mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
252 lines
8.3 KiB
Markdown
252 lines
8.3 KiB
Markdown
| Supported Targets | ESP32 | ESP32-C3 | ESP32-S2 | ESP32-S3 |
|
|
| ----------------- | ----- | -------- | -------- | -------- |
|
|
|
|
# OpenThread Border Router Example
|
|
|
|
## Overview
|
|
|
|
This example demonstrates an [OpenThread border router](https://openthread.io/guides/border-router).
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
The following SoCs are required to run this example:
|
|
* An ESP32 series Wi-Fi SoC (ESP32, ESP32-C, ESP32-S, etc) loaded with this ot_br example.
|
|
* An ESP32-H2 802.15.4 SoC loaded with [ot_rcp](../ot_rcp) example.
|
|
* Another ESP32-H2 SoC loaded with [ot_cli](../ot_cli) example. Enable `OPENTHREAD_JOINER` option in menuconfig before compiling the example.
|
|
|
|
Connect the two SoCs via UART, below is an example setup with ESP32 DevKitC and ESP32-H2 DevKitC:
|
|
|
|
|
|
ESP32 pin | ESP32-H2 pin
|
|
----------|-------------
|
|
GND | G
|
|
GPIO4 | TX
|
|
GPIO5 | RX
|
|
|
|
### Configure the project
|
|
|
|
```
|
|
idf.py menuconfig
|
|
```
|
|
Two ways are provided to setup the Thread Border Router in this example:
|
|
|
|
- Auto Start
|
|
Enable `OPENTHREAD_BR_AUTO_START`, configure the `CONFIG_EXAMPLE_WIFI_SSID` and `CONFIG_EXAMPLE_WIFI_PASSWORD` with your access point's ssid and psk.
|
|
The device will connect to Wi-Fi and form a Thread network automatically after bootup.
|
|
|
|
- Manual mode
|
|
Disable `OPENTHREAD_BR_AUTO_START` and enable `OPENTHREAD_CLI_ESP_EXTENSION`. `wifi` command will be added for connecting the device to the Wi-Fi network.
|
|
|
|
### Build, Flash, and Run
|
|
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```
|
|
idf.py -p PORT build flash monitor
|
|
```
|
|
If the `OPENTHREAD_BR_AUTO_START` option is enabled, The device will be connected to the configured Wi-Fi and Thread network automatically then act as the border router.
|
|
|
|
Otherwise, you need to manually configure the networks with CLI commands.
|
|
|
|
`wifi` command can be used to configure the Wi-Fi network.
|
|
|
|
```bash
|
|
> wifi
|
|
--wifi parameter---
|
|
connect
|
|
-s : wifi ssid
|
|
-p : wifi psk
|
|
---example---
|
|
join a wifi:
|
|
ssid: threadcertAP
|
|
psk: threadcertAP : wifi connect -s threadcertAP -p threadcertAP
|
|
state : get wifi state, disconnect or connect
|
|
---example---
|
|
get wifi state : wifi state
|
|
Done
|
|
```
|
|
|
|
To join a Wi-Fi network, please use the `wifi connect` command:
|
|
|
|
```bash
|
|
> wifi connect -s threadcertAP -p threadcertAP
|
|
ssid: threadcertAP
|
|
psk: threadcertAP
|
|
I (11331) wifi:wifi driver task: 3ffd06e4, prio:23, stack:6656, core=0
|
|
I (11331) system_api: Base MAC address is not set
|
|
I (11331) system_api: read default base MAC address from EFUSE
|
|
I (11341) wifi:wifi firmware version: 45c46a4
|
|
I (11341) wifi:wifi certification version: v7.0
|
|
|
|
|
|
..........
|
|
|
|
I (13741) esp_netif_handlers: sta ip: 192.168.3.10, mask: 255.255.255.0, gw: 192.168.3.1
|
|
W (13771) wifi:<ba-add>idx:0 (ifx:0, 02:0f:c1:32:3b:2b), tid:0, ssn:2, winSize:64
|
|
wifi sta is connected successfully
|
|
Done
|
|
```
|
|
|
|
To get the state of the Wi-Fi network:
|
|
|
|
```bash
|
|
> wifi state
|
|
connected
|
|
Done
|
|
```
|
|
|
|
For forming the Thread network, please refer to the [ot_cli_README](../ot_cli/README.md).
|
|
|
|
## Example Output
|
|
|
|
```bash
|
|
I (2729) esp_netif_handlers: example_connect: sta ip: 192.168.1.100, mask: 255.255.255.0, gw: 192.168.1.1
|
|
I (2729) example_connect: Got IPv4 event: Interface "example_connect: sta" address: 192.168.1.100
|
|
I (3729) example_connect: Got IPv6 event: Interface "example_connect: sta" address: fe80:0000:0000:0000:266f:28ff:fe80:2920, type: ESP_IP6_ADDR_IS_LINK_LOCAL
|
|
I (3729) example_connect: Connected to example_connect: sta
|
|
I (3739) example_connect: - IPv4 address: 192.168.1.100
|
|
I (3739) example_connect: - IPv6 address: fe80:0000:0000:0000:266f:28ff:fe80:2920, type: ESP_IP6_ADDR_IS_LINK_LOCAL
|
|
|
|
......
|
|
|
|
|
|
I(8139) OPENTHREAD:[INFO]-MLE-----: AttachState ParentReqReeds -> Idle
|
|
I(8139) OPENTHREAD:[NOTE]-MLE-----: Allocate router id 50
|
|
I(8139) OPENTHREAD:[NOTE]-MLE-----: RLOC16 fffe -> c800
|
|
I(8159) OPENTHREAD:[NOTE]-MLE-----: Role Detached -> Leader
|
|
```
|
|
|
|
## Bidirectional IPv6 connectivity
|
|
|
|
The border router will automatically publish the prefix and the route table rule to the Wi-Fi network via ICMPv6 router advertisement packages.
