mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
81 lines
2.7 KiB
Markdown
81 lines
2.7 KiB
Markdown
# _RMT NEC_TX_RX Example_
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This example uses the remote control (RMT) peripheral to transmit and receive codes for the NEC infrared remote protocol.
|
|
|
|
## How to Use Example
|
|
|
|
### Hardware Required
|
|
|
|
* A development board with ESP32 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
|
|
* A USB cable for Power supply and programming
|
|
|
|
By default, this example runs a self test which assumes the TX pin (GPIO18) and RX pin (GPIO19) are _connected together_.
|
|
|
|
To disable self-test mode, comment out RMT_RX_SELF_TEST in infrared_nec_main.c, after which, you need to connect a IR transmitter and a receiver to GPIO18 and GPIO19.
|
|
|
|
The TX pin and RX pin can be modified in top of the main/infrared_nec_main.c file.
|
|
|
|
```
|
|
#define RMT_TX_GPIO_NUM 18 /*!< GPIO number for transmitter signal */
|
|
#define RMT_RX_GPIO_NUM 19 /*!< GPIO number for receiver */
|
|
```
|
|
|
|
### Configure the Project
|
|
|
|
```
|
|
make menuconfig
|
|
```
|
|
|
|
* Set serial port under Serial Flasher Options.
|
|
|
|
### Build and Flash
|
|
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```
|
|
make -j4 flash monitor
|
|
```
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
Run this example, you will see the following output log:
|
|
```
|
|
NEC: RMT TX DATA
|
|
NEC: RMT RCV --- addr: 0xee11 cmd: 0xff00
|
|
NEC: RMT RCV --- addr: 0xed12 cmd: 0xfe01
|
|
NEC: RMT RCV --- addr: 0xec13 cmd: 0xfd02
|
|
NEC: RMT RCV --- addr: 0xeb14 cmd: 0xfc03
|
|
NEC: RMT RCV --- addr: 0xea15 cmd: 0xfb04
|
|
NEC: RMT RCV --- addr: 0xe916 cmd: 0xfa05
|
|
NEC: RMT RCV --- addr: 0xe817 cmd: 0xf906
|
|
NEC: RMT RCV --- addr: 0xe718 cmd: 0xf807
|
|
NEC: RMT RCV --- addr: 0xe619 cmd: 0xf708
|
|
NEC: RMT RCV --- addr: 0xe51a cmd: 0xf609
|
|
NEC: RMT RCV --- addr: 0xe41b cmd: 0xf50a
|
|
NEC: RMT RCV --- addr: 0xe31c cmd: 0xf40b
|
|
NEC: RMT RCV --- addr: 0xe21d cmd: 0xf30c
|
|
NEC: RMT RCV --- addr: 0xe11e cmd: 0xf20d
|
|
NEC: RMT RCV --- addr: 0xe01f cmd: 0xf10e
|
|
NEC: RMT RCV --- addr: 0xdf20 cmd: 0xf00f
|
|
NEC: RMT RCV --- addr: 0xde21 cmd: 0xef10
|
|
NEC: RMT RCV --- addr: 0xdd22 cmd: 0xee11
|
|
NEC: RMT RCV --- addr: 0xdc23 cmd: 0xed12
|
|
NEC: RMT RCV --- addr: 0xdb24 cmd: 0xec13
|
|
NEC: RMT RCV --- addr: 0xda25 cmd: 0xeb14
|
|
```
|
|
|
|
## Troubleshooting
|
|
|
|
* Programming fail
|
|
|
|
* Hardware connection is not correct: run `idf.py monitor`, and reboot your board to see if there is any output logs.
|
|
* The baud rate for downloading is too high: lower your baud rate in the `menuconfig` menu, and try again.
|
|
|
|
For any technical queries, please open an [issue] (https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|