11 KiB
| Supported Targets | ESP32-C6 | ESP32-H2 |
|---|
IEEE802.15.4 Command Line Example
This example demonstrates an IEEE802.15.4 Command Line. The IEEE802.15.4 CLI exposes configuration and management APIs via a command line interface.
How to use example
Hardware Required
To run this example, a board with IEEE 802.15.4 module (for example ESP32-H2) is required.
Configure the project
idf.py menuconfig
The example can run with the default configuration. IEEE802.15.4 Command Line is enabled with UART as the default interface. Additionally, USB JTAG is also supported and can be activated through the menuconfig:
Component config → ESP System Settings → Channel for console output → USB Serial/JTAG Controller
Build, Flash, and Run
Build the project and flash it to the board, then run monitor tool to view serial output:
idf.py -p PORT build flash monitor
Now you'll get an IEEE802.15.4 command line shell.
IEEE802.15.4 Command List
- cca
- channel
- coordinator
- ed
- esp154
- extaddr
- free
- heap
- panid
- pending
- promisc
- reg
- restart
- rx
- shortaddr
- tx
- txpower
- version
- help
IEEE802.15.4 Command Details
Most of the commands are available in both full and abbreviated form.
For example, to enable the receive mode, both rx -r 1 and rx --receive=1 are valid
> rx -r 1
I (4227508) i154cmd: RX Start
> rx --receive=1
I (4249898) i154cmd: RX Start
Only abbreviated formats are described below.
cca
cca -g
Get the cca cfg.
> cca -g
I (2676818) i154cmd: threshold:-60 dB, mode: 1
cca -m <mode>
Set the cca mode.
- 0: carrier
- 1: ED
- 2: carrier or ED
- 3: carrier and ED
> cca -m 1
I (5047618) i154cmd: set cca mode as: 1
cca -v <value>
Set the cca threshold.
> cca -v 60
I (4731648) i154cmd: set cca threshold as: 60
channel
channel -g
Get the channel number.
> channel -g
I (67238) i154cmd: current channel: 11
channel -s <n>
Set the channel number.
> channel -s 21
I (220268) i154cmd: set channel: 21
coordinator
coordinator -d
Enable the coordinator.
> coordinator -d
I (438228) i154cmd: hardware coordinator is disabled
coordinator -e
Disable the coordinator.
> coordinator -e
I (453288) i154cmd: hardware coordinator is enabled
coordinator -g
Get the coordinator.
> coordinator -g
I (472398) i154cmd: hardware coordinator was enabled
ed
ed -d <duration>
Configure the duration of energy detection.
> ed -d 2
I (668548) i154cmd: ed start
I (668548) i154cmd: ed_scan_rss_value: -98 dB
I (472398) i154cmd: hardware coordinator was enabled
esp154
esp154 -e
Enable initialize the IEEE 802.15.4 subsystem.
> esp154 -e
I (87127) i154cmd: initialize the IEEE 802.15.4 subsystem
esp154 -d
Disable initialize the IEEE 802.15.4 subsystem.
> esp154 -d
I (97107) i154cmd: deinitialize the IEEE 802.15.4 subsystem
extaddr
extaddr <extaddr>
Set the device extended address.
> extaddr 0xaa 0xbb 0xcc 0xdd 0x00 0x11 0x22 0x33
I (704937) i154cmd: set extaddr: 33221100ddccbbaa
extaddr -g
Get the device extended address.
> extaddr -g
I (615587) i154cmd: get extaddr: 0807060504030201
free
Get the current size of free heap memory.
> free
235024
heap
Get minimum size of free heap memory that was available during program execution.
> heap
min heap size: 231076
panid
panid <panid>
Set the device Pan ID.
> panid 0x1234
I (1112117) i154cmd: set panid: 0x1234
panid -g
Get the device Pan ID.
> panid -g
I (1128457) i154cmd: current panid: 0x1234
pending
pending <addr>
Add the address to pending table (2 bytes for short address, 8 bytes for extended address).
> pending 0x34 0x12
I (1806327) i154cmd: add pending shortaddr: 0x1234
pending -m <mode>
Set the autopending mode.
- 0: disable
- 1: enable
- 2: enhanced
> pending -m 1
I (1828817) i154cmd: set auto pending mode as: 1
pending -g
Get the autopending mode.
> pending -g
I (2007797) i154cmd: get auto pending mode as: 1
pending -r
Reset the pending address table.
> pending -r
I (2113377) i154cmd: clear the pending address table
pending -d
Delete the address from pending table (2 bytes for short address, 8 bytes for extended address).
> pending -d 0x34 -d 0x12
I (2322787) i154cmd: delete pending shortaddr: 0x1234
promisc
promisc [-edg]
- e: Enable the promiscuous mode.
- d: Disable the promiscuous mode.
- g: Get the promiscuous mode.
> promisc -e
I (2599357) i154cmd: promiscuous mode is enabled
> promisc -d
I (2600977) i154cmd: promiscuous mode is disabled
> promisc -g
I (2602927) i154cmd: hardware promiscuous mode was disabled
reg
reg -w <address> -v <value>
Write the register <address> with <value>.
> reg -w 0x0184 -v 0x00
I (103917) i154cmd: write reg 0x184: 0x1234
reg -r <address>
Read the register <address>.
> reg -r 0x0184
I (220967) i154cmd: reg 0x184 value: 0x1234
restart
Restart the program.
rx
rx -r <mode>
Configure the radio receive mode.
- 0: disable
- 1: enable
> rx -r 1
I (121977) i154cmd: RX Start
> rx -r 0
I (127267) i154cmd: radio exit receive mode
shortaddr
shortaddr <shortaddr>
set the device short address.
