse width: 416us, Measured distance: 7.17cm
I (744) hc-sr04: Pulse width: 415us, Measured distance: 7.16cm
I (844) hc-sr04: Pulse width: 415us, Measured distance: 7.16cm
I (944) hc-sr04: Pulse width: 416us, Measured distance: 7.17cm
I (1044) hc-sr04: Pulse width: 391us, Measured distance: 6.74cm

This example runs at 10Hz sampling rate. out of range data is dropped and only valid measurement is printed.

Troubleshooting

For any technical queries, please open an [issue] (https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.

3.4 KiB Raw Blame History