esp-idf/examples/bluetooth/nimble/power_save/README.md

113 lines
4.6 KiB
Markdown

| Supported Targets | ESP32 | ESP32-C3 | ESP32-S3 |
| ----------------- | ----- | -------- | -------- |
Bluetooth Power Save Example
=================================
This example is based on the [bleprph](../bleprph) example to show how to use the bluetooth power save mode.
If the modem sleep mode is enabled, bluetooth will switch periodically between active and sleep.
In sleep state, RF, PHY and BB are turned off in order to reduce power consumption.
This example contains five build configurations. For each configuration, a few configuration options are set:
- `sdkconfig.defaults.esp32`: ESP32 uses 32kHz XTAL as low power clock in light sleep enabled.
- `sdkconfig.40m.esp32c3`: ESP32C3 uses 32kHz XTAL as low power clock in light sleep enabled.
- `sdkconfig.esp32c3_40m`: ESP32C3 uses main XTAL as low power clock in light sleep enabled.
- `sdkconfig.defaults.esp32s3`: ESP32S3 uses 32kHz XTAL as low power clock in light sleep enabled.
- `sdkconfig.40m.esp32s3`: ESP32S3 uses main XTAL as low power clock in light sleep enabled.
## How to use example
### Hardware Required
This example should be able to run on any commonly available ESP32/ESP32-C3/ESP32-S3 development board.
### Configure the project
```
idf.py menuconfig
```
1. Configure RTC clock source:
- `Component config > Hardware Settings > RTC Clock Config > RTC clock source`
2. Enable power management:
- `Component config > Power Management > [*] Support for power management`
3. Configure FreeRTOS:
- `Component config > FreeRTOS > Kernel`
- `(1000) configTICK_RATE_HZ`
- `[*] configUSE_TICKLESS_IDLE`
- `(3) configEXPECTED_IDLE_TIME_BEFORE_SLEEP`
4. Enable power down MAC and baseband:
- `Component config > PHY > [*] Power down MAC and baseband of Wi-Fi and Bluetooth when PHY is disabled`
5. Enable bluetooth modem sleep:
- `Component config > Bluetooth > Controller Options > MODEM SLEEP Options`
- `[*] Bluetooth modem sleep`
- `[*] Bluetooth Modem sleep Mode 1`
6. Configure bluetooth low power clock:
- `Component config > Bluetooth > Controller Options > MODEM SLEEP Options > Bluetooth modem sleep > Bluetooth Modem sleep Mode 1 > Bluetooth low power clock`
7. Enable power up main XTAL during light sleep:
- `Component config > Bluetooth > Controller Options > MODEM SLEEP Options > [*] power up main XTAL during light sleep`
### Build and Flash
```
idf.py -D SDKCONFIG_DEFAULTS="sdkconfig.defaults;sdkconfig.40m.esp32c3" set-target ESP32C3 build
```
* `-D SDKCONFIG_DEFAULTS` select configuration file to be used for creating app sdkconfig.
* `set-target ` Set the chip target to build.
To flash the project and see the output, run:
```
idf.py -p PORT flash monitor
```
(Replace PORT with the name of the serial port to use.)
(To exit the serial monitor, type ``Ctrl-]``.)
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
## Example Output
When you run this example, the prints the following at the very begining:
```
I (333) cpu_start: Starting scheduler.
I (347) pm: Frequency switching config: CPU_MAX: 160, APB_MAX: 80, APB_MIN: 40, Light sleep: ENABLED
I (351) sleep: Enable automatic switching of GPIO sleep configuration
I (358) BTDM_INIT: BT controller compile version [f2e5d81]
I (365) BTDM_INIT: Bluetooth will use main XTAL as Bluetooth sleep clock.
I (372) phy_init: phy_version 912,d001756,Jun 2 2022,16:28:07
I (411) system_api: Base MAC address is not set
I (412) system_api: read default base MAC address from EFUSE
I (412) BTDM_INIT: Bluetooth MAC: 7c:df:a1:61:b6:f6
I (419) NimBLE_BLE_PRPH: BLE Host Task Started
I (424) uart: queue free spaces: 8
I (432) NimBLE: GAP procedure initiated: stop advertising.
I (435) NimBLE: Device Address:
I (437) NimBLE: 7c:df:a1:61:b6:f6
I (441) NimBLE:
I (446) NimBLE: GAP procedure initiated: advertise;
I (450) NimBLE: disc_mode=2
I (453) NimBLE: adv_channel_map=0 own_addr_type=0 adv_filter_policy=0 adv_itvl_min=0 adv_itvl_max=0
I (463) NimBLE:
```
## Typical current consumption with management enabled
| | max current | modem sleep | light sleep (main XTAL)| light sleep (32KHz XTAL)|
|-------- | ----------- | ------------ | ---------------------- |------------------------ |
| ESP32 | 231 mA | 14.1 mA | X | 1.9 mA |
| ESP32C3 | 262 mA | 12 mA | 2.3 mA | 140 uA |
| ESP32S3 | 240 mA | 17.9 mA | 3.3 mA | 230 uA |
X: This feature is currently not supported.
## Example Breakdown
- ESP32 does not support the use of main XTAL in light sleep mode, so an external 32kHz crystal is required.