mirror of
https://github.com/espressif/esp-idf.git
synced 2024-09-20 20:56:01 -04:00
1451 lines
63 KiB
C
1451 lines
63 KiB
C
/**
|
|
* SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
#pragma once
|
|
|
|
#include <stdint.h>
|
|
#include "soc/soc.h"
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
/** I2C_SCL_LOW_PERIOD_REG register
|
|
* Configures the low level width of the SCL
|
|
* Clock
|
|
*/
|
|
#define I2C_SCL_LOW_PERIOD_REG(i) (REG_I2C_BASE(i) + 0x0)
|
|
/** I2C_SCL_LOW_PERIOD : R/W; bitpos: [8:0]; default: 0;
|
|
* This register is used to configure for how long SCL remains low in master mode, in
|
|
* I2C module clock cycles.
|
|
*/
|
|
#define I2C_SCL_LOW_PERIOD 0x000001FFU
|
|
#define I2C_SCL_LOW_PERIOD_M (I2C_SCL_LOW_PERIOD_V << I2C_SCL_LOW_PERIOD_S)
|
|
#define I2C_SCL_LOW_PERIOD_V 0x000001FFU
|
|
#define I2C_SCL_LOW_PERIOD_S 0
|
|
|
|
/** I2C_CTR_REG register
|
|
* Transmission setting
|
|
*/
|
|
#define I2C_CTR_REG(i) (REG_I2C_BASE(i) + 0x4)
|
|
/** I2C_SDA_FORCE_OUT : R/W; bitpos: [0]; default: 0;
|
|
* 1: direct output, 0: open drain output.
|
|
*/
|
|
#define I2C_SDA_FORCE_OUT (BIT(0))
|
|
#define I2C_SDA_FORCE_OUT_M (I2C_SDA_FORCE_OUT_V << I2C_SDA_FORCE_OUT_S)
|
|
#define I2C_SDA_FORCE_OUT_V 0x00000001U
|
|
#define I2C_SDA_FORCE_OUT_S 0
|
|
/** I2C_SCL_FORCE_OUT : R/W; bitpos: [1]; default: 0;
|
|
* 1: direct output, 0: open drain output.
|
|
*/
|
|
#define I2C_SCL_FORCE_OUT (BIT(1))
|
|
#define I2C_SCL_FORCE_OUT_M (I2C_SCL_FORCE_OUT_V << I2C_SCL_FORCE_OUT_S)
|
|
#define I2C_SCL_FORCE_OUT_V 0x00000001U
|
|
#define I2C_SCL_FORCE_OUT_S 1
|
|
/** I2C_SAMPLE_SCL_LEVEL : R/W; bitpos: [2]; default: 0;
|
|
* This register is used to select the sample mode.
|
|
* 1: sample SDA data on the SCL low level.
|
|
* 0: sample SDA data on the SCL high level.
|
|
*/
|
|
#define I2C_SAMPLE_SCL_LEVEL (BIT(2))
|
|
#define I2C_SAMPLE_SCL_LEVEL_M (I2C_SAMPLE_SCL_LEVEL_V << I2C_SAMPLE_SCL_LEVEL_S)
|
|
#define I2C_SAMPLE_SCL_LEVEL_V 0x00000001U
|
|
#define I2C_SAMPLE_SCL_LEVEL_S 2
|
|
/** I2C_RX_FULL_ACK_LEVEL : R/W; bitpos: [3]; default: 1;
|
|
* This register is used to configure the ACK value that need to sent by master when
|
|
* the rx_fifo_cnt has reached the threshold.
|
|
*/
|
|
#define I2C_RX_FULL_ACK_LEVEL (BIT(3))
|
|
#define I2C_RX_FULL_ACK_LEVEL_M (I2C_RX_FULL_ACK_LEVEL_V << I2C_RX_FULL_ACK_LEVEL_S)
|
|
#define I2C_RX_FULL_ACK_LEVEL_V 0x00000001U
|
|
#define I2C_RX_FULL_ACK_LEVEL_S 3
|
|
/** I2C_MS_MODE : R/W; bitpos: [4]; default: 0;
|
|
* Set this bit to configure the module as an I2C Master. Clear this bit to configure
|
|
* the
|
|
* module as an I2C Slave.
|
|
*/
|
|
#define I2C_MS_MODE (BIT(4))
|
|
#define I2C_MS_MODE_M (I2C_MS_MODE_V << I2C_MS_MODE_S)
|
|
#define I2C_MS_MODE_V 0x00000001U
|
|
#define I2C_MS_MODE_S 4
|
|
/** I2C_TRANS_START : WT; bitpos: [5]; default: 0;
|
|
* Set this bit to start sending the data in txfifo.
|
|
*/
|
|
#define I2C_TRANS_START (BIT(5))
|
|
#define I2C_TRANS_START_M (I2C_TRANS_START_V << I2C_TRANS_START_S)
|
|
#define I2C_TRANS_START_V 0x00000001U
|
|
#define I2C_TRANS_START_S 5
|
|
/** I2C_TX_LSB_FIRST : R/W; bitpos: [6]; default: 0;
|
|
* This bit is used to control the sending mode for data needing to be sent.
|
|
* 1: send data from the least significant bit,
|
|
* 0: send data from the most significant bit.
|
|
*/
|
|
#define I2C_TX_LSB_FIRST (BIT(6))
|
|
#define I2C_TX_LSB_FIRST_M (I2C_TX_LSB_FIRST_V << I2C_TX_LSB_FIRST_S)
|
|
#define I2C_TX_LSB_FIRST_V 0x00000001U
|
|
#define I2C_TX_LSB_FIRST_S 6
|
|
/** I2C_RX_LSB_FIRST : R/W; bitpos: [7]; default: 0;
|
|
* This bit is used to control the storage mode for received data.
|
|
* 1: receive data from the least significant bit,
|
|
* 0: receive data from the most significant bit.
|
|
*/
|
|
#define I2C_RX_LSB_FIRST (BIT(7))
|
|
#define I2C_RX_LSB_FIRST_M (I2C_RX_LSB_FIRST_V << I2C_RX_LSB_FIRST_S)
|
|
#define I2C_RX_LSB_FIRST_V 0x00000001U
|
|
#define I2C_RX_LSB_FIRST_S 7
|
|
/** I2C_CLK_EN : R/W; bitpos: [8]; default: 0;
|
|
* Reserved
|
|
*/
|
|
#define I2C_CLK_EN (BIT(8))
|
|
#define I2C_CLK_EN_M (I2C_CLK_EN_V << I2C_CLK_EN_S)
|
|
#define I2C_CLK_EN_V 0x00000001U
|
|
#define I2C_CLK_EN_S 8
|
|
/** I2C_ARBITRATION_EN : R/W; bitpos: [9]; default: 1;
|
|
* This is the enable bit for arbitration_lost.
|
|
*/
|
|
#define I2C_ARBITRATION_EN (BIT(9))
|
|
#define I2C_ARBITRATION_EN_M (I2C_ARBITRATION_EN_V << I2C_ARBITRATION_EN_S)
|
|
#define I2C_ARBITRATION_EN_V 0x00000001U
|
|
#define I2C_ARBITRATION_EN_S 9
|
|
/** I2C_FSM_RST : WT; bitpos: [10]; default: 0;
|
|
* This register is used to reset the scl FMS.
|
|
*/
|
|
#define I2C_FSM_RST (BIT(10))
|
|
#define I2C_FSM_RST_M (I2C_FSM_RST_V << I2C_FSM_RST_S)
|
|
#define I2C_FSM_RST_V 0x00000001U
|
|
#define I2C_FSM_RST_S 10
|
|
/** I2C_CONF_UPGATE : WT; bitpos: [11]; default: 0;
|
|
* synchronization bit
|
|
*/
|
|
#define I2C_CONF_UPGATE (BIT(11))
|
|
#define I2C_CONF_UPGATE_M (I2C_CONF_UPGATE_V << I2C_CONF_UPGATE_S)
|
|
#define I2C_CONF_UPGATE_V 0x00000001U
|
|
#define I2C_CONF_UPGATE_S 11
|
|
/** I2C_SLV_TX_AUTO_START_EN : R/W; bitpos: [12]; default: 0;
|
|
* This is the enable bit for slave to send data automatically
|
|
*/
|
|
#define I2C_SLV_TX_AUTO_START_EN (BIT(12))
|
|
#define I2C_SLV_TX_AUTO_START_EN_M (I2C_SLV_TX_AUTO_START_EN_V << I2C_SLV_TX_AUTO_START_EN_S)
|
|
#define I2C_SLV_TX_AUTO_START_EN_V 0x00000001U
|
|
#define I2C_SLV_TX_AUTO_START_EN_S 12
|
|
/** I2C_ADDR_10BIT_RW_CHECK_EN : R/W; bitpos: [13]; default: 0;
|
|
* This is the enable bit to check if the r/w bit of 10bit addressing consists with
|
|
* I2C protocol
|
|
*/
|
|
#define I2C_ADDR_10BIT_RW_CHECK_EN (BIT(13))
|
|
#define I2C_ADDR_10BIT_RW_CHECK_EN_M (I2C_ADDR_10BIT_RW_CHECK_EN_V << I2C_ADDR_10BIT_RW_CHECK_EN_S)
|
|
#define I2C_ADDR_10BIT_RW_CHECK_EN_V 0x00000001U
|
|
#define I2C_ADDR_10BIT_RW_CHECK_EN_S 13
|
|
/** I2C_ADDR_BROADCASTING_EN : R/W; bitpos: [14]; default: 0;
|
|
* This is the enable bit to support the 7bit general call function.
|
|
*/
|
|
#define I2C_ADDR_BROADCASTING_EN (BIT(14))
|
|
#define I2C_ADDR_BROADCASTING_EN_M (I2C_ADDR_BROADCASTING_EN_V << I2C_ADDR_BROADCASTING_EN_S)
|
|
#define I2C_ADDR_BROADCASTING_EN_V 0x00000001U
|
|
#define I2C_ADDR_BROADCASTING_EN_S 14
|
|
|
|
/** I2C_SR_REG register
|
|
* Describe I2C work status.
|
|
*/
|
|
#define I2C_SR_REG(i) (REG_I2C_BASE(i) + 0x8)
|
|
/** I2C_RESP_REC : RO; bitpos: [0]; default: 0;
|
|
* The received ACK value in master mode or slave mode. 0: ACK, 1: NACK.
|
|
*/
|
|
#define I2C_RESP_REC (BIT(0))
|
|
#define I2C_RESP_REC_M (I2C_RESP_REC_V << I2C_RESP_REC_S)
|
|
#define I2C_RESP_REC_V 0x00000001U
|
|
#define I2C_RESP_REC_S 0
|
|
/** I2C_SLAVE_RW : RO; bitpos: [1]; default: 0;
|
|
* When in slave mode, 1: master reads from slave, 0: master writes to slave.
|
|
*/
|
|
#define I2C_SLAVE_RW (BIT(1))
|
|
#define I2C_SLAVE_RW_M (I2C_SLAVE_RW_V << I2C_SLAVE_RW_S)
|
|
#define I2C_SLAVE_RW_V 0x00000001U
|
|
#define I2C_SLAVE_RW_S 1
|
|
/** I2C_ARB_LOST : RO; bitpos: [3]; default: 0;
|
|
* When the I2C controller loses control of SCL line, this register changes to 1.
|
|
*/
|
|
#define I2C_ARB_LOST (BIT(3))
|
|
#define I2C_ARB_LOST_M (I2C_ARB_LOST_V << I2C_ARB_LOST_S)
|
|
#define I2C_ARB_LOST_V 0x00000001U
|
|
#define I2C_ARB_LOST_S 3
|
|
/** I2C_BUS_BUSY : RO; bitpos: [4]; default: 0;
|
|
* 1: the I2C bus is busy transferring data, 0: the I2C bus is in idle state.
|
|
*/
|
|
#define I2C_BUS_BUSY (BIT(4))
|
|
#define I2C_BUS_BUSY_M (I2C_BUS_BUSY_V << I2C_BUS_BUSY_S)
|
|
#define I2C_BUS_BUSY_V 0x00000001U
|
|
#define I2C_BUS_BUSY_S 4
|
|
/** I2C_SLAVE_ADDRESSED : RO; bitpos: [5]; default: 0;
|
|
* When configured as an I2C Slave, and the address sent by the master is
|
|
* equal to the address of the slave, then this bit will be of high level.
|
|
*/
|
|
#define I2C_SLAVE_ADDRESSED (BIT(5))
|
|
#define I2C_SLAVE_ADDRESSED_M (I2C_SLAVE_ADDRESSED_V << I2C_SLAVE_ADDRESSED_S)
|
|
#define I2C_SLAVE_ADDRESSED_V 0x00000001U
|
|
#define I2C_SLAVE_ADDRESSED_S 5
|
|
/** I2C_RXFIFO_CNT : RO; bitpos: [13:8]; default: 0;
|
|
* This field represents the amount of data needed to be sent.
|
|
*/
|
|
#define I2C_RXFIFO_CNT 0x0000003FU
|
|
#define I2C_RXFIFO_CNT_M (I2C_RXFIFO_CNT_V << I2C_RXFIFO_CNT_S)
|
|
#define I2C_RXFIFO_CNT_V 0x0000003FU
|
|
#define I2C_RXFIFO_CNT_S 8
|
|
/** I2C_STRETCH_CAUSE : RO; bitpos: [15:14]; default: 3;
|
|
* The cause of stretching SCL low in slave mode. 0: stretching SCL low at the
|
|
* beginning of I2C read data state. 1: stretching SCL low when I2C Tx FIFO is empty
|
|
* in slave mode. 2: stretching SCL low when I2C Rx FIFO is full in slave mode.
|
|
*/
|
|
#define I2C_STRETCH_CAUSE 0x00000003U
|
|
#define I2C_STRETCH_CAUSE_M (I2C_STRETCH_CAUSE_V << I2C_STRETCH_CAUSE_S)
|
|
#define I2C_STRETCH_CAUSE_V 0x00000003U
|
|
#define I2C_STRETCH_CAUSE_S 14
|
|
/** I2C_TXFIFO_CNT : RO; bitpos: [23:18]; default: 0;
|
|
* This field stores the amount of received data in RAM.