> shortaddr 0x1234
I (543167) i154cmd: set shortaddr: 0x1234
shortaddr -g
> shortaddr -g
I (568387) i154cmd: current shortaddr: 0x1234
tx
tx <n>
Transmit IEEE 802154 MAC frame.
- -C: Set cca trigging tx mode true.
> tx 0x00 0x11 0x22 0x33 0x44 0x55 0x66 0x77
I (6399947) i154cmd: tx sfd done, Radio state: 4
I (6399957) i154cmd: Tx Done 8 bytes
I (6399957) i154cmd: 00 11 22 33 44 55 66 77
> tx 0x00 0x11 0x22 0x33 0x44 0x55 0x66 0x77 -C
I (6580547) i154cmd: tx sfd done, Radio state: 4
I (6580547) i154cmd: Tx Done 8 bytes
I (6580547) i154cmd: 00 11 22 33 44 55 66 77
tx -l <len>
Transmit IEEE 802154 MAC frame wich has a length=<len>.
- -C: Set cca trigging tx mode true.
> tx -l 10
I (6721867) i154cmd: tx sfd done, Radio state: 4
I (6721867) i154cmd: Tx Done 10 bytes
I (6721867) i154cmd: 00 01 02 03 04 05 06 07
I (6721867) i154cmd: 08 09 00 00 00 00 00 00
> tx -l 10 -C
I (6726067) i154cmd: tx sfd done, Radio state: 4
I (6726067) i154cmd: Tx Done 10 bytes
I (6726067) i154cmd: 00 01 02 03 04 05 06 07
I (6726067) i154cmd: 08 09 00 00 00 00 00 00
txpower
txpower -g
Get the txpower.
> txpower -g
I (7100077) i154cmd: current txpower: 20
txpower -s <n>
Set the txpower.
> txpower -s 40
I (7116217) i154cmd: set txpower: 40
version
Get version of chip and SDK.
> version
IDF Version:v5.3-dev-699-gb94f6ef680-dirty
Chip info:
model:ESP32-H2
cores:1
feature:/BLE/External-Flash:2 MB
revision number:1
help
Get the summary of all registered commands.
> help
cca [-g] [-v <threshold>] [-m <mode>]
cca config
-v, --value=<threshold> cca threshold setting
-m, --mode=<mode> cca mode, 0: carrier; 1: ED; 2: carrier or ED; 3: carrier and ED
-g, --get get the cca cfg
channel [-g] [-s <n>]
get/set the channel number
-g, --get get channel number
-s, --set=<n> set channel number
coordinator [-edg]
enable/disable/get the coordinator
-e, --enable enable the coordinator
-d, --disable disable the coordinator
-g, --get get the coordinator
ed [-d <duration>]
configure the duration
-d, --duration=<duration> configure the duration of energy detection
esp154 [-ed]
enable/disable initialize the IEEE 802.15.4 subsystem
-e, --enable initialize the IEEE 802.15.4 subsystem
-d, --disable deinitialize the IEEE 802.15.4 subsystem
extaddr [-g] [<extaddr>]...
set/get the device extended address
-g, --get get the device extended address
<extaddr> set the device extended address
free
Get the current size of free heap memory
heap
Get minimum size of free heap memory that was available during program
execution
help [<string>]
Print the summary of all registered commands if no arguments are given,
otherwise print summary of given command.
<string> Name of command
log_level <tag|*> <none|error|warn|debug|verbose>
Set log level for all tags or a specific tag.
<tag|*> Log tag to set the level for, or * to set for all tags
<none|error|warn|debug|verbose> Log level to set. Abbreviated words are accepted.
panid [-g] [<panid>]
get/set the device Pan ID
<panid> set the device Pan ID
-g, --get get the device Pan ID
pending [-gr] [-m <mode>] [<addr>]... [-d <addr>]...
configure the pending address table
-m, --mode=<mode> set the autopending mode (0: disable; 1: enable; 2: enhanced)
-g, --get get the autopending mode (0: disable; 1: enable; 2: enhanced)
-r, --reset reset the pending address table
<addr> add the address to pending table (2 bytes for short address, 8 bytes for extended address)
-d, --delete=<addr> delete the address from pending table (2 bytes for short address, 8 bytes for extended address)
promisc [-edg]
enable/disable/get the promiscuous mode
-e, --enable enable the promiscuous mode
-d, --disable disable the promiscuous mode
-g, --get get the promiscuous mode
reg [-r <address>] [-w <address>] [-v <value>]
read/write the register
-r, --read=<address> read the register value
-w, --write=<address> register address to be written
-v, --value=<value> register value to be written
restart
Software reset of the chip
rx [-r <mode>]
enable/disable the receive mode
-r, --receive=<mode> configure the radio receive mode, 0: disable; 1: enable
shortaddr [-g] [<shortaddr>]
get/set the device short address
<shortaddr> set the device short address
-g, --get get the device short address
tx [-C] [-l <len>] [<n>]... [-o <offset>]
transmit IEEE 802154 MAC frame
-l, --length=<len> frame length
-C, --cca_enable set cca trigging tx mode true
<n> transmit raw frame
-o, --offset=<offset> tx buffer offset
txpower [-g] [-s <n>]
get/set the txpower
-g, --get get txpower
-s, --set=<n> set txpower,value range -80dBm~-10dBm
version
Get version of chip and SDK
help <command>
Get the summary of given command.
> help tx
tx [-C] [-l <len>] [<n>]... [-o <offset>]
transmit IEEE 802154 MAC frame
-l, --length=<len> frame length
-C, --cca_enable set cca trigging tx mode true
<n> transmit raw frame
-o, --offset=<offset> tx buffer offset