When splitting a memory block, check if the next block is free.
If it is, then just extend it upwards instead of creating a new block.
This fixes a bug where when shrinking existing allocations would result in irreversible free space fragmentation.
When testing on the host, test all the poisoning configurations.
SDSPI driver optimized polling of the response tokens by requesting
two extra bytes on top of the block size (512) and CRC (2), and
checking whether these bytes contained the data response token or
not. In case the token was there, further polling would not need to
happen, thereby reducing latency between two consecutive blocks
transferred. However this caused compatibility issues when these two
extra bytes were sent after reading the final block. When
STOP_TRANSMISSION command was sent, these extra two bytes were
treated as part of the command, causing an invalid command error.
This fixes the logic by only requesting extra two bytes if the block
being read is not the final block. In addition to that, more strict
error checking is implemented for command response tokens.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references and address esp_sleep_wakeup_cause_t type.
The get_time_ms() is updated to explicitly use fabs(dt) instead of abs(dt) in test_sleep.c.
Some other minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
Some application lock interrupt(portENTER_CRITICAL) too long time,
it will cause bluetooth cannot react interrupt in time, then t will
cause some assert, assert info following:
1. ld_acl.c 1900
2. ld_fm.c 340
3. other assert reference to this.
It is not possible to generate 1 MHz REF_TICK from 2 MHz APB clock
(this is a limitation of REF_TICK divider circuit). Since switching
REF_TICK frequency is something we would like to avoid (to maintain
UART output even with DFS), 2 MHz frequency has been marked as
unsupported.
The issue would manifest itself in cases when switching from PM
configuration like {active=160MHz, idle=80MHz} to {active=80MHz,
idle=80Mhz}. After the configuration was changed, PM logic would
think that current frequency was 80MHz and would not do any further
switching. In fact, frequency was still 160MHz.
The old code calculated MAX() of two enum values, but CPU frequency
enum values are not ordered (2MHz goes after 240MHz). This caused
incorrect configuration to be set.
Previous code contained a check for PLL frequency to be 240MHz, while
in fact 240MHz was a CPU frequency; corresponding PLL frequency is
480MHz. Fixed the comparison and replaced integer MHz values with an
enum.
This commit adds character encoding configurations in for the fatfs component.
The FF_LFN_UNICODE definition in ffconf.h can now be changed to accept UTF-8 or
UTF-16 encoded filernames. Test cases using UTF-8 encoded file paths and names in
FatFs have also been added.
Closes#1183
1. External 32kHz crystal is started for too long or it may not start at all. It is often observed at the first start.
2. At the first start, it is possible that the crystal did not start. And the recorded period was recorded as 0. Which led to a division error by zero during the transition to the deep sleep mode (Maybe somewhere else).
3. Added a unit test to test a new method of oscillation an external crystal.
4. Added a new method of oscillating of an external crystal. The legs of the crystal are fed with a 32 kHz frequency.
The new method eliminates these errors.
Added unit test: `\esp-idf\components\soc\esp32\test\test_rtc_clk.c`: `make TEST_COMPONENTS=soc`
- 8 Test starting external RTC crystal. Will pass.
`Bootstrap cycles for external 32kHz crystal` - is specified in the file Kconfig by default 100.
QA tested a new method of oscillation the crystal on 25 boards. The supply of square waves on the crystal showed a 100% result in contrast to the previous method of launching the crystal. After the tests, the old method was deleted.
Closes TW19143
The expected usage is:
esp_pthread_set_cfg(cfg);
pthread_create()
If the inherit flag is set, then all subsequent threads forked by this
thread will also inherit this configuration. This avoids having to
change/prefix this for each and every pthread_create() call.
Component/bt: fix reconnect fail in smp for v3.0
See merge request idf/esp-idf!2075
(cherry picked from commit 7f2a9f0359)
d0e55335 Component/bt: fix reconnect fail in smp
The fast path of CPU frequency switch function, used in DFS, was not
waiting for the frequency switch to complete when switching from XTAL
to PLL. This resulted in incorrect reads from peripherals on APB,
where two consecutive reads could return the same value. For example,
in esp_timer, read of FRC_COUNT_REG would return same value as the
preceding read of FRC_ALARM_REG, causing time to jump by the value of
FRC_ALARM_REG / apb_freq_mhz.
- separate mode stats from lock stats by an extra comment line
- add CPU frequency column to the mode stats
- don’t print a row for light sleep if light sleep is not enabled
s_cpu_freq_by_mode array was statically initialised with 80MHz CPU
frequency in CPU_MAX and APB_MAX modes, but sdkconfig setting for the
CPU frequency could have been different. For the case of 240MHz CPU
frequency, this would cause a frequency switch between 240MHz and
80MHz to happen, even though such switch is not supported in the fast
path switching functions used by the DFS implementation.
This fixes the issue by moving initialisation into