|
|
*/
|
|
#define I2C_TXFIFO_CNT 0x0000003FU
|
|
#define I2C_TXFIFO_CNT_M (I2C_TXFIFO_CNT_V << I2C_TXFIFO_CNT_S)
|
|
#define I2C_TXFIFO_CNT_V 0x0000003FU
|
|
#define I2C_TXFIFO_CNT_S 18
|
|
/** I2C_SCL_MAIN_STATE_LAST : RO; bitpos: [26:24]; default: 0;
|
|
* This field indicates the states of the I2C module state machine.
|
|
* 0: Idle, 1: Address shift, 2: ACK address, 3: Rx data, 4: Tx data, 5: Send ACK, 6:
|
|
* Wait ACK
|
|
*/
|
|
#define I2C_SCL_MAIN_STATE_LAST 0x00000007U
|
|
#define I2C_SCL_MAIN_STATE_LAST_M (I2C_SCL_MAIN_STATE_LAST_V << I2C_SCL_MAIN_STATE_LAST_S)
|
|
#define I2C_SCL_MAIN_STATE_LAST_V 0x00000007U
|
|
#define I2C_SCL_MAIN_STATE_LAST_S 24
|
|
/** I2C_SCL_STATE_LAST : RO; bitpos: [30:28]; default: 0;
|
|
* This field indicates the states of the state machine used to produce SCL.
|
|
* 0: Idle, 1: Start, 2: Negative edge, 3: Low, 4: Positive edge, 5: High, 6: Stop
|
|
*/
|
|
#define I2C_SCL_STATE_LAST 0x00000007U
|
|
#define I2C_SCL_STATE_LAST_M (I2C_SCL_STATE_LAST_V << I2C_SCL_STATE_LAST_S)
|
|
#define I2C_SCL_STATE_LAST_V 0x00000007U
|
|
#define I2C_SCL_STATE_LAST_S 28
|
|
|
|
/** I2C_TO_REG register
|
|
* Setting time out control for receiving data.
|
|
*/
|
|
#define I2C_TO_REG(i) (REG_I2C_BASE(i) + 0xc)
|
|
/** I2C_TIME_OUT_VALUE : R/W; bitpos: [4:0]; default: 16;
|
|
* This register is used to configure the timeout for receiving a data bit in APB
|
|
* clock cycles.
|
|
*/
|
|
#define I2C_TIME_OUT_VALUE 0x0000001FU
|
|
#define I2C_TIME_OUT_VALUE_M (I2C_TIME_OUT_VALUE_V << I2C_TIME_OUT_VALUE_S)
|
|
#define I2C_TIME_OUT_VALUE_V 0x0000001FU
|
|
#define I2C_TIME_OUT_VALUE_S 0
|
|
/** I2C_TIME_OUT_EN : R/W; bitpos: [5]; default: 0;
|
|
* This is the enable bit for time out control.
|
|
*/
|
|
#define I2C_TIME_OUT_EN (BIT(5))
|
|
#define I2C_TIME_OUT_EN_M (I2C_TIME_OUT_EN_V << I2C_TIME_OUT_EN_S)
|
|
#define I2C_TIME_OUT_EN_V 0x00000001U
|
|
#define I2C_TIME_OUT_EN_S 5
|
|
|
|
/** I2C_SLAVE_ADDR_REG register
|
|
* Local slave address setting
|
|
*/
|
|
#define I2C_SLAVE_ADDR_REG(i) (REG_I2C_BASE(i) + 0x10)
|
|
/** I2C_SLAVE_ADDR : R/W; bitpos: [14:0]; default: 0;
|
|
* When configured as an I2C Slave, this field is used to configure the slave address.
|
|
*/
|
|
#define I2C_SLAVE_ADDR 0x00007FFFU
|
|
#define I2C_SLAVE_ADDR_M (I2C_SLAVE_ADDR_V << I2C_SLAVE_ADDR_S)
|
|
#define I2C_SLAVE_ADDR_V 0x00007FFFU
|
|
#define I2C_SLAVE_ADDR_S 0
|
|
/** I2C_ADDR_10BIT_EN : R/W; bitpos: [31]; default: 0;
|
|
* This field is used to enable the slave 10-bit addressing mode in master mode.
|
|
*/
|
|
#define I2C_ADDR_10BIT_EN (BIT(31))
|
|
#define I2C_ADDR_10BIT_EN_M (I2C_ADDR_10BIT_EN_V << I2C_ADDR_10BIT_EN_S)
|
|
#define I2C_ADDR_10BIT_EN_V 0x00000001U
|
|
#define I2C_ADDR_10BIT_EN_S 31
|
|
|
|
/** I2C_FIFO_ST_REG register
|
|
* FIFO status register.
|
|
*/
|
|
#define I2C_FIFO_ST_REG(i) (REG_I2C_BASE(i) + 0x14)
|
|
/** I2C_RXFIFO_RADDR : RO; bitpos: [4:0]; default: 0;
|
|
* This is the offset address of the APB reading from rxfifo
|
|
*/
|
|
#define I2C_RXFIFO_RADDR 0x0000001FU
|
|
#define I2C_RXFIFO_RADDR_M (I2C_RXFIFO_RADDR_V << I2C_RXFIFO_RADDR_S)
|
|
#define I2C_RXFIFO_RADDR_V 0x0000001FU
|
|
#define I2C_RXFIFO_RADDR_S 0
|
|
/** I2C_RXFIFO_WADDR : RO; bitpos: [9:5]; default: 0;
|
|
* This is the offset address of i2c module receiving data and writing to rxfifo.
|
|
*/
|
|
#define I2C_RXFIFO_WADDR 0x0000001FU
|
|
#define I2C_RXFIFO_WADDR_M (I2C_RXFIFO_WADDR_V << I2C_RXFIFO_WADDR_S)
|
|
#define I2C_RXFIFO_WADDR_V 0x0000001FU
|
|
#define I2C_RXFIFO_WADDR_S 5
|
|
/** I2C_TXFIFO_RADDR : RO; bitpos: [14:10]; default: 0;
|
|
* This is the offset address of i2c module reading from txfifo.
|
|
*/
|
|
#define I2C_TXFIFO_RADDR 0x0000001FU
|
|
#define I2C_TXFIFO_RADDR_M (I2C_TXFIFO_RADDR_V << I2C_TXFIFO_RADDR_S)
|
|
#define I2C_TXFIFO_RADDR_V 0x0000001FU
|
|
#define I2C_TXFIFO_RADDR_S 10
|
|
/** I2C_TXFIFO_WADDR : RO; bitpos: [19:15]; default: 0;
|
|
* This is the offset address of APB bus writing to txfifo.
|
|
*/
|
|
#define I2C_TXFIFO_WADDR 0x0000001FU
|
|
#define I2C_TXFIFO_WADDR_M (I2C_TXFIFO_WADDR_V << I2C_TXFIFO_WADDR_S)
|
|
#define I2C_TXFIFO_WADDR_V 0x0000001FU
|
|
#define I2C_TXFIFO_WADDR_S 15
|
|
/** I2C_SLAVE_RW_POINT : RO; bitpos: [29:22]; default: 0;
|
|
* The received data in I2C slave mode.
|
|
*/
|
|
#define I2C_SLAVE_RW_POINT 0x000000FFU
|
|
#define I2C_SLAVE_RW_POINT_M (I2C_SLAVE_RW_POINT_V << I2C_SLAVE_RW_POINT_S)
|
|
#define I2C_SLAVE_RW_POINT_V 0x000000FFU
|
|
#define I2C_SLAVE_RW_POINT_S 22
|
|
|
|
/** I2C_FIFO_CONF_REG register
|
|
* FIFO configuration register.
|
|
*/
|
|
#define I2C_FIFO_CONF_REG(i) (REG_I2C_BASE(i) + 0x18)
|
|
/** I2C_RXFIFO_WM_THRHD : R/W; bitpos: [4:0]; default: 11;
|
|
* The water mark threshold of rx FIFO in nonfifo access mode. When
|
|
* reg_reg_fifo_prt_en is 1 and rx FIFO counter is bigger than
|
|
* reg_rxfifo_wm_thrhd[4:0], reg_rxfifo_wm_int_raw bit will be valid.
|
|
*/
|
|
#define I2C_RXFIFO_WM_THRHD 0x0000001FU
|
|
#define I2C_RXFIFO_WM_THRHD_M (I2C_RXFIFO_WM_THRHD_V << I2C_RXFIFO_WM_THRHD_S)
|
|
#define I2C_RXFIFO_WM_THRHD_V 0x0000001FU
|
|
#define I2C_RXFIFO_WM_THRHD_S 0
|
|
/** I2C_TXFIFO_WM_THRHD : R/W; bitpos: [9:5]; default: 4;
|
|
* The water mark threshold of tx FIFO in nonfifo access mode. When
|
|
* reg_reg_fifo_prt_en is 1 and tx FIFO counter is smaller than
|
|
* reg_txfifo_wm_thrhd[4:0], reg_txfifo_wm_int_raw bit will be valid.
|
|
*/
|
|
#define I2C_TXFIFO_WM_THRHD 0x0000001FU
|
|
#define I2C_TXFIFO_WM_THRHD_M (I2C_TXFIFO_WM_THRHD_V << I2C_TXFIFO_WM_THRHD_S)
|
|
#define I2C_TXFIFO_WM_THRHD_V 0x0000001FU
|
|
#define I2C_TXFIFO_WM_THRHD_S 5
|
|
/** I2C_NONFIFO_EN : R/W; bitpos: [10]; default: 0;
|
|
* Set this bit to enable APB nonfifo access.
|
|
*/
|
|
#define I2C_NONFIFO_EN (BIT(10))
|
|
#define I2C_NONFIFO_EN_M (I2C_NONFIFO_EN_V << I2C_NONFIFO_EN_S)
|
|
#define I2C_NONFIFO_EN_V 0x00000001U
|
|
#define I2C_NONFIFO_EN_S 10
|
|
/** I2C_FIFO_ADDR_CFG_EN : R/W; bitpos: [11]; default: 0;
|
|
* When this bit is set to 1, the byte received after the I2C address byte represents
|
|
* the offset address in the I2C Slave RAM.
|
|
*/
|
|
#define I2C_FIFO_ADDR_CFG_EN (BIT(11))
|
|
#define I2C_FIFO_ADDR_CFG_EN_M (I2C_FIFO_ADDR_CFG_EN_V << I2C_FIFO_ADDR_CFG_EN_S)
|
|
#define I2C_FIFO_ADDR_CFG_EN_V 0x00000001U
|
|
#define I2C_FIFO_ADDR_CFG_EN_S 11
|
|
/** I2C_RX_FIFO_RST : R/W; bitpos: [12]; default: 0;
|
|
* Set this bit to reset rx-fifo.
|
|
*/
|
|
#define I2C_RX_FIFO_RST (BIT(12))
|
|
#define I2C_RX_FIFO_RST_M (I2C_RX_FIFO_RST_V << I2C_RX_FIFO_RST_S)
|
|
#define I2C_RX_FIFO_RST_V 0x00000001U
|
|
#define I2C_RX_FIFO_RST_S 12
|
|
/** I2C_TX_FIFO_RST : R/W; bitpos: [13]; default: 0;
|
|
* Set this bit to reset tx-fifo.
|
|
*/
|
|
#define I2C_TX_FIFO_RST (BIT(13))
|
|
#define I2C_TX_FIFO_RST_M (I2C_TX_FIFO_RST_V << I2C_TX_FIFO_RST_S)
|
|
#define I2C_TX_FIFO_RST_V 0x00000001U
|
|
#define I2C_TX_FIFO_RST_S 13
|
|
/** I2C_FIFO_PRT_EN : R/W; bitpos: [14]; default: 1;
|
|
* The control enable bit of FIFO pointer in non-fifo access mode. This bit controls
|
|
* the valid bits and the interrupts of tx/rx_fifo overflow, underflow, full and empty.
|
|
*/
|
|
#define I2C_FIFO_PRT_EN (BIT(14))
|
|
#define I2C_FIFO_PRT_EN_M (I2C_FIFO_PRT_EN_V << I2C_FIFO_PRT_EN_S)
|
|
#define I2C_FIFO_PRT_EN_V 0x00000001U
|
|
#define I2C_FIFO_PRT_EN_S 14
|
|
|
|
/** I2C_DATA_REG register
|
|
* Rx FIFO read data.
|
|
*/
|
|
#define I2C_DATA_REG(i) (REG_I2C_BASE(i) + 0x1c)
|
|
/** I2C_FIFO_RDATA : HRO; bitpos: [7:0]; default: 0;
|
|
* The value of rx FIFO read data.
|
|
*/
|
|
#define I2C_FIFO_RDATA 0x000000FFU
|
|
#define I2C_FIFO_RDATA_M (I2C_FIFO_RDATA_V << I2C_FIFO_RDATA_S)
|
|
#define I2C_FIFO_RDATA_V 0x000000FFU
|
|
#define I2C_FIFO_RDATA_S 0
|
|
|
|
/** I2C_INT_RAW_REG register
|
|
* Raw interrupt status
|
|
*/
|
|
#define I2C_INT_RAW_REG(i) (REG_I2C_BASE(i) + 0x20)
|
|
/** I2C_RXFIFO_WM_INT_RAW : R/SS/WTC; bitpos: [0]; default: 0;
|
|
* The raw interrupt bit for I2C_RXFIFO_WM_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_WM_INT_RAW (BIT(0))
|
|
#define I2C_RXFIFO_WM_INT_RAW_M (I2C_RXFIFO_WM_INT_RAW_V << I2C_RXFIFO_WM_INT_RAW_S)
|
|
#define I2C_RXFIFO_WM_INT_RAW_V 0x00000001U
|
|
#define I2C_RXFIFO_WM_INT_RAW_S 0
|
|
/** I2C_TXFIFO_WM_INT_RAW : R/SS/WTC; bitpos: [1]; default: 1;
|
|
* The raw interrupt bit for I2C_TXFIFO_WM_INT interrupt.
