mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
70 lines
2.7 KiB
Markdown
70 lines
2.7 KiB
Markdown
| Supported Targets | ESP32 | ESP32-C6 | ESP32-S3 |
|
|
| ----------------- | ----- | -------- | -------- |
|
|
# MCPWM RC Servo Control Example
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This example illustrates how to drive a typical [RC Servo](https://en.wikipedia.org/wiki/Servo_%28radio_control%29) by sending a PWM signal using the MCPWM driver. The PWM pulse has a frequency of 50Hz (period of 20ms), and the active-high time (which controls the rotation) ranges from 0.5s to 2.5ms with 1.5ms always being center of range.
|
|
|
|
## How to Use Example
|
|
|
|
### Hardware Required
|
|
|
|
* A development board with any Espressif SoC which features MCPWM peripheral (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
|
|
* A USB cable for Power supply and programming
|
|
* A RC servo motor, e.g. [SG90](http://www.ee.ic.ac.uk/pcheung/teaching/DE1_EE/stores/sg90_datasheet.pdf)
|
|
|
|
Connection :
|
|
|
|
```
|
|
ESP Board Servo Motor 5V
|
|
+-------------------+ +---------------+ ^
|
|
| SERVO_PULSE_GPIO +-----+PWM VCC +----+
|
|
| | | |
|
|
| GND +-----+GND |
|
|
+-------------------+ +---------------+
|
|
```
|
|
|
|
Note that, some kind of servo might need a higher current supply than the development board usually can provide. It's recommended to power the servo separately.
|
|
|
|
### Build and Flash
|
|
|
|
Run `idf.py -p PORT flash monitor` to build, flash and monitor the project.
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
|
|
## Example Output
|
|
|
|
Run the example, you will see the following output log:
|
|
|
|
```
|
|
...
|
|
I (0) cpu_start: Starting scheduler on APP CPU.
|
|
I (305) example: Create timer and operator
|
|
I (305) example: Connect timer and operator
|
|
I (305) example: Create comparator and generator from the operator
|
|
I (315) gpio: GPIO[44]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
|
|
I (325) example: Set generator action on timer and compare event
|
|
I (335) example: Enable and start timer
|
|
I (335) example: Angle of rotation: 0
|
|
I (1345) example: Angle of rotation: 2
|
|
I (2345) example: Angle of rotation: 4
|
|
I (3345) example: Angle of rotation: 6
|
|
I (4345) example: Angle of rotation: 8
|
|
I (5345) example: Angle of rotation: 10
|
|
I (6345) example: Angle of rotation: 12
|
|
I (7345) example: Angle of rotation: 14
|
|
I (8345) example: Angle of rotation: 16
|
|
I (9345) example: Angle of rotation: 18
|
|
...
|
|
```
|
|
|
|
The servo will rotate from -90 degree to 90 degree, and then turn back again.
|
|
|
|
## Troubleshooting
|
|
|
|
For any technical queries, please open an [issue] (https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|