mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
80 lines
3.8 KiB
Markdown
80 lines
3.8 KiB
Markdown
| Supported Targets | ESP32-S2 |
|
|
| ----------------- | -------- |
|
|
|
|
# Matrix Keyboard Example (based on Dedicated GPIO)
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
## Overview
|
|
|
|
This example mainly illustrates how to drive a common matrix keyboard using the dedicated GPIO APIs, including:
|
|
|
|
* Manipulate the level on a group of GPIOs
|
|
* Trigger edge interrupt
|
|
* Read level on a group of GPIOs
|
|
|
|
Dedicated GPIO is designed to speed up CPU operations on one or a group of GPIOs by writing assembly codes with Espressif customized instructions (please refer TRM to get more information about these instructions).
|
|
|
|
This matrix keyboard driver is interrupt-driven, supports a configurable debounce time. GPIOs used by row and column lines are also configurable during driver installation stage.
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
This example can run on any target that has the dedicated feature (e.g. ESP32-S2). It's not necessary for your matrix board to have pull-up resisters on row/column lines. The driver has enabled internal pull-up resister by default. A typical matrix board should look as follows:
|
|
|
|
```
|
|
row_0 +--------+-------------------+------------------------------+-----------------+
|
|
| | |
|
|
| + | + | +
|
|
| +-+-+ | +-+-+ ...... | +-+-+
|
|
. +-----+ +-----+ +-----+ +-----+ +-----+ +-----+
|
|
. | | |
|
|
. . | . | . |
|
|
. | . | ...... . |
|
|
. | . | . |
|
|
. | . | . |
|
|
| | |
|
|
row_n +--------+-------------------+------------------------------+-----------------+
|
|
| | | | | |
|
|
| + | | + | | + |
|
|
| +-+-+ | | +-+-+ | ...... | +-+-+ |
|
|
+-----+ +-----+ +-----+ +-----+ +-----+ +-----+
|
|
| | |
|
|
| | |
|
|
| | |
|
|
+ + +
|
|
col_0 col_1 ...... col_m
|
|
```
|
|
|
|
### Build and Flash
|
|
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```
|
|
idf.py -p PORT flash monitor
|
|
```
|
|
|
|
(Replace PORT with the name of the serial port to use.)
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
```
|
|
I (2883) example: press event, key code = 0002
|
|
I (3003) example: release event, key code = 0002
|
|
I (5053) example: press event, key code = 0001
|
|
I (5203) example: release event, key code = 0001
|
|
I (6413) example: press event, key code = 0000
|
|
I (6583) example: release event, key code = 0000
|
|
I (7963) example: press event, key code = 0003
|
|
I (8113) example: release event, key code = 0003
|
|
I (8773) example: press event, key code = 0103
|
|
I (8923) example: release event, key code = 0103
|
|
I (9543) example: press event, key code = 0203
|
|
I (9683) example: release event, key code = 0203
|
|
```
|