|
|
*/
|
|
#define I2C_TXFIFO_WM_INT_RAW (BIT(1))
|
|
#define I2C_TXFIFO_WM_INT_RAW_M (I2C_TXFIFO_WM_INT_RAW_V << I2C_TXFIFO_WM_INT_RAW_S)
|
|
#define I2C_TXFIFO_WM_INT_RAW_V 0x00000001U
|
|
#define I2C_TXFIFO_WM_INT_RAW_S 1
|
|
/** I2C_RXFIFO_OVF_INT_RAW : R/SS/WTC; bitpos: [2]; default: 0;
|
|
* The raw interrupt bit for I2C_RXFIFO_OVF_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_OVF_INT_RAW (BIT(2))
|
|
#define I2C_RXFIFO_OVF_INT_RAW_M (I2C_RXFIFO_OVF_INT_RAW_V << I2C_RXFIFO_OVF_INT_RAW_S)
|
|
#define I2C_RXFIFO_OVF_INT_RAW_V 0x00000001U
|
|
#define I2C_RXFIFO_OVF_INT_RAW_S 2
|
|
/** I2C_END_DETECT_INT_RAW : R/SS/WTC; bitpos: [3]; default: 0;
|
|
* The raw interrupt bit for the I2C_END_DETECT_INT interrupt.
|
|
*/
|
|
#define I2C_END_DETECT_INT_RAW (BIT(3))
|
|
#define I2C_END_DETECT_INT_RAW_M (I2C_END_DETECT_INT_RAW_V << I2C_END_DETECT_INT_RAW_S)
|
|
#define I2C_END_DETECT_INT_RAW_V 0x00000001U
|
|
#define I2C_END_DETECT_INT_RAW_S 3
|
|
/** I2C_BYTE_TRANS_DONE_INT_RAW : R/SS/WTC; bitpos: [4]; default: 0;
|
|
* The raw interrupt bit for the I2C_END_DETECT_INT interrupt.
|
|
*/
|
|
#define I2C_BYTE_TRANS_DONE_INT_RAW (BIT(4))
|
|
#define I2C_BYTE_TRANS_DONE_INT_RAW_M (I2C_BYTE_TRANS_DONE_INT_RAW_V << I2C_BYTE_TRANS_DONE_INT_RAW_S)
|
|
#define I2C_BYTE_TRANS_DONE_INT_RAW_V 0x00000001U
|
|
#define I2C_BYTE_TRANS_DONE_INT_RAW_S 4
|
|
/** I2C_ARBITRATION_LOST_INT_RAW : R/SS/WTC; bitpos: [5]; default: 0;
|
|
* The raw interrupt bit for the I2C_ARBITRATION_LOST_INT interrupt.
|
|
*/
|
|
#define I2C_ARBITRATION_LOST_INT_RAW (BIT(5))
|
|
#define I2C_ARBITRATION_LOST_INT_RAW_M (I2C_ARBITRATION_LOST_INT_RAW_V << I2C_ARBITRATION_LOST_INT_RAW_S)
|
|
#define I2C_ARBITRATION_LOST_INT_RAW_V 0x00000001U
|
|
#define I2C_ARBITRATION_LOST_INT_RAW_S 5
|
|
/** I2C_MST_TXFIFO_UDF_INT_RAW : R/SS/WTC; bitpos: [6]; default: 0;
|
|
* The raw interrupt bit for I2C_TRANS_COMPLETE_INT interrupt.
|
|
*/
|
|
#define I2C_MST_TXFIFO_UDF_INT_RAW (BIT(6))
|
|
#define I2C_MST_TXFIFO_UDF_INT_RAW_M (I2C_MST_TXFIFO_UDF_INT_RAW_V << I2C_MST_TXFIFO_UDF_INT_RAW_S)
|
|
#define I2C_MST_TXFIFO_UDF_INT_RAW_V 0x00000001U
|
|
#define I2C_MST_TXFIFO_UDF_INT_RAW_S 6
|
|
/** I2C_TRANS_COMPLETE_INT_RAW : R/SS/WTC; bitpos: [7]; default: 0;
|
|
* The raw interrupt bit for the I2C_TRANS_COMPLETE_INT interrupt.
|
|
*/
|
|
#define I2C_TRANS_COMPLETE_INT_RAW (BIT(7))
|
|
#define I2C_TRANS_COMPLETE_INT_RAW_M (I2C_TRANS_COMPLETE_INT_RAW_V << I2C_TRANS_COMPLETE_INT_RAW_S)
|
|
#define I2C_TRANS_COMPLETE_INT_RAW_V 0x00000001U
|
|
#define I2C_TRANS_COMPLETE_INT_RAW_S 7
|
|
/** I2C_TIME_OUT_INT_RAW : R/SS/WTC; bitpos: [8]; default: 0;
|
|
* The raw interrupt bit for the I2C_TIME_OUT_INT interrupt.
|
|
*/
|
|
#define I2C_TIME_OUT_INT_RAW (BIT(8))
|
|
#define I2C_TIME_OUT_INT_RAW_M (I2C_TIME_OUT_INT_RAW_V << I2C_TIME_OUT_INT_RAW_S)
|
|
#define I2C_TIME_OUT_INT_RAW_V 0x00000001U
|
|
#define I2C_TIME_OUT_INT_RAW_S 8
|
|
/** I2C_TRANS_START_INT_RAW : R/SS/WTC; bitpos: [9]; default: 0;
|
|
* The raw interrupt bit for the I2C_TRANS_START_INT interrupt.
|
|
*/
|
|
#define I2C_TRANS_START_INT_RAW (BIT(9))
|
|
#define I2C_TRANS_START_INT_RAW_M (I2C_TRANS_START_INT_RAW_V << I2C_TRANS_START_INT_RAW_S)
|
|
#define I2C_TRANS_START_INT_RAW_V 0x00000001U
|
|
#define I2C_TRANS_START_INT_RAW_S 9
|
|
/** I2C_NACK_INT_RAW : R/SS/WTC; bitpos: [10]; default: 0;
|
|
* The raw interrupt bit for I2C_SLAVE_STRETCH_INT interrupt.
|
|
*/
|
|
#define I2C_NACK_INT_RAW (BIT(10))
|
|
#define I2C_NACK_INT_RAW_M (I2C_NACK_INT_RAW_V << I2C_NACK_INT_RAW_S)
|
|
#define I2C_NACK_INT_RAW_V 0x00000001U
|
|
#define I2C_NACK_INT_RAW_S 10
|
|
/** I2C_TXFIFO_OVF_INT_RAW : R/SS/WTC; bitpos: [11]; default: 0;
|
|
* The raw interrupt bit for I2C_TXFIFO_OVF_INT interrupt.
|
|
*/
|
|
#define I2C_TXFIFO_OVF_INT_RAW (BIT(11))
|
|
#define I2C_TXFIFO_OVF_INT_RAW_M (I2C_TXFIFO_OVF_INT_RAW_V << I2C_TXFIFO_OVF_INT_RAW_S)
|
|
#define I2C_TXFIFO_OVF_INT_RAW_V 0x00000001U
|
|
#define I2C_TXFIFO_OVF_INT_RAW_S 11
|
|
/** I2C_RXFIFO_UDF_INT_RAW : R/SS/WTC; bitpos: [12]; default: 0;
|
|
* The raw interrupt bit for I2C_RXFIFO_UDF_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_UDF_INT_RAW (BIT(12))
|
|
#define I2C_RXFIFO_UDF_INT_RAW_M (I2C_RXFIFO_UDF_INT_RAW_V << I2C_RXFIFO_UDF_INT_RAW_S)
|
|
#define I2C_RXFIFO_UDF_INT_RAW_V 0x00000001U
|
|
#define I2C_RXFIFO_UDF_INT_RAW_S 12
|
|
/** I2C_SCL_ST_TO_INT_RAW : R/SS/WTC; bitpos: [13]; default: 0;
|
|
* The raw interrupt bit for I2C_SCL_ST_TO_INT interrupt.
|
|
*/
|
|
#define I2C_SCL_ST_TO_INT_RAW (BIT(13))
|
|
#define I2C_SCL_ST_TO_INT_RAW_M (I2C_SCL_ST_TO_INT_RAW_V << I2C_SCL_ST_TO_INT_RAW_S)
|
|
#define I2C_SCL_ST_TO_INT_RAW_V 0x00000001U
|
|
#define I2C_SCL_ST_TO_INT_RAW_S 13
|
|
/** I2C_SCL_MAIN_ST_TO_INT_RAW : R/SS/WTC; bitpos: [14]; default: 0;
|
|
* The raw interrupt bit for I2C_SCL_MAIN_ST_TO_INT interrupt.
|
|
*/
|
|
#define I2C_SCL_MAIN_ST_TO_INT_RAW (BIT(14))
|
|
#define I2C_SCL_MAIN_ST_TO_INT_RAW_M (I2C_SCL_MAIN_ST_TO_INT_RAW_V << I2C_SCL_MAIN_ST_TO_INT_RAW_S)
|
|
#define I2C_SCL_MAIN_ST_TO_INT_RAW_V 0x00000001U
|
|
#define I2C_SCL_MAIN_ST_TO_INT_RAW_S 14
|
|
/** I2C_DET_START_INT_RAW : R/SS/WTC; bitpos: [15]; default: 0;
|
|
* The raw interrupt bit for I2C_DET_START_INT interrupt.
|
|
*/
|
|
#define I2C_DET_START_INT_RAW (BIT(15))
|
|
#define I2C_DET_START_INT_RAW_M (I2C_DET_START_INT_RAW_V << I2C_DET_START_INT_RAW_S)
|
|
#define I2C_DET_START_INT_RAW_V 0x00000001U
|
|
#define I2C_DET_START_INT_RAW_S 15
|
|
/** I2C_SLAVE_STRETCH_INT_RAW : R/SS/WTC; bitpos: [16]; default: 0;
|
|
* The raw interrupt bit for I2C_SLAVE_STRETCH_INT interrupt.
|
|
*/
|
|
#define I2C_SLAVE_STRETCH_INT_RAW (BIT(16))
|
|
#define I2C_SLAVE_STRETCH_INT_RAW_M (I2C_SLAVE_STRETCH_INT_RAW_V << I2C_SLAVE_STRETCH_INT_RAW_S)
|
|
#define I2C_SLAVE_STRETCH_INT_RAW_V 0x00000001U
|
|
#define I2C_SLAVE_STRETCH_INT_RAW_S 16
|
|
/** I2C_GENERAL_CALL_INT_RAW : R/SS/WTC; bitpos: [17]; default: 0;
|
|
* The raw interrupt bit for I2C_GENARAL_CALL_INT interrupt.
|
|
*/
|
|
#define I2C_GENERAL_CALL_INT_RAW (BIT(17))
|
|
#define I2C_GENERAL_CALL_INT_RAW_M (I2C_GENERAL_CALL_INT_RAW_V << I2C_GENERAL_CALL_INT_RAW_S)
|
|
#define I2C_GENERAL_CALL_INT_RAW_V 0x00000001U
|
|
#define I2C_GENERAL_CALL_INT_RAW_S 17
|
|
/** I2C_SLAVE_ADDR_UNMATCH_INT_RAW : R/SS/WTC; bitpos: [18]; default: 0;
|
|
* The raw interrupt bit for I2C_SLAVE_ADDR_UNMATCH_INT_RAW interrupt.
|
|
*/
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_RAW (BIT(18))
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_RAW_M (I2C_SLAVE_ADDR_UNMATCH_INT_RAW_V << I2C_SLAVE_ADDR_UNMATCH_INT_RAW_S)
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_RAW_V 0x00000001U
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_RAW_S 18
|
|
|
|
/** I2C_INT_CLR_REG register
|
|
* Interrupt clear bits
|
|
*/
|
|
#define I2C_INT_CLR_REG(i) (REG_I2C_BASE(i) + 0x24)
|
|
/** I2C_RXFIFO_WM_INT_CLR : WT; bitpos: [0]; default: 0;
|
|
* Set this bit to clear I2C_RXFIFO_WM_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_WM_INT_CLR (BIT(0))
|
|
#define I2C_RXFIFO_WM_INT_CLR_M (I2C_RXFIFO_WM_INT_CLR_V << I2C_RXFIFO_WM_INT_CLR_S)
|
|
#define I2C_RXFIFO_WM_INT_CLR_V 0x00000001U
|
|
#define I2C_RXFIFO_WM_INT_CLR_S 0
|
|
/** I2C_TXFIFO_WM_INT_CLR : WT; bitpos: [1]; default: 0;
|
|
* Set this bit to clear I2C_TXFIFO_WM_INT interrupt.
|
|
*/
|
|
#define I2C_TXFIFO_WM_INT_CLR (BIT(1))
|
|
#define I2C_TXFIFO_WM_INT_CLR_M (I2C_TXFIFO_WM_INT_CLR_V << I2C_TXFIFO_WM_INT_CLR_S)
|
|
#define I2C_TXFIFO_WM_INT_CLR_V 0x00000001U
|
|
#define I2C_TXFIFO_WM_INT_CLR_S 1
|
|
/** I2C_RXFIFO_OVF_INT_CLR : WT; bitpos: [2]; default: 0;
|
|
* Set this bit to clear I2C_RXFIFO_OVF_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_OVF_INT_CLR (BIT(2))
|
|
#define I2C_RXFIFO_OVF_INT_CLR_M (I2C_RXFIFO_OVF_INT_CLR_V << I2C_RXFIFO_OVF_INT_CLR_S)
|
|
#define I2C_RXFIFO_OVF_INT_CLR_V 0x00000001U
|
|
#define I2C_RXFIFO_OVF_INT_CLR_S 2
|
|
/** I2C_END_DETECT_INT_CLR : WT; bitpos: [3]; default: 0;
|
|
* Set this bit to clear the I2C_END_DETECT_INT interrupt.