|
|
|
|
### Host configuration
|
|
|
|
The automatically configure your host's route table rules you need to set these sysctl options:
|
|
|
|
Please replace `wlan0` with the real name of your Wi-Fi network interface.
|
|
```
|
|
sudo sysctl -w net/ipv6/conf/wlan0/accept_ra=2
|
|
sudo sysctl -w net/ipv6/conf/wlan0/accept_ra_rt_info_max_plen=128
|
|
```
|
|
|
|
For mobile devices, the route table rules will be automatically configured after iOS 14 and Android 8.1.
|
|
|
|
|
|
### Testing IPv6 connectivity
|
|
|
|
Now in the Thread end device, check the IP addresses:
|
|
|
|
```
|
|
> ipaddr
|
|
fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
|
|
fdde:ad00:beef:0:0:ff:fe00:c402
|
|
fdde:ad00:beef:0:ad4a:9a9a:3cd6:e423
|
|
fe80:0:0:0:f011:2951:569e:9c4a
|
|
```
|
|
|
|
You'll notice an IPv6 global prefix with only on address assigned under it. This is the routable address of this Thread node.
|
|
You can ping this address on your host:
|
|
|
|
``` bash
|
|
$ ping fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
|
|
PING fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5(fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5) 56 data bytes
|
|
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=1 ttl=63 time=459 ms
|
|
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=2 ttl=63 time=109 ms
|
|
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=3 ttl=63 time=119 ms
|
|
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=4 ttl=63 time=117 ms
|
|
```
|
|
|
|
## Service discovery
|
|
|
|
The newly introduced service registration protocol([SRP](https://datatracker.ietf.org/doc/html/draft-ietf-dnssd-srp-10)) allows devices in the Thread network to register a service. The border router will forward the service to the Wi-Fi network via mDNS.
|
|
|
|
### Publish the service using SRP
|
|
Now we'll publish the service `my-service._test._udp` with hostname `test0` and port 12345
|
|
|
|
```
|
|
> srp client host name test0
|
|
Done
|
|
> srp client host address fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
|
|
Done
|
|
> srp client service add my-service _test._udp 12345
|
|
Done
|
|
> srp client autostart enable
|
|
Done
|
|
```
|
|
|
|
This service will also become visible on the Wi-Fi network:
|
|
|
|
```bash
|
|
$ avahi-browse -r _test._udp -t
|
|
|
|
+ enp1s0 IPv6 my-service _test._udp local
|
|
= enp1s0 IPv6 my-service _test._udp local
|
|
hostname = [test0.local]
|
|
address = [fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5]
|
|
port = [12345]
|
|
txt = []
|
|
+ enp1s0 IPv4 my-service _test._udp local
|
|
= enp1s0 IPv4 my-service _test._udp local
|
|
hostname = [test0.local]
|
|
address = [fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5]
|
|
port = [12345]
|
|
txt = []
|
|
```
|
|
|
|
### Discovery delegate
|
|
|
|
First, the service `testhost._test._udp` need to be published using `avahi-publish-service` on the Wi-Fi network(for example Host).
|
|
|
|
```bash
|
|
$ avahi-publish-service testhost _test._udp 12345 test=1 dn="aabbbb"
|
|
```
|
|
|
|
Then get the border router's OMR prefix global unicast address(or ML-EID), and configure it on the Thread end device.
|
|
|
|
On the border router:
|
|
```
|
|
> ipaddr
|
|
fdde:ad00:beef:0:0:ff:fe00:fc10
|
|
fd9b:347f:93f7:1:1003:8f00:bcc1:3038
|
|
fdde:ad00:beef:0:0:ff:fe00:fc00
|
|
fdde:ad00:beef:0:0:ff:fe00:b800
|
|
fdde:ad00:beef:0:f891:287:866:776
|
|
fe80:0:0:0:77:bca6:6079:785b
|
|
Done
|
|
```
|
|
|
|
On the Thread end device:
|
|
```
|
|
> dns config fd9b:347f:93f7:1:1003:8f00:bcc1:3038
|
|
(or
|
|
> dns config fdde:ad00:beef:0:f891:287:866:776)
|
|
Done
|
|
```
|
|
|
|
Now the service published on the Host can be discovered on the Thread end device.
|
|
```
|
|
> dns resolve FA001208.default.service.arpa.
|
|
DNS response for FA001208.default.service.arpa. - fdde:ad00:beef:cafe:b939:26be:7516:b87e TTL:120
|
|
Done
|
|
|
|
> dns browse _test._udp.default.service.arpa.
|
|
DNS browse response for _test._udp.default.service.arpa.
|
|
testhost
|
|
Port:5683, Priority:0, Weight:0, TTL:120
|
|
Host:FA001208.default.service.arpa.
|
|
HostAddress:fdde:ad00:beef:cafe:b939:26be:7516:b87e TTL:120
|
|
TXT:[test=31, dn=616162626262] TTL:120
|
|
Done
|
|
|
|
> dns service testhost _test._udp.default.service.arpa.
|
|
DNS service resolution response for testhost for service _test._udp.default.service.arpa.
|
|
Port:5683, Priority:0, Weight:0, TTL:120
|
|
Host:FA001208.default.service.arpa.
|
|
HostAddress:fdde:ad00:beef:cafe:b939:26be:7516:b87e TTL:120
|
|
TXT:[test=31, dn=616162626262] TTL:120
|
|
Done
|
|
```
|