esp-idf/README.md at 8143832041fdf53ab25cffdfc96119213ae75ee7

mirror of https://github.com/espressif/esp-idf.git synced 2024-09-21 06:56:11 -04:00

bizhuangyang 8143832041 spi_master:support octal mode for esp32s2 and esp32s3

Add support for 8-line spi for lcd on esp32s2 and esp32s3

Closes https://github.com/espressif/esp-idf/issues/6371

2021-08-19 16:40:22 +08:00

3.7 KiB

Raw Blame History

LCD tjpgd example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

Overview

This example shows how to decode a jpeg image and display it on an SPI-interfaced LCD, and rotates the image periodically.

Due to the fact that ESP32S2 and ESP32C3 don't have enough memory to hold the decoded image, the graphic shown on the LCD is calculated randomly and has nothing to do with the picture in the example project.

If you want to adapt this example to another type of display or pinout, check lcd_tjpgd_example_main.c for comments with some implementation details.

How to Use Example

Hardware Required

An ESP development board
An SPI-interfaced LCD
An USB cable for power supply and programming

Hardware Connection

If using default settings, the hardware connection can be as below:

        Board                               LCD Screen
      +--------+              +---------------------------------+
      |        |              |                                 |
      |    3V3 +--------------+ VCC   +----------------------+  |
      |        |              |       |                      |  |
      |    GND +--------------+ GND   |                      |  |
      |        |              |       |                      |  |
      |     23 +--------------+ MOSI  |                      |  |
      |        |              |       |                      |  |
      |     19 +--------------+ SCK   |                      |  |
      |        |              |       |                      |  |
      |     22 +--------------+ CS    |                      |  |
      |        |              |       |                      |  |
      |     21 +--------------+ DC    |                      |  |
      |        |              |       |                      |  |
      |     18 +--------------+ RST   |                      |  |
      |        |              |       |                      |  |
      |      5 +--------------+ BCKL  +----------------------+  |
      |        |              |                                 |
      +--------+              +---------------------------------+

If not using default settings, the interface GPIOs should be set by macros in lcd_tjpgd_example_main.c, where:

GPIO number	LCD pin
PIN_NUM_CLK	SCK
PIN_NUM_CS	CS
PIN_NUM_DC	DC
PIN_NUM_RST	RST
PIN_NUM_BCKL	LED
PIN_NUM_MOSI	MOSI

8-line LCD Usage

Firstly, please run idf.py menuconfig and set the Drive a LCD with 8 data lines option at Example Configuration.

Check if the pins below are correctly connected as the settings by macros in lcd_tjpgd_example_main.c, where:

GPIO number	LCD pin
PIN_NUM_CLK	SCK
PIN_NUM_CS	CS
PIN_NUM_DC	DC
PIN_NUM_RST	RST
PIN_NUM_BCKL	LED
PIN_NUM_MOSI	D0
PIN_NUM_DATA1	D1
PIN_NUM_DATA2	D2
PIN_NUM_DATA3	D3
PIN_NUM_DATA4	D4
PIN_NUM_DATA5	D5
PIN_NUM_DATA6	D6
PIN_NUM_DATA7	D7

Build and Flash

Run idf.py -p PORT flash monitor to build, flash and monitor the project. A flowing picture will be shown on the LCD screen.

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Troubleshooting

For any technical queries, please open an [issue] (https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.

3.7 KiB Raw Blame History