|
|
*/
|
|
#define I2C_END_DETECT_INT_CLR (BIT(3))
|
|
#define I2C_END_DETECT_INT_CLR_M (I2C_END_DETECT_INT_CLR_V << I2C_END_DETECT_INT_CLR_S)
|
|
#define I2C_END_DETECT_INT_CLR_V 0x00000001U
|
|
#define I2C_END_DETECT_INT_CLR_S 3
|
|
/** I2C_BYTE_TRANS_DONE_INT_CLR : WT; bitpos: [4]; default: 0;
|
|
* Set this bit to clear the I2C_END_DETECT_INT interrupt.
|
|
*/
|
|
#define I2C_BYTE_TRANS_DONE_INT_CLR (BIT(4))
|
|
#define I2C_BYTE_TRANS_DONE_INT_CLR_M (I2C_BYTE_TRANS_DONE_INT_CLR_V << I2C_BYTE_TRANS_DONE_INT_CLR_S)
|
|
#define I2C_BYTE_TRANS_DONE_INT_CLR_V 0x00000001U
|
|
#define I2C_BYTE_TRANS_DONE_INT_CLR_S 4
|
|
/** I2C_ARBITRATION_LOST_INT_CLR : WT; bitpos: [5]; default: 0;
|
|
* Set this bit to clear the I2C_ARBITRATION_LOST_INT interrupt.
|
|
*/
|
|
#define I2C_ARBITRATION_LOST_INT_CLR (BIT(5))
|
|
#define I2C_ARBITRATION_LOST_INT_CLR_M (I2C_ARBITRATION_LOST_INT_CLR_V << I2C_ARBITRATION_LOST_INT_CLR_S)
|
|
#define I2C_ARBITRATION_LOST_INT_CLR_V 0x00000001U
|
|
#define I2C_ARBITRATION_LOST_INT_CLR_S 5
|
|
/** I2C_MST_TXFIFO_UDF_INT_CLR : WT; bitpos: [6]; default: 0;
|
|
* Set this bit to clear I2C_TRANS_COMPLETE_INT interrupt.
|
|
*/
|
|
#define I2C_MST_TXFIFO_UDF_INT_CLR (BIT(6))
|
|
#define I2C_MST_TXFIFO_UDF_INT_CLR_M (I2C_MST_TXFIFO_UDF_INT_CLR_V << I2C_MST_TXFIFO_UDF_INT_CLR_S)
|
|
#define I2C_MST_TXFIFO_UDF_INT_CLR_V 0x00000001U
|
|
#define I2C_MST_TXFIFO_UDF_INT_CLR_S 6
|
|
/** I2C_TRANS_COMPLETE_INT_CLR : WT; bitpos: [7]; default: 0;
|
|
* Set this bit to clear the I2C_TRANS_COMPLETE_INT interrupt.
|
|
*/
|
|
#define I2C_TRANS_COMPLETE_INT_CLR (BIT(7))
|
|
#define I2C_TRANS_COMPLETE_INT_CLR_M (I2C_TRANS_COMPLETE_INT_CLR_V << I2C_TRANS_COMPLETE_INT_CLR_S)
|
|
#define I2C_TRANS_COMPLETE_INT_CLR_V 0x00000001U
|
|
#define I2C_TRANS_COMPLETE_INT_CLR_S 7
|
|
/** I2C_TIME_OUT_INT_CLR : WT; bitpos: [8]; default: 0;
|
|
* Set this bit to clear the I2C_TIME_OUT_INT interrupt.
|
|
*/
|
|
#define I2C_TIME_OUT_INT_CLR (BIT(8))
|
|
#define I2C_TIME_OUT_INT_CLR_M (I2C_TIME_OUT_INT_CLR_V << I2C_TIME_OUT_INT_CLR_S)
|
|
#define I2C_TIME_OUT_INT_CLR_V 0x00000001U
|
|
#define I2C_TIME_OUT_INT_CLR_S 8
|
|
/** I2C_TRANS_START_INT_CLR : WT; bitpos: [9]; default: 0;
|
|
* Set this bit to clear the I2C_TRANS_START_INT interrupt.
|
|
*/
|
|
#define I2C_TRANS_START_INT_CLR (BIT(9))
|
|
#define I2C_TRANS_START_INT_CLR_M (I2C_TRANS_START_INT_CLR_V << I2C_TRANS_START_INT_CLR_S)
|
|
#define I2C_TRANS_START_INT_CLR_V 0x00000001U
|
|
#define I2C_TRANS_START_INT_CLR_S 9
|
|
/** I2C_NACK_INT_CLR : WT; bitpos: [10]; default: 0;
|
|
* Set this bit to clear I2C_SLAVE_STRETCH_INT interrupt.
|
|
*/
|
|
#define I2C_NACK_INT_CLR (BIT(10))
|
|
#define I2C_NACK_INT_CLR_M (I2C_NACK_INT_CLR_V << I2C_NACK_INT_CLR_S)
|
|
#define I2C_NACK_INT_CLR_V 0x00000001U
|
|
#define I2C_NACK_INT_CLR_S 10
|
|
/** I2C_TXFIFO_OVF_INT_CLR : WT; bitpos: [11]; default: 0;
|
|
* Set this bit to clear I2C_TXFIFO_OVF_INT interrupt.
|
|
*/
|
|
#define I2C_TXFIFO_OVF_INT_CLR (BIT(11))
|
|
#define I2C_TXFIFO_OVF_INT_CLR_M (I2C_TXFIFO_OVF_INT_CLR_V << I2C_TXFIFO_OVF_INT_CLR_S)
|
|
#define I2C_TXFIFO_OVF_INT_CLR_V 0x00000001U
|
|
#define I2C_TXFIFO_OVF_INT_CLR_S 11
|
|
/** I2C_RXFIFO_UDF_INT_CLR : WT; bitpos: [12]; default: 0;
|
|
* Set this bit to clear I2C_RXFIFO_UDF_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_UDF_INT_CLR (BIT(12))
|
|
#define I2C_RXFIFO_UDF_INT_CLR_M (I2C_RXFIFO_UDF_INT_CLR_V << I2C_RXFIFO_UDF_INT_CLR_S)
|
|
#define I2C_RXFIFO_UDF_INT_CLR_V 0x00000001U
|
|
#define I2C_RXFIFO_UDF_INT_CLR_S 12
|
|
/** I2C_SCL_ST_TO_INT_CLR : WT; bitpos: [13]; default: 0;
|
|
* Set this bit to clear I2C_SCL_ST_TO_INT interrupt.
|
|
*/
|
|
#define I2C_SCL_ST_TO_INT_CLR (BIT(13))
|
|
#define I2C_SCL_ST_TO_INT_CLR_M (I2C_SCL_ST_TO_INT_CLR_V << I2C_SCL_ST_TO_INT_CLR_S)
|
|
#define I2C_SCL_ST_TO_INT_CLR_V 0x00000001U
|
|
#define I2C_SCL_ST_TO_INT_CLR_S 13
|
|
/** I2C_SCL_MAIN_ST_TO_INT_CLR : WT; bitpos: [14]; default: 0;
|
|
* Set this bit to clear I2C_SCL_MAIN_ST_TO_INT interrupt.
|
|
*/
|
|
#define I2C_SCL_MAIN_ST_TO_INT_CLR (BIT(14))
|
|
#define I2C_SCL_MAIN_ST_TO_INT_CLR_M (I2C_SCL_MAIN_ST_TO_INT_CLR_V << I2C_SCL_MAIN_ST_TO_INT_CLR_S)
|
|
#define I2C_SCL_MAIN_ST_TO_INT_CLR_V 0x00000001U
|
|
#define I2C_SCL_MAIN_ST_TO_INT_CLR_S 14
|
|
/** I2C_DET_START_INT_CLR : WT; bitpos: [15]; default: 0;
|
|
* Set this bit to clear I2C_DET_START_INT interrupt.
|
|
*/
|
|
#define I2C_DET_START_INT_CLR (BIT(15))
|
|
#define I2C_DET_START_INT_CLR_M (I2C_DET_START_INT_CLR_V << I2C_DET_START_INT_CLR_S)
|
|
#define I2C_DET_START_INT_CLR_V 0x00000001U
|
|
#define I2C_DET_START_INT_CLR_S 15
|
|
/** I2C_SLAVE_STRETCH_INT_CLR : WT; bitpos: [16]; default: 0;
|
|
* Set this bit to clear I2C_SLAVE_STRETCH_INT interrupt.
|
|
*/
|
|
#define I2C_SLAVE_STRETCH_INT_CLR (BIT(16))
|
|
#define I2C_SLAVE_STRETCH_INT_CLR_M (I2C_SLAVE_STRETCH_INT_CLR_V << I2C_SLAVE_STRETCH_INT_CLR_S)
|
|
#define I2C_SLAVE_STRETCH_INT_CLR_V 0x00000001U
|
|
#define I2C_SLAVE_STRETCH_INT_CLR_S 16
|
|
/** I2C_GENERAL_CALL_INT_CLR : WT; bitpos: [17]; default: 0;
|
|
* Set this bit to clear I2C_GENARAL_CALL_INT interrupt.
|
|
*/
|
|
#define I2C_GENERAL_CALL_INT_CLR (BIT(17))
|
|
#define I2C_GENERAL_CALL_INT_CLR_M (I2C_GENERAL_CALL_INT_CLR_V << I2C_GENERAL_CALL_INT_CLR_S)
|
|
#define I2C_GENERAL_CALL_INT_CLR_V 0x00000001U
|
|
#define I2C_GENERAL_CALL_INT_CLR_S 17
|
|
/** I2C_SLAVE_ADDR_UNMATCH_INT_CLR : WT; bitpos: [18]; default: 0;
|
|
* Set this bit to clear I2C_SLAVE_ADDR_UNMATCH_INT_RAW interrupt.
|
|
*/
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_CLR (BIT(18))
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_CLR_M (I2C_SLAVE_ADDR_UNMATCH_INT_CLR_V << I2C_SLAVE_ADDR_UNMATCH_INT_CLR_S)
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_CLR_V 0x00000001U
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_CLR_S 18
|
|
|
|
/** I2C_INT_ENA_REG register
|
|
* Interrupt enable bits
|
|
*/
|
|
#define I2C_INT_ENA_REG(i) (REG_I2C_BASE(i) + 0x28)
|
|
/** I2C_RXFIFO_WM_INT_ENA : R/W; bitpos: [0]; default: 0;
|
|
* The interrupt enable bit for I2C_RXFIFO_WM_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_WM_INT_ENA (BIT(0))
|
|
#define I2C_RXFIFO_WM_INT_ENA_M (I2C_RXFIFO_WM_INT_ENA_V << I2C_RXFIFO_WM_INT_ENA_S)
|
|
#define I2C_RXFIFO_WM_INT_ENA_V 0x00000001U
|
|
#define I2C_RXFIFO_WM_INT_ENA_S 0
|
|
/** I2C_TXFIFO_WM_INT_ENA : R/W; bitpos: [1]; default: 0;
|
|
* The interrupt enable bit for I2C_TXFIFO_WM_INT interrupt.
|
|
*/
|
|
#define I2C_TXFIFO_WM_INT_ENA (BIT(1))
|
|
#define I2C_TXFIFO_WM_INT_ENA_M (I2C_TXFIFO_WM_INT_ENA_V << I2C_TXFIFO_WM_INT_ENA_S)
|
|
#define I2C_TXFIFO_WM_INT_ENA_V 0x00000001U
|
|
#define I2C_TXFIFO_WM_INT_ENA_S 1
|
|
/** I2C_RXFIFO_OVF_INT_ENA : R/W; bitpos: [2]; default: 0;
|
|
* The interrupt enable bit for I2C_RXFIFO_OVF_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_OVF_INT_ENA (BIT(2))
|
|
#define I2C_RXFIFO_OVF_INT_ENA_M (I2C_RXFIFO_OVF_INT_ENA_V << I2C_RXFIFO_OVF_INT_ENA_S)
|
|
#define I2C_RXFIFO_OVF_INT_ENA_V 0x00000001U
|
|
#define I2C_RXFIFO_OVF_INT_ENA_S 2
|
|
/** I2C_END_DETECT_INT_ENA : R/W; bitpos: [3]; default: 0;
|
|
* The interrupt enable bit for the I2C_END_DETECT_INT interrupt.
|
|
*/
|
|
#define I2C_END_DETECT_INT_ENA (BIT(3))
|
|
#define I2C_END_DETECT_INT_ENA_M (I2C_END_DETECT_INT_ENA_V << I2C_END_DETECT_INT_ENA_S)
|
|
#define I2C_END_DETECT_INT_ENA_V 0x00000001U
|
|
#define I2C_END_DETECT_INT_ENA_S 3
|
|
/** I2C_BYTE_TRANS_DONE_INT_ENA : R/W; bitpos: [4]; default: 0;
|
|
* The interrupt enable bit for the I2C_END_DETECT_INT interrupt.
|
|
*/
|
|
#define I2C_BYTE_TRANS_DONE_INT_ENA (BIT(4))
|
|
#define I2C_BYTE_TRANS_DONE_INT_ENA_M (I2C_BYTE_TRANS_DONE_INT_ENA_V << I2C_BYTE_TRANS_DONE_INT_ENA_S)
|
|
#define I2C_BYTE_TRANS_DONE_INT_ENA_V 0x00000001U
|
|
#define I2C_BYTE_TRANS_DONE_INT_ENA_S 4
|
|
/** I2C_ARBITRATION_LOST_INT_ENA : R/W; bitpos: [5]; default: 0;
|
|
* The interrupt enable bit for the I2C_ARBITRATION_LOST_INT interrupt.
