mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
91 lines
3.4 KiB
Markdown
91 lines
3.4 KiB
Markdown
# Example: GPIO
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This test code shows how to configure GPIO and how to use it with interruption.
|
|
|
|
## GPIO functions:
|
|
|
|
| GPIO | Direction | Configuration |
|
|
| ---------------------------- | --------- | ------------------------------------------------------ |
|
|
| CONFIG_GPIO_OUTPUT_0 | output | |
|
|
| CONFIG_GPIO_OUTPUT_1 | output | |
|
|
| CONFIG_GPIO_INPUT_0 | input | pulled up, interrupt from rising edge and falling edge |
|
|
| CONFIG_GPIO_INPUT_1 | input | pulled up, interrupt from rising edge |
|
|
|
|
## Test:
|
|
1. Connect CONFIG_GPIO_OUTPUT_0 with CONFIG_GPIO_INPUT_0
|
|
2. Connect CONFIG_GPIO_OUTPUT_1 with CONFIG_GPIO_INPUT_1
|
|
3. Generate pulses on CONFIG_GPIO_OUTPUT_0/1, that triggers interrupt on CONFIG_GPIO_INPUT_0/1
|
|
|
|
**Note:** The following pin assignments are used by default, you can change them by `idf.py menuconfig` > `Example Configuration`.
|
|
|
|
| | CONFIG_GPIO_OUTPUT_0 | CONFIG_GPIO_OUTPUT_1 | CONFIG_GPIO_INPUT_0 | CONFIG_GPIO_INPUT_1 |
|
|
| --------------- | -------------------- | -------------------- | ------------------- | ------------------- |
|
|
| ESP8684/ESP32H2 | 8 | 9 | 4 | 5 |
|
|
| All other chips | 18 | 19 | 4 | 5 |
|
|
|
|
## How to use example
|
|
|
|
Before project configuration and build, be sure to set the correct chip target using `idf.py set-target <chip_name>`.
|
|
|
|
### Hardware Required
|
|
|
|
* A development board with with any Espressif SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
|
|
* A USB cable for Power supply and programming
|
|
* Some jumper wires to connect GPIOs.
|
|
|
|
### Configure the project
|
|
|
|
### Build and Flash
|
|
|
|
Build the project and flash it to the board, then run the monitor tool to view the serial output:
|
|
|
|
Run `idf.py -p PORT flash monitor` to build, flash and monitor the project.
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
As you run the example, you will see the following log:
|
|
|
|
```
|
|
I (317) gpio: GPIO[18]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
|
|
I (327) gpio: GPIO[19]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
|
|
I (337) gpio: GPIO[4]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:1
|
|
I (347) gpio: GPIO[5]| InputEn: 1| OutputEn: 0| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:1
|
|
Minimum free heap size: 289892 bytes
|
|
cnt: 0
|
|
cnt: 1
|
|
GPIO[4] intr, val: 1
|
|
GPIO[5] intr, val: 1
|
|
cnt: 2
|
|
GPIO[4] intr, val: 0
|
|
cnt: 3
|
|
GPIO[4] intr, val: 1
|
|
GPIO[5] intr, val: 1
|
|
cnt: 4
|
|
GPIO[4] intr, val: 0
|
|
cnt: 5
|
|
GPIO[4] intr, val: 1
|
|
GPIO[5] intr, val: 1
|
|
cnt: 6
|
|
GPIO[4] intr, val: 0
|
|
cnt: 7
|
|
GPIO[4] intr, val: 1
|
|
GPIO[5] intr, val: 1
|
|
cnt: 8
|
|
GPIO[4] intr, val: 0
|
|
cnt: 9
|
|
GPIO[4] intr, val: 1
|
|
GPIO[5] intr, val: 1
|
|
cnt: 10
|
|
...
|
|
```
|
|
|
|
## Troubleshooting
|
|
|
|
For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|