|
|
*/
|
|
#define I2C_ARBITRATION_LOST_INT_ENA (BIT(5))
|
|
#define I2C_ARBITRATION_LOST_INT_ENA_M (I2C_ARBITRATION_LOST_INT_ENA_V << I2C_ARBITRATION_LOST_INT_ENA_S)
|
|
#define I2C_ARBITRATION_LOST_INT_ENA_V 0x00000001U
|
|
#define I2C_ARBITRATION_LOST_INT_ENA_S 5
|
|
/** I2C_MST_TXFIFO_UDF_INT_ENA : R/W; bitpos: [6]; default: 0;
|
|
* The interrupt enable bit for I2C_TRANS_COMPLETE_INT interrupt.
|
|
*/
|
|
#define I2C_MST_TXFIFO_UDF_INT_ENA (BIT(6))
|
|
#define I2C_MST_TXFIFO_UDF_INT_ENA_M (I2C_MST_TXFIFO_UDF_INT_ENA_V << I2C_MST_TXFIFO_UDF_INT_ENA_S)
|
|
#define I2C_MST_TXFIFO_UDF_INT_ENA_V 0x00000001U
|
|
#define I2C_MST_TXFIFO_UDF_INT_ENA_S 6
|
|
/** I2C_TRANS_COMPLETE_INT_ENA : R/W; bitpos: [7]; default: 0;
|
|
* The interrupt enable bit for the I2C_TRANS_COMPLETE_INT interrupt.
|
|
*/
|
|
#define I2C_TRANS_COMPLETE_INT_ENA (BIT(7))
|
|
#define I2C_TRANS_COMPLETE_INT_ENA_M (I2C_TRANS_COMPLETE_INT_ENA_V << I2C_TRANS_COMPLETE_INT_ENA_S)
|
|
#define I2C_TRANS_COMPLETE_INT_ENA_V 0x00000001U
|
|
#define I2C_TRANS_COMPLETE_INT_ENA_S 7
|
|
/** I2C_TIME_OUT_INT_ENA : R/W; bitpos: [8]; default: 0;
|
|
* The interrupt enable bit for the I2C_TIME_OUT_INT interrupt.
|
|
*/
|
|
#define I2C_TIME_OUT_INT_ENA (BIT(8))
|
|
#define I2C_TIME_OUT_INT_ENA_M (I2C_TIME_OUT_INT_ENA_V << I2C_TIME_OUT_INT_ENA_S)
|
|
#define I2C_TIME_OUT_INT_ENA_V 0x00000001U
|
|
#define I2C_TIME_OUT_INT_ENA_S 8
|
|
/** I2C_TRANS_START_INT_ENA : R/W; bitpos: [9]; default: 0;
|
|
* The interrupt enable bit for the I2C_TRANS_START_INT interrupt.
|
|
*/
|
|
#define I2C_TRANS_START_INT_ENA (BIT(9))
|
|
#define I2C_TRANS_START_INT_ENA_M (I2C_TRANS_START_INT_ENA_V << I2C_TRANS_START_INT_ENA_S)
|
|
#define I2C_TRANS_START_INT_ENA_V 0x00000001U
|
|
#define I2C_TRANS_START_INT_ENA_S 9
|
|
/** I2C_NACK_INT_ENA : R/W; bitpos: [10]; default: 0;
|
|
* The interrupt enable bit for I2C_SLAVE_STRETCH_INT interrupt.
|
|
*/
|
|
#define I2C_NACK_INT_ENA (BIT(10))
|
|
#define I2C_NACK_INT_ENA_M (I2C_NACK_INT_ENA_V << I2C_NACK_INT_ENA_S)
|
|
#define I2C_NACK_INT_ENA_V 0x00000001U
|
|
#define I2C_NACK_INT_ENA_S 10
|
|
/** I2C_TXFIFO_OVF_INT_ENA : R/W; bitpos: [11]; default: 0;
|
|
* The interrupt enable bit for I2C_TXFIFO_OVF_INT interrupt.
|
|
*/
|
|
#define I2C_TXFIFO_OVF_INT_ENA (BIT(11))
|
|
#define I2C_TXFIFO_OVF_INT_ENA_M (I2C_TXFIFO_OVF_INT_ENA_V << I2C_TXFIFO_OVF_INT_ENA_S)
|
|
#define I2C_TXFIFO_OVF_INT_ENA_V 0x00000001U
|
|
#define I2C_TXFIFO_OVF_INT_ENA_S 11
|
|
/** I2C_RXFIFO_UDF_INT_ENA : R/W; bitpos: [12]; default: 0;
|
|
* The interrupt enable bit for I2C_RXFIFO_UDF_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_UDF_INT_ENA (BIT(12))
|
|
#define I2C_RXFIFO_UDF_INT_ENA_M (I2C_RXFIFO_UDF_INT_ENA_V << I2C_RXFIFO_UDF_INT_ENA_S)
|
|
#define I2C_RXFIFO_UDF_INT_ENA_V 0x00000001U
|
|
#define I2C_RXFIFO_UDF_INT_ENA_S 12
|
|
/** I2C_SCL_ST_TO_INT_ENA : R/W; bitpos: [13]; default: 0;
|
|
* The interrupt enable bit for I2C_SCL_ST_TO_INT interrupt.
|
|
*/
|
|
#define I2C_SCL_ST_TO_INT_ENA (BIT(13))
|
|
#define I2C_SCL_ST_TO_INT_ENA_M (I2C_SCL_ST_TO_INT_ENA_V << I2C_SCL_ST_TO_INT_ENA_S)
|
|
#define I2C_SCL_ST_TO_INT_ENA_V 0x00000001U
|
|
#define I2C_SCL_ST_TO_INT_ENA_S 13
|
|
/** I2C_SCL_MAIN_ST_TO_INT_ENA : R/W; bitpos: [14]; default: 0;
|
|
* The interrupt enable bit for I2C_SCL_MAIN_ST_TO_INT interrupt.
|
|
*/
|
|
#define I2C_SCL_MAIN_ST_TO_INT_ENA (BIT(14))
|
|
#define I2C_SCL_MAIN_ST_TO_INT_ENA_M (I2C_SCL_MAIN_ST_TO_INT_ENA_V << I2C_SCL_MAIN_ST_TO_INT_ENA_S)
|
|
#define I2C_SCL_MAIN_ST_TO_INT_ENA_V 0x00000001U
|
|
#define I2C_SCL_MAIN_ST_TO_INT_ENA_S 14
|
|
/** I2C_DET_START_INT_ENA : R/W; bitpos: [15]; default: 0;
|
|
* The interrupt enable bit for I2C_DET_START_INT interrupt.
|
|
*/
|
|
#define I2C_DET_START_INT_ENA (BIT(15))
|
|
#define I2C_DET_START_INT_ENA_M (I2C_DET_START_INT_ENA_V << I2C_DET_START_INT_ENA_S)
|
|
#define I2C_DET_START_INT_ENA_V 0x00000001U
|
|
#define I2C_DET_START_INT_ENA_S 15
|
|
/** I2C_SLAVE_STRETCH_INT_ENA : R/W; bitpos: [16]; default: 0;
|
|
* The interrupt enable bit for I2C_SLAVE_STRETCH_INT interrupt.
|
|
*/
|
|
#define I2C_SLAVE_STRETCH_INT_ENA (BIT(16))
|
|
#define I2C_SLAVE_STRETCH_INT_ENA_M (I2C_SLAVE_STRETCH_INT_ENA_V << I2C_SLAVE_STRETCH_INT_ENA_S)
|
|
#define I2C_SLAVE_STRETCH_INT_ENA_V 0x00000001U
|
|
#define I2C_SLAVE_STRETCH_INT_ENA_S 16
|
|
/** I2C_GENERAL_CALL_INT_ENA : R/W; bitpos: [17]; default: 0;
|
|
* The interrupt enable bit for I2C_GENARAL_CALL_INT interrupt.
|
|
*/
|
|
#define I2C_GENERAL_CALL_INT_ENA (BIT(17))
|
|
#define I2C_GENERAL_CALL_INT_ENA_M (I2C_GENERAL_CALL_INT_ENA_V << I2C_GENERAL_CALL_INT_ENA_S)
|
|
#define I2C_GENERAL_CALL_INT_ENA_V 0x00000001U
|
|
#define I2C_GENERAL_CALL_INT_ENA_S 17
|
|
/** I2C_SLAVE_ADDR_UNMATCH_INT_ENA : R/W; bitpos: [18]; default: 0;
|
|
* The interrupt enable bit for I2C_SLAVE_ADDR_UNMATCH_INT interrupt.
|
|
*/
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_ENA (BIT(18))
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_ENA_M (I2C_SLAVE_ADDR_UNMATCH_INT_ENA_V << I2C_SLAVE_ADDR_UNMATCH_INT_ENA_S)
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_ENA_V 0x00000001U
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_ENA_S 18
|
|
|
|
/** I2C_INT_STATUS_REG register
|
|
* Status of captured I2C communication events
|
|
*/
|
|
#define I2C_INT_STATUS_REG(i) (REG_I2C_BASE(i) + 0x2c)
|
|
/** I2C_RXFIFO_WM_INT_ST : RO; bitpos: [0]; default: 0;
|
|
* The masked interrupt status bit for I2C_RXFIFO_WM_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_WM_INT_ST (BIT(0))
|
|
#define I2C_RXFIFO_WM_INT_ST_M (I2C_RXFIFO_WM_INT_ST_V << I2C_RXFIFO_WM_INT_ST_S)
|
|
#define I2C_RXFIFO_WM_INT_ST_V 0x00000001U
|
|
#define I2C_RXFIFO_WM_INT_ST_S 0
|
|
/** I2C_TXFIFO_WM_INT_ST : RO; bitpos: [1]; default: 0;
|
|
* The masked interrupt status bit for I2C_TXFIFO_WM_INT interrupt.
|
|
*/
|
|
#define I2C_TXFIFO_WM_INT_ST (BIT(1))
|
|
#define I2C_TXFIFO_WM_INT_ST_M (I2C_TXFIFO_WM_INT_ST_V << I2C_TXFIFO_WM_INT_ST_S)
|
|
#define I2C_TXFIFO_WM_INT_ST_V 0x00000001U
|
|
#define I2C_TXFIFO_WM_INT_ST_S 1
|
|
/** I2C_RXFIFO_OVF_INT_ST : RO; bitpos: [2]; default: 0;
|
|
* The masked interrupt status bit for I2C_RXFIFO_OVF_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_OVF_INT_ST (BIT(2))
|
|
#define I2C_RXFIFO_OVF_INT_ST_M (I2C_RXFIFO_OVF_INT_ST_V << I2C_RXFIFO_OVF_INT_ST_S)
|
|
#define I2C_RXFIFO_OVF_INT_ST_V 0x00000001U
|
|
#define I2C_RXFIFO_OVF_INT_ST_S 2
|
|
/** I2C_END_DETECT_INT_ST : RO; bitpos: [3]; default: 0;
|
|
* The masked interrupt status bit for the I2C_END_DETECT_INT interrupt.
|
|
*/
|
|
#define I2C_END_DETECT_INT_ST (BIT(3))
|
|
#define I2C_END_DETECT_INT_ST_M (I2C_END_DETECT_INT_ST_V << I2C_END_DETECT_INT_ST_S)
|
|
#define I2C_END_DETECT_INT_ST_V 0x00000001U
|
|
#define I2C_END_DETECT_INT_ST_S 3
|
|
/** I2C_BYTE_TRANS_DONE_INT_ST : RO; bitpos: [4]; default: 0;
|
|
* The masked interrupt status bit for the I2C_END_DETECT_INT interrupt.
|
|
*/
|
|
#define I2C_BYTE_TRANS_DONE_INT_ST (BIT(4))
|
|
#define I2C_BYTE_TRANS_DONE_INT_ST_M (I2C_BYTE_TRANS_DONE_INT_ST_V << I2C_BYTE_TRANS_DONE_INT_ST_S)
|
|
#define I2C_BYTE_TRANS_DONE_INT_ST_V 0x00000001U
|
|
#define I2C_BYTE_TRANS_DONE_INT_ST_S 4
|
|
/** I2C_ARBITRATION_LOST_INT_ST : RO; bitpos: [5]; default: 0;
|
|
* The masked interrupt status bit for the I2C_ARBITRATION_LOST_INT interrupt.
|
|
*/
|
|
#define I2C_ARBITRATION_LOST_INT_ST (BIT(5))
|
|
#define I2C_ARBITRATION_LOST_INT_ST_M (I2C_ARBITRATION_LOST_INT_ST_V << I2C_ARBITRATION_LOST_INT_ST_S)
|
|
#define I2C_ARBITRATION_LOST_INT_ST_V 0x00000001U
|
|
#define I2C_ARBITRATION_LOST_INT_ST_S 5
|
|
/** I2C_MST_TXFIFO_UDF_INT_ST : RO; bitpos: [6]; default: 0;
|
|
* The masked interrupt status bit for I2C_TRANS_COMPLETE_INT interrupt.
|
|
*/
|
|
#define I2C_MST_TXFIFO_UDF_INT_ST (BIT(6))
|
|
#define I2C_MST_TXFIFO_UDF_INT_ST_M (I2C_MST_TXFIFO_UDF_INT_ST_V << I2C_MST_TXFIFO_UDF_INT_ST_S)
|
|
#define I2C_MST_TXFIFO_UDF_INT_ST_V 0x00000001U
|
|
#define I2C_MST_TXFIFO_UDF_INT_ST_S 6
|
|
/** I2C_TRANS_COMPLETE_INT_ST : RO; bitpos: [7]; default: 0;
|
|
* The masked interrupt status bit for the I2C_TRANS_COMPLETE_INT interrupt.
|
|
*/
|
|
#define I2C_TRANS_COMPLETE_INT_ST (BIT(7))
|
|
#define I2C_TRANS_COMPLETE_INT_ST_M (I2C_TRANS_COMPLETE_INT_ST_V << I2C_TRANS_COMPLETE_INT_ST_S)
|
|
#define I2C_TRANS_COMPLETE_INT_ST_V 0x00000001U
|
|
#define I2C_TRANS_COMPLETE_INT_ST_S 7
|
|
/** I2C_TIME_OUT_INT_ST : RO; bitpos: [8]; default: 0;
|
|
* The masked interrupt status bit for the I2C_TIME_OUT_INT interrupt.
|
|
*/
|
|
#define I2C_TIME_OUT_INT_ST (BIT(8))
|
|
#define I2C_TIME_OUT_INT_ST_M (I2C_TIME_OUT_INT_ST_V << I2C_TIME_OUT_INT_ST_S)
|
|
#define I2C_TIME_OUT_INT_ST_V 0x00000001U
|
|
#define I2C_TIME_OUT_INT_ST_S 8
|
|
/** I2C_TRANS_START_INT_ST : RO; bitpos: [9]; default: 0;
|
|
* The masked interrupt status bit for the I2C_TRANS_START_INT interrupt.
|
|
*/
|
|
#define I2C_TRANS_START_INT_ST (BIT(9))
|
|
#define I2C_TRANS_START_INT_ST_M (I2C_TRANS_START_INT_ST_V << I2C_TRANS_START_INT_ST_S)
|
|
#define I2C_TRANS_START_INT_ST_V 0x00000001U
|
|
#define I2C_TRANS_START_INT_ST_S 9
|
|
/** I2C_NACK_INT_ST : RO; bitpos: [10]; default: 0;
|
|
* The masked interrupt status bit for I2C_SLAVE_STRETCH_INT interrupt.
|
|
*/
|
|
#define I2C_NACK_INT_ST (BIT(10))
|
|
#define I2C_NACK_INT_ST_M (I2C_NACK_INT_ST_V << I2C_NACK_INT_ST_S)
|
|
#define I2C_NACK_INT_ST_V 0x00000001U
|
|
#define I2C_NACK_INT_ST_S 10
|
|
/** I2C_TXFIFO_OVF_INT_ST : RO; bitpos: [11]; default: 0;
|
|
* The masked interrupt status bit for I2C_TXFIFO_OVF_INT interrupt.
|
|
*/
|
|
#define I2C_TXFIFO_OVF_INT_ST (BIT(11))
|
|
#define I2C_TXFIFO_OVF_INT_ST_M (I2C_TXFIFO_OVF_INT_ST_V << I2C_TXFIFO_OVF_INT_ST_S)
|
|
#define I2C_TXFIFO_OVF_INT_ST_V 0x00000001U
|
|
#define I2C_TXFIFO_OVF_INT_ST_S 11
|
|
/** I2C_RXFIFO_UDF_INT_ST : RO; bitpos: [12]; default: 0;
|
|
* The masked interrupt status bit for I2C_RXFIFO_UDF_INT interrupt.
|
|
*/
|
|
#define I2C_RXFIFO_UDF_INT_ST (BIT(12))
|
|
#define I2C_RXFIFO_UDF_INT_ST_M (I2C_RXFIFO_UDF_INT_ST_V << I2C_RXFIFO_UDF_INT_ST_S)
|
|
#define I2C_RXFIFO_UDF_INT_ST_V 0x00000001U
|
|
#define I2C_RXFIFO_UDF_INT_ST_S 12
|
|
/** I2C_SCL_ST_TO_INT_ST : RO; bitpos: [13]; default: 0;
|
|
* The masked interrupt status bit for I2C_SCL_ST_TO_INT interrupt.
|
|
*/
|
|
#define I2C_SCL_ST_TO_INT_ST (BIT(13))
|
|
#define I2C_SCL_ST_TO_INT_ST_M (I2C_SCL_ST_TO_INT_ST_V << I2C_SCL_ST_TO_INT_ST_S)
|
|
#define I2C_SCL_ST_TO_INT_ST_V 0x00000001U
|
|
#define I2C_SCL_ST_TO_INT_ST_S 13
|
|
/** I2C_SCL_MAIN_ST_TO_INT_ST : RO; bitpos: [14]; default: 0;
|
|
* The masked interrupt status bit for I2C_SCL_MAIN_ST_TO_INT interrupt.
|
|
*/
|
|
#define I2C_SCL_MAIN_ST_TO_INT_ST (BIT(14))
|
|
#define I2C_SCL_MAIN_ST_TO_INT_ST_M (I2C_SCL_MAIN_ST_TO_INT_ST_V << I2C_SCL_MAIN_ST_TO_INT_ST_S)
|
|
#define I2C_SCL_MAIN_ST_TO_INT_ST_V 0x00000001U
|
|
#define I2C_SCL_MAIN_ST_TO_INT_ST_S 14
|
|
/** I2C_DET_START_INT_ST : RO; bitpos: [15]; default: 0;
|
|
* The masked interrupt status bit for I2C_DET_START_INT interrupt.
|
|
*/
|
|
#define I2C_DET_START_INT_ST (BIT(15))
|
|
#define I2C_DET_START_INT_ST_M (I2C_DET_START_INT_ST_V << I2C_DET_START_INT_ST_S)
|
|
#define I2C_DET_START_INT_ST_V 0x00000001U
|
|
#define I2C_DET_START_INT_ST_S 15
|
|
/** I2C_SLAVE_STRETCH_INT_ST : RO; bitpos: [16]; default: 0;
|
|
* The masked interrupt status bit for I2C_SLAVE_STRETCH_INT interrupt.
|
|
*/
|
|
#define I2C_SLAVE_STRETCH_INT_ST (BIT(16))
|
|
#define I2C_SLAVE_STRETCH_INT_ST_M (I2C_SLAVE_STRETCH_INT_ST_V << I2C_SLAVE_STRETCH_INT_ST_S)
|
|
#define I2C_SLAVE_STRETCH_INT_ST_V 0x00000001U
|
|
#define I2C_SLAVE_STRETCH_INT_ST_S 16
|
|
/** I2C_GENERAL_CALL_INT_ST : RO; bitpos: [17]; default: 0;
|
|
* The masked interrupt status bit for I2C_GENARAL_CALL_INT interrupt.
|
|
*/
|
|
#define I2C_GENERAL_CALL_INT_ST (BIT(17))
|
|
#define I2C_GENERAL_CALL_INT_ST_M (I2C_GENERAL_CALL_INT_ST_V << I2C_GENERAL_CALL_INT_ST_S)
|
|
#define I2C_GENERAL_CALL_INT_ST_V 0x00000001U
|
|
#define I2C_GENERAL_CALL_INT_ST_S 17
|
|
/** I2C_SLAVE_ADDR_UNMATCH_INT_ST : RO; bitpos: [18]; default: 0;
|
|
* The masked interrupt status bit for I2C_SLAVE_ADDR_UNMATCH_INT interrupt.
|
|
*/
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_ST (BIT(18))
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_ST_M (I2C_SLAVE_ADDR_UNMATCH_INT_ST_V << I2C_SLAVE_ADDR_UNMATCH_INT_ST_S)
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_ST_V 0x00000001U
|
|
#define I2C_SLAVE_ADDR_UNMATCH_INT_ST_S 18
|
|
|
|
/** I2C_SDA_HOLD_REG register
|
|
* Configures the hold time after a negative SCL edge.
|
|
*/
|
|
#define I2C_SDA_HOLD_REG(i) (REG_I2C_BASE(i) + 0x30)
|
|
/** I2C_SDA_HOLD_TIME : R/W; bitpos: [8:0]; default: 0;
|
|
* This register is used to configure the time to hold the data after the negative
|
|
* edge of SCL, in I2C module clock cycles.
|
|
*/
|
|
#define I2C_SDA_HOLD_TIME 0x000001FFU
|
|
#define I2C_SDA_HOLD_TIME_M (I2C_SDA_HOLD_TIME_V << I2C_SDA_HOLD_TIME_S)
|
|
#define I2C_SDA_HOLD_TIME_V 0x000001FFU
|
|
#define I2C_SDA_HOLD_TIME_S 0
|
|
|
|
/** I2C_SDA_SAMPLE_REG register
|
|
* Configures the sample time after a positive SCL edge.
|
|
*/
|
|
#define I2C_SDA_SAMPLE_REG(i) (REG_I2C_BASE(i) + 0x34)
|
|
/** I2C_SDA_SAMPLE_TIME : R/W; bitpos: [8:0]; default: 0;
|
|
* This register is used to configure for how long SDA is sampled, in I2C module clock
|
|
* cycles.
|
|
*/
|
|
#define I2C_SDA_SAMPLE_TIME 0x000001FFU
|
|
#define I2C_SDA_SAMPLE_TIME_M (I2C_SDA_SAMPLE_TIME_V << I2C_SDA_SAMPLE_TIME_S)
|
|
#define I2C_SDA_SAMPLE_TIME_V 0x000001FFU
|
|
#define I2C_SDA_SAMPLE_TIME_S 0
|
|
|
|
/** I2C_SCL_HIGH_PERIOD_REG register
|
|
* Configures the high level width of SCL
|
|
*/
|
|
#define I2C_SCL_HIGH_PERIOD_REG(i) (REG_I2C_BASE(i) + 0x38)
|
|
/** I2C_SCL_HIGH_PERIOD : R/W; bitpos: [8:0]; default: 0;
|
|
* This register is used to configure for how long SCL remains high in master mode, in
|
|
* I2C module clock cycles.
|
|
*/
|
|
#define I2C_SCL_HIGH_PERIOD 0x000001FFU
|
|
#define I2C_SCL_HIGH_PERIOD_M (I2C_SCL_HIGH_PERIOD_V << I2C_SCL_HIGH_PERIOD_S)
|
|
#define I2C_SCL_HIGH_PERIOD_V 0x000001FFU
|
|
#define I2C_SCL_HIGH_PERIOD_S 0
|
|
/** I2C_SCL_WAIT_HIGH_PERIOD : R/W; bitpos: [15:9]; default: 0;
|
|
* This register is used to configure for the SCL_FSM's waiting period for SCL high
|
|
* level in master mode, in I2C module clock cycles.
|
|
*/
|
|
#define I2C_SCL_WAIT_HIGH_PERIOD 0x0000007FU
|
|
#define I2C_SCL_WAIT_HIGH_PERIOD_M (I2C_SCL_WAIT_HIGH_PERIOD_V << I2C_SCL_WAIT_HIGH_PERIOD_S)
|
|
#define I2C_SCL_WAIT_HIGH_PERIOD_V 0x0000007FU
|
|
#define I2C_SCL_WAIT_HIGH_PERIOD_S 9
|
|
|
|
/** I2C_SCL_START_HOLD_REG register
|
|
* Configures the delay between the SDA and SCL negative edge for a start condition
|
|
*/
|
|
#define I2C_SCL_START_HOLD_REG(i) (REG_I2C_BASE(i) + 0x40)
|
|
/** I2C_SCL_START_HOLD_TIME : R/W; bitpos: [8:0]; default: 8;
|
|
* This register is used to configure the time between the negative edge
|
|
* of SDA and the negative edge of SCL for a START condition, in I2C module clock
|
|
* cycles.
|
|
*/
|
|
#define I2C_SCL_START_HOLD_TIME 0x000001FFU
|
|
#define I2C_SCL_START_HOLD_TIME_M (I2C_SCL_START_HOLD_TIME_V << I2C_SCL_START_HOLD_TIME_S)
|
|
#define I2C_SCL_START_HOLD_TIME_V 0x000001FFU
|
|
#define I2C_SCL_START_HOLD_TIME_S 0
|
|
|
|
/** I2C_SCL_RSTART_SETUP_REG register
|
|
* Configures the delay between the positive
|
|
* edge of SCL and the negative edge of SDA
|
|
*/
|
|
#define I2C_SCL_RSTART_SETUP_REG(i) (REG_I2C_BASE(i) + 0x44)
|
|
/** I2C_SCL_RSTART_SETUP_TIME : R/W; bitpos: [8:0]; default: 8;
|
|
* This register is used to configure the time between the positive
|
|
* edge of SCL and the negative edge of SDA for a RESTART condition, in I2C module
|
|
* clock cycles.
|
|
*/
|
|
#define I2C_SCL_RSTART_SETUP_TIME 0x000001FFU
|
|
#define I2C_SCL_RSTART_SETUP_TIME_M (I2C_SCL_RSTART_SETUP_TIME_V << I2C_SCL_RSTART_SETUP_TIME_S)
|
|
#define I2C_SCL_RSTART_SETUP_TIME_V 0x000001FFU
|
|
#define I2C_SCL_RSTART_SETUP_TIME_S 0
|
|
|
|
/** I2C_SCL_STOP_HOLD_REG register
|
|
* Configures the delay after the SCL clock
|
|
* edge for a stop condition
|
|
*/
|
|
#define I2C_SCL_STOP_HOLD_REG(i) (REG_I2C_BASE(i) + 0x48)
|
|
/** I2C_SCL_STOP_HOLD_TIME : R/W; bitpos: [8:0]; default: 8;
|
|
* This register is used to configure the delay after the STOP condition,
|
|
* in I2C module clock cycles.
|
|
*/
|
|
#define I2C_SCL_STOP_HOLD_TIME 0x000001FFU
|
|
#define I2C_SCL_STOP_HOLD_TIME_M (I2C_SCL_STOP_HOLD_TIME_V << I2C_SCL_STOP_HOLD_TIME_S)
|
|
#define I2C_SCL_STOP_HOLD_TIME_V 0x000001FFU
|
|
#define I2C_SCL_STOP_HOLD_TIME_S 0
|
|
|
|
/** I2C_SCL_STOP_SETUP_REG register
|
|
* Configures the delay between the SDA and
|
|
* SCL positive edge for a stop condition
|
|
*/
|
|
#define I2C_SCL_STOP_SETUP_REG(i) (REG_I2C_BASE(i) + 0x4c)
|
|
/** I2C_SCL_STOP_SETUP_TIME : R/W; bitpos: [8:0]; default: 8;
|
|
* This register is used to configure the time between the positive edge
|
|
* of SCL and the positive edge of SDA, in I2C module clock cycles.
|
|
*/
|
|
#define I2C_SCL_STOP_SETUP_TIME 0x000001FFU
|
|
#define I2C_SCL_STOP_SETUP_TIME_M (I2C_SCL_STOP_SETUP_TIME_V << I2C_SCL_STOP_SETUP_TIME_S)
|
|
#define I2C_SCL_STOP_SETUP_TIME_V 0x000001FFU
|
|
#define I2C_SCL_STOP_SETUP_TIME_S 0
|
|
|
|
/** I2C_FILTER_CFG_REG register
|
|
* SCL and SDA filter configuration register
|
|
*/
|
|
#define I2C_FILTER_CFG_REG(i) (REG_I2C_BASE(i) + 0x50)
|
|
/** I2C_SCL_FILTER_THRES : R/W; bitpos: [3:0]; default: 0;
|
|
* When a pulse on the SCL input has smaller width than this register value
|
|
* in I2C module clock cycles, the I2C controller will ignore that pulse.
|
|
*/
|
|
#define I2C_SCL_FILTER_THRES 0x0000000FU
|
|
#define I2C_SCL_FILTER_THRES_M (I2C_SCL_FILTER_THRES_V << I2C_SCL_FILTER_THRES_S)
|
|
#define I2C_SCL_FILTER_THRES_V 0x0000000FU
|
|
#define I2C_SCL_FILTER_THRES_S 0
|
|
/** I2C_SDA_FILTER_THRES : R/W; bitpos: [7:4]; default: 0;
|
|
* When a pulse on the SDA input has smaller width than this register value
|
|
* in I2C module clock cycles, the I2C controller will ignore that pulse.
|
|
*/
|
|
#define I2C_SDA_FILTER_THRES 0x0000000FU
|
|
#define I2C_SDA_FILTER_THRES_M (I2C_SDA_FILTER_THRES_V << I2C_SDA_FILTER_THRES_S)
|
|
#define I2C_SDA_FILTER_THRES_V 0x0000000FU
|
|
#define I2C_SDA_FILTER_THRES_S 4
|
|
/** I2C_SCL_FILTER_EN : R/W; bitpos: [8]; default: 1;
|
|
* This is the filter enable bit for SCL.
|
|
*/
|
|
#define I2C_SCL_FILTER_EN (BIT(8))
|
|
#define I2C_SCL_FILTER_EN_M (I2C_SCL_FILTER_EN_V << I2C_SCL_FILTER_EN_S)
|
|
#define I2C_SCL_FILTER_EN_V 0x00000001U
|
|
#define I2C_SCL_FILTER_EN_S 8
|
|
/** I2C_SDA_FILTER_EN : R/W; bitpos: [9]; default: 1;
|
|
* This is the filter enable bit for SDA.
|
|
*/
|
|
#define I2C_SDA_FILTER_EN (BIT(9))
|
|
#define I2C_SDA_FILTER_EN_M (I2C_SDA_FILTER_EN_V << I2C_SDA_FILTER_EN_S)
|
|
#define I2C_SDA_FILTER_EN_V 0x00000001U
|
|
#define I2C_SDA_FILTER_EN_S 9
|
|
|
|
/** I2C_CLK_CONF_REG register
|
|
* I2C CLK configuration register
|
|
*/
|
|
#define I2C_CLK_CONF_REG(i) (REG_I2C_BASE(i) + 0x54)
|
|
/** I2C_SCLK_DIV_NUM : R/W; bitpos: [7:0]; default: 0;
|
|
* the integral part of the fractional divisor for i2c module
|
|
*/
|
|
#define I2C_SCLK_DIV_NUM 0x000000FFU
|
|
#define I2C_SCLK_DIV_NUM_M (I2C_SCLK_DIV_NUM_V << I2C_SCLK_DIV_NUM_S)
|
|
#define I2C_SCLK_DIV_NUM_V 0x000000FFU
|
|
#define I2C_SCLK_DIV_NUM_S 0
|
|
/** I2C_SCLK_DIV_A : R/W; bitpos: [13:8]; default: 0;
|
|
* the numerator of the fractional part of the fractional divisor for i2c module
|
|
*/
|
|
#define I2C_SCLK_DIV_A 0x0000003FU
|
|
#define I2C_SCLK_DIV_A_M (I2C_SCLK_DIV_A_V << I2C_SCLK_DIV_A_S)
|
|
#define I2C_SCLK_DIV_A_V 0x0000003FU
|
|
#define I2C_SCLK_DIV_A_S 8
|
|
/** I2C_SCLK_DIV_B : R/W; bitpos: [19:14]; default: 0;
|
|
* the denominator of the fractional part of the fractional divisor for i2c module
|
|
*/
|
|
#define I2C_SCLK_DIV_B 0x0000003FU
|
|
#define I2C_SCLK_DIV_B_M (I2C_SCLK_DIV_B_V << I2C_SCLK_DIV_B_S)
|
|
#define I2C_SCLK_DIV_B_V 0x0000003FU
|
|
#define I2C_SCLK_DIV_B_S 14
|
|
/** I2C_SCLK_SEL : R/W; bitpos: [20]; default: 0;
|
|
* The clock selection for i2c module:0-XTAL,1-CLK_8MHz.
|
|
*/
|
|
#define I2C_SCLK_SEL (BIT(20))
|
|
#define I2C_SCLK_SEL_M (I2C_SCLK_SEL_V << I2C_SCLK_SEL_S)
|
|
#define I2C_SCLK_SEL_V 0x00000001U
|
|
#define I2C_SCLK_SEL_S 20
|
|
/** I2C_SCLK_ACTIVE : R/W; bitpos: [21]; default: 1;
|
|
* The clock switch for i2c module
|
|
*/
|
|
#define I2C_SCLK_ACTIVE (BIT(21))
|
|
#define I2C_SCLK_ACTIVE_M (I2C_SCLK_ACTIVE_V << I2C_SCLK_ACTIVE_S)
|
|
#define I2C_SCLK_ACTIVE_V 0x00000001U
|
|
#define I2C_SCLK_ACTIVE_S 21
|
|
|
|
/** I2C_COMD0_REG register
|
|
* I2C command register 0
|
|
*/
|
|
#define I2C_COMD0_REG(i) (REG_I2C_BASE(i) + 0x58)
|
|
/** I2C_COMMAND0 : R/W; bitpos: [13:0]; default: 0;
|
|
* This is the content of command 0. It consists of three parts:
|
|
* op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
|
|
* Byte_num represents the number of bytes that need to be sent or received.
|
|
* ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
|
|
* structure for more
|
|
* Information.
|
|
*/
|
|
#define I2C_COMMAND0 0x00003FFFU
|
|
#define I2C_COMMAND0_M (I2C_COMMAND0_V << I2C_COMMAND0_S)
|
|
#define I2C_COMMAND0_V 0x00003FFFU
|
|
#define I2C_COMMAND0_S 0
|
|
/** I2C_COMMAND0_DONE : R/W/SS; bitpos: [31]; default: 0;
|
|
* When command 0 is done in I2C Master mode, this bit changes to high
|
|
* level.
|
|
*/
|
|
#define I2C_COMMAND0_DONE (BIT(31))
|
|
#define I2C_COMMAND0_DONE_M (I2C_COMMAND0_DONE_V << I2C_COMMAND0_DONE_S)
|
|
#define I2C_COMMAND0_DONE_V 0x00000001U
|
|
#define I2C_COMMAND0_DONE_S 31
|
|
|
|
/** I2C_COMD1_REG register
|
|
* I2C command register 1
|
|
*/
|
|
#define I2C_COMD1_REG(i) (REG_I2C_BASE(i) + 0x5c)
|
|
/** I2C_COMMAND1 : R/W; bitpos: [13:0]; default: 0;
|
|
* This is the content of command 1. It consists of three parts:
|
|
* op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
|
|
* Byte_num represents the number of bytes that need to be sent or received.
|
|
* ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
|
|
* structure for more
|
|
* Information.
|
|
*/
|
|
#define I2C_COMMAND1 0x00003FFFU
|
|
#define I2C_COMMAND1_M (I2C_COMMAND1_V << I2C_COMMAND1_S)
|
|
#define I2C_COMMAND1_V 0x00003FFFU
|
|
#define I2C_COMMAND1_S 0
|
|
/** I2C_COMMAND1_DONE : R/W/SS; bitpos: [31]; default: 0;
|
|
* When command 1 is done in I2C Master mode, this bit changes to high
|
|
* level.
|
|
*/
|
|
#define I2C_COMMAND1_DONE (BIT(31))
|
|
#define I2C_COMMAND1_DONE_M (I2C_COMMAND1_DONE_V << I2C_COMMAND1_DONE_S)
|
|
#define I2C_COMMAND1_DONE_V 0x00000001U
|
|
#define I2C_COMMAND1_DONE_S 31
|
|
|
|
/** I2C_COMD2_REG register
|
|
* I2C command register 2
|
|
*/
|
|
#define I2C_COMD2_REG(i) (REG_I2C_BASE(i) + 0x60)
|
|
/** I2C_COMMAND2 : R/W; bitpos: [13:0]; default: 0;
|
|
* This is the content of command 2. It consists of three parts:
|
|
* op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
|
|
* Byte_num represents the number of bytes that need to be sent or received.
|
|
* ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
|
|
* structure for more
|
|
* Information.
|
|
*/
|
|
#define I2C_COMMAND2 0x00003FFFU
|
|
#define I2C_COMMAND2_M (I2C_COMMAND2_V << I2C_COMMAND2_S)
|
|
#define I2C_COMMAND2_V 0x00003FFFU
|
|
#define I2C_COMMAND2_S 0
|
|
/** I2C_COMMAND2_DONE : R/W/SS; bitpos: [31]; default: 0;
|
|
* When command 2 is done in I2C Master mode, this bit changes to high
|
|
* Level.
|
|
*/
|
|
#define I2C_COMMAND2_DONE (BIT(31))
|
|
#define I2C_COMMAND2_DONE_M (I2C_COMMAND2_DONE_V << I2C_COMMAND2_DONE_S)
|
|
#define I2C_COMMAND2_DONE_V 0x00000001U
|
|
#define I2C_COMMAND2_DONE_S 31
|
|
|
|
/** I2C_COMD3_REG register
|
|
* I2C command register 3
|
|
*/
|
|
#define I2C_COMD3_REG(i) (REG_I2C_BASE(i) + 0x64)
|
|
/** I2C_COMMAND3 : R/W; bitpos: [13:0]; default: 0;
|
|
* This is the content of command 3. It consists of three parts:
|
|
* op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
|
|
* Byte_num represents the number of bytes that need to be sent or received.
|
|
* ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
|
|
* structure for more
|
|
* Information.
|
|
*/
|
|
#define I2C_COMMAND3 0x00003FFFU
|
|
#define I2C_COMMAND3_M (I2C_COMMAND3_V << I2C_COMMAND3_S)
|
|
#define I2C_COMMAND3_V 0x00003FFFU
|
|
#define I2C_COMMAND3_S 0
|
|
/** I2C_COMMAND3_DONE : R/W/SS; bitpos: [31]; default: 0;
|
|
* When command 3 is done in I2C Master mode, this bit changes to high
|
|
* level.
|
|
*/
|
|
#define I2C_COMMAND3_DONE (BIT(31))
|
|
#define I2C_COMMAND3_DONE_M (I2C_COMMAND3_DONE_V << I2C_COMMAND3_DONE_S)
|
|
#define I2C_COMMAND3_DONE_V 0x00000001U
|
|
#define I2C_COMMAND3_DONE_S 31
|
|
|
|
/** I2C_COMD4_REG register
|
|
* I2C command register 4
|
|
*/
|
|
#define I2C_COMD4_REG(i) (REG_I2C_BASE(i) + 0x68)
|
|
/** I2C_COMMAND4 : R/W; bitpos: [13:0]; default: 0;
|
|
* This is the content of command 4. It consists of three parts:
|
|
* op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
|
|
* Byte_num represents the number of bytes that need to be sent or received.
|
|
* ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
|
|
* structure for more
|
|
* Information.
|
|
*/
|
|
#define I2C_COMMAND4 0x00003FFFU
|
|
#define I2C_COMMAND4_M (I2C_COMMAND4_V << I2C_COMMAND4_S)
|
|
#define I2C_COMMAND4_V 0x00003FFFU
|
|
#define I2C_COMMAND4_S 0
|
|
/** I2C_COMMAND4_DONE : R/W/SS; bitpos: [31]; default: 0;
|
|
* When command 4 is done in I2C Master mode, this bit changes to high
|
|
* level.
|
|
*/
|
|
#define I2C_COMMAND4_DONE (BIT(31))
|
|
#define I2C_COMMAND4_DONE_M (I2C_COMMAND4_DONE_V << I2C_COMMAND4_DONE_S)
|
|
#define I2C_COMMAND4_DONE_V 0x00000001U
|
|
#define I2C_COMMAND4_DONE_S 31
|
|
|
|
/** I2C_COMD5_REG register
|
|
* I2C command register 5
|
|
*/
|
|
#define I2C_COMD5_REG(i) (REG_I2C_BASE(i) + 0x6c)
|
|
/** I2C_COMMAND5 : R/W; bitpos: [13:0]; default: 0;
|
|
* This is the content of command 5. It consists of three parts:
|
|
* op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
|
|
* Byte_num represents the number of bytes that need to be sent or received.
|
|
* ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
|
|
* structure for more
|
|
* Information.
|
|
*/
|
|
#define I2C_COMMAND5 0x00003FFFU
|
|
#define I2C_COMMAND5_M (I2C_COMMAND5_V << I2C_COMMAND5_S)
|
|
#define I2C_COMMAND5_V 0x00003FFFU
|
|
#define I2C_COMMAND5_S 0
|
|
/** I2C_COMMAND5_DONE : R/W/SS; bitpos: [31]; default: 0;
|
|
* When command 5 is done in I2C Master mode, this bit changes to high level.
|
|
*/
|
|
#define I2C_COMMAND5_DONE (BIT(31))
|
|
#define I2C_COMMAND5_DONE_M (I2C_COMMAND5_DONE_V << I2C_COMMAND5_DONE_S)
|
|
#define I2C_COMMAND5_DONE_V 0x00000001U
|
|
#define I2C_COMMAND5_DONE_S 31
|
|
|
|
/** I2C_COMD6_REG register
|
|
* I2C command register 6
|
|
*/
|
|
#define I2C_COMD6_REG(i) (REG_I2C_BASE(i) + 0x70)
|
|
/** I2C_COMMAND6 : R/W; bitpos: [13:0]; default: 0;
|
|
* This is the content of command 6. It consists of three parts:
|
|
* op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
|
|
* Byte_num represents the number of bytes that need to be sent or received.
|
|
* ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
|
|
* structure for more
|
|
* Information.
|
|
*/
|
|
#define I2C_COMMAND6 0x00003FFFU
|
|
#define I2C_COMMAND6_M (I2C_COMMAND6_V << I2C_COMMAND6_S)
|
|
#define I2C_COMMAND6_V 0x00003FFFU
|
|
#define I2C_COMMAND6_S 0
|
|
/** I2C_COMMAND6_DONE : R/W/SS; bitpos: [31]; default: 0;
|
|
* When command 6 is done in I2C Master mode, this bit changes to high level.
|
|
*/
|
|
#define I2C_COMMAND6_DONE (BIT(31))
|
|
#define I2C_COMMAND6_DONE_M (I2C_COMMAND6_DONE_V << I2C_COMMAND6_DONE_S)
|
|
#define I2C_COMMAND6_DONE_V 0x00000001U
|
|
#define I2C_COMMAND6_DONE_S 31
|
|
|
|
/** I2C_COMD7_REG register
|
|
* I2C command register 7
|
|
*/
|
|
#define I2C_COMD7_REG(i) (REG_I2C_BASE(i) + 0x74)
|
|
/** I2C_COMMAND7 : R/W; bitpos: [13:0]; default: 0;
|
|
* This is the content of command 7. It consists of three parts:
|
|
* op_code is the command, 0: RSTART, 1: WRITE, 2: READ, 3: STOP, 4: END.
|
|
* Byte_num represents the number of bytes that need to be sent or received.
|
|
* ack_check_en, ack_exp and ack are used to control the ACK bit. See I2C cmd
|
|
* structure for more
|
|
* Information.
|
|
*/
|
|
#define I2C_COMMAND7 0x00003FFFU
|
|
#define I2C_COMMAND7_M (I2C_COMMAND7_V << I2C_COMMAND7_S)
|
|
#define I2C_COMMAND7_V 0x00003FFFU
|
|
#define I2C_COMMAND7_S 0
|
|
/** I2C_COMMAND7_DONE : R/W/SS; bitpos: [31]; default: 0;
|
|
* When command 7 is done in I2C Master mode, this bit changes to high level.
|
|
*/
|
|
#define I2C_COMMAND7_DONE (BIT(31))
|
|
#define I2C_COMMAND7_DONE_M (I2C_COMMAND7_DONE_V << I2C_COMMAND7_DONE_S)
|
|
#define I2C_COMMAND7_DONE_V 0x00000001U
|
|
#define I2C_COMMAND7_DONE_S 31
|
|
|
|
/** I2C_SCL_ST_TIME_OUT_REG register
|
|
* SCL status time out register
|
|
*/
|
|
#define I2C_SCL_ST_TIME_OUT_REG(i) (REG_I2C_BASE(i) + 0x78)
|
|
/** I2C_SCL_ST_TO_I2C : R/W; bitpos: [4:0]; default: 16;
|
|
* The threshold value of SCL_FSM state unchanged period. It should be o more than 23
|
|
*/
|
|
#define I2C_SCL_ST_TO_I2C 0x0000001FU
|
|
#define I2C_SCL_ST_TO_I2C_M (I2C_SCL_ST_TO_I2C_V << I2C_SCL_ST_TO_I2C_S)
|
|
#define I2C_SCL_ST_TO_I2C_V 0x0000001FU
|
|
#define I2C_SCL_ST_TO_I2C_S 0
|
|
|
|
/** I2C_SCL_MAIN_ST_TIME_OUT_REG register
|
|
* SCL main status time out register
|
|
*/
|
|
#define I2C_SCL_MAIN_ST_TIME_OUT_REG(i) (REG_I2C_BASE(i) + 0x7c)
|
|
/** I2C_SCL_MAIN_ST_TO_I2C : R/W; bitpos: [4:0]; default: 16;
|
|
* The threshold value of SCL_MAIN_FSM state unchanged period.nIt should be o more
|
|
* than 23
|
|
*/
|
|
#define I2C_SCL_MAIN_ST_TO_I2C 0x0000001FU
|
|
#define I2C_SCL_MAIN_ST_TO_I2C_M (I2C_SCL_MAIN_ST_TO_I2C_V << I2C_SCL_MAIN_ST_TO_I2C_S)
|
|
#define I2C_SCL_MAIN_ST_TO_I2C_V 0x0000001FU
|
|
#define I2C_SCL_MAIN_ST_TO_I2C_S 0
|
|
|
|
/** I2C_SCL_SP_CONF_REG register
|
|
* Power configuration register
|
|
*/
|
|
#define I2C_SCL_SP_CONF_REG(i) (REG_I2C_BASE(i) + 0x80)
|
|
/** I2C_SCL_RST_SLV_EN : R/W/SC; bitpos: [0]; default: 0;
|
|
* When I2C master is IDLE, set this bit to send out SCL pulses. The number of pulses
|
|
* equals to reg_scl_rst_slv_num[4:0].
|
|
*/
|
|
#define I2C_SCL_RST_SLV_EN (BIT(0))
|
|
#define I2C_SCL_RST_SLV_EN_M (I2C_SCL_RST_SLV_EN_V << I2C_SCL_RST_SLV_EN_S)
|
|
#define I2C_SCL_RST_SLV_EN_V 0x00000001U
|
|
#define I2C_SCL_RST_SLV_EN_S 0
|
|
/** I2C_SCL_RST_SLV_NUM : R/W; bitpos: [5:1]; default: 0;
|
|
* Configure the pulses of SCL generated in I2C master mode. Valid when
|
|
* reg_scl_rst_slv_en is 1.
|
|
*/
|
|
#define I2C_SCL_RST_SLV_NUM 0x0000001FU
|
|
#define I2C_SCL_RST_SLV_NUM_M (I2C_SCL_RST_SLV_NUM_V << I2C_SCL_RST_SLV_NUM_S)
|
|
#define I2C_SCL_RST_SLV_NUM_V 0x0000001FU
|
|
#define I2C_SCL_RST_SLV_NUM_S 1
|
|
/** I2C_SCL_PD_EN : R/W; bitpos: [6]; default: 0;
|
|
* The power down enable bit for the I2C output SCL line. 1: Power down. 0: Not power
|
|
* down. Set reg_scl_force_out and reg_scl_pd_en to 1 to stretch SCL low.
|
|
*/
|
|
#define I2C_SCL_PD_EN (BIT(6))
|
|
#define I2C_SCL_PD_EN_M (I2C_SCL_PD_EN_V << I2C_SCL_PD_EN_S)
|
|
#define I2C_SCL_PD_EN_V 0x00000001U
|
|
#define I2C_SCL_PD_EN_S 6
|
|
/** I2C_SDA_PD_EN : R/W; bitpos: [7]; default: 0;
|
|
* The power down enable bit for the I2C output SDA line. 1: Power down. 0: Not power
|
|
* down. Set reg_sda_force_out and reg_sda_pd_en to 1 to stretch SDA low.
|
|
*/
|
|
#define I2C_SDA_PD_EN (BIT(7))
|
|
#define I2C_SDA_PD_EN_M (I2C_SDA_PD_EN_V << I2C_SDA_PD_EN_S)
|
|
#define I2C_SDA_PD_EN_V 0x00000001U
|
|
#define I2C_SDA_PD_EN_S 7
|
|
|
|
/** I2C_SCL_STRETCH_CONF_REG register
|
|
* Set SCL stretch of I2C slave
|
|
*/
|
|
#define I2C_SCL_STRETCH_CONF_REG(i) (REG_I2C_BASE(i) + 0x84)
|
|
/** I2C_STRETCH_PROTECT_NUM : R/W; bitpos: [9:0]; default: 0;
|
|
* Configure the period of I2C slave stretching SCL line.
|
|
*/
|
|
#define I2C_STRETCH_PROTECT_NUM 0x000003FFU
|
|
#define I2C_STRETCH_PROTECT_NUM_M (I2C_STRETCH_PROTECT_NUM_V << I2C_STRETCH_PROTECT_NUM_S)
|
|
#define I2C_STRETCH_PROTECT_NUM_V 0x000003FFU
|
|
#define I2C_STRETCH_PROTECT_NUM_S 0
|
|
/** I2C_SLAVE_SCL_STRETCH_EN : R/W; bitpos: [10]; default: 0;
|
|
* The enable bit for slave SCL stretch function. 1: Enable. 0: Disable. The SCL
|
|
* output line will be stretched low when reg_slave_scl_stretch_en is 1 and stretch
|
|
* event happens. The stretch cause can be seen in reg_stretch_cause.
|
|
*/
|
|
#define I2C_SLAVE_SCL_STRETCH_EN (BIT(10))
|
|
#define I2C_SLAVE_SCL_STRETCH_EN_M (I2C_SLAVE_SCL_STRETCH_EN_V << I2C_SLAVE_SCL_STRETCH_EN_S)
|
|
#define I2C_SLAVE_SCL_STRETCH_EN_V 0x00000001U
|
|
#define I2C_SLAVE_SCL_STRETCH_EN_S 10
|
|
/** I2C_SLAVE_SCL_STRETCH_CLR : WT; bitpos: [11]; default: 0;
|
|
* Set this bit to clear the I2C slave SCL stretch function.
|
|
*/
|
|
#define I2C_SLAVE_SCL_STRETCH_CLR (BIT(11))
|
|
#define I2C_SLAVE_SCL_STRETCH_CLR_M (I2C_SLAVE_SCL_STRETCH_CLR_V << I2C_SLAVE_SCL_STRETCH_CLR_S)
|
|
#define I2C_SLAVE_SCL_STRETCH_CLR_V 0x00000001U
|
|
#define I2C_SLAVE_SCL_STRETCH_CLR_S 11
|
|
/** I2C_SLAVE_BYTE_ACK_CTL_EN : R/W; bitpos: [12]; default: 0;
|
|
* The enable bit for slave to control ACK level function.
|
|
*/
|
|
#define I2C_SLAVE_BYTE_ACK_CTL_EN (BIT(12))
|
|
#define I2C_SLAVE_BYTE_ACK_CTL_EN_M (I2C_SLAVE_BYTE_ACK_CTL_EN_V << I2C_SLAVE_BYTE_ACK_CTL_EN_S)
|
|
#define I2C_SLAVE_BYTE_ACK_CTL_EN_V 0x00000001U
|
|
#define I2C_SLAVE_BYTE_ACK_CTL_EN_S 12
|
|
/** I2C_SLAVE_BYTE_ACK_LVL : R/W; bitpos: [13]; default: 0;
|
|
* Set the ACK level when slave controlling ACK level function enables.
|
|
*/
|
|
#define I2C_SLAVE_BYTE_ACK_LVL (BIT(13))
|
|
#define I2C_SLAVE_BYTE_ACK_LVL_M (I2C_SLAVE_BYTE_ACK_LVL_V << I2C_SLAVE_BYTE_ACK_LVL_S)
|
|
#define I2C_SLAVE_BYTE_ACK_LVL_V 0x00000001U
|
|
#define I2C_SLAVE_BYTE_ACK_LVL_S 13
|
|
|
|
/** I2C_DATE_REG register
|
|
* Version register
|
|
*/
|
|
#define I2C_DATE_REG(i) (REG_I2C_BASE(i) + 0xf8)
|
|
/** I2C_DATE : R/W; bitpos: [31:0]; default: 35656050;
|
|
* This is the the version register.
|
|
*/
|
|
#define I2C_DATE 0xFFFFFFFFU
|
|
#define I2C_DATE_M (I2C_DATE_V << I2C_DATE_S)
|
|
#define I2C_DATE_V 0xFFFFFFFFU
|
|
#define I2C_DATE_S 0
|
|
|
|
/** I2C_TXFIFO_START_ADDR_REG register
|
|
* I2C TXFIFO base address register
|
|
*/
|
|
#define I2C_TXFIFO_START_ADDR_REG(i) (REG_I2C_BASE(i) + 0x100)
|
|
/** I2C_TXFIFO_START_ADDR : HRO; bitpos: [31:0]; default: 0;
|
|
* This is the I2C txfifo first address.
|
|
*/
|
|
#define I2C_TXFIFO_START_ADDR 0xFFFFFFFFU
|
|
#define I2C_TXFIFO_START_ADDR_M (I2C_TXFIFO_START_ADDR_V << I2C_TXFIFO_START_ADDR_S)
|
|
#define I2C_TXFIFO_START_ADDR_V 0xFFFFFFFFU
|
|
#define I2C_TXFIFO_START_ADDR_S 0
|
|
|
|
/** I2C_RXFIFO_START_ADDR_REG register
|
|
* I2C RXFIFO base address register
|
|
*/
|
|
#define I2C_RXFIFO_START_ADDR_REG(i) (REG_I2C_BASE(i) + 0x180)
|
|
/** I2C_RXFIFO_START_ADDR : HRO; bitpos: [31:0]; default: 0;
|
|
* This is the I2C rxfifo first address.
|
|
*/
|
|
#define I2C_RXFIFO_START_ADDR 0xFFFFFFFFU
|
|
#define I2C_RXFIFO_START_ADDR_M (I2C_RXFIFO_START_ADDR_V << I2C_RXFIFO_START_ADDR_S)
|
|
#define I2C_RXFIFO_START_ADDR_V 0xFFFFFFFFU
|
|
#define I2C_RXFIFO_START_ADDR_S 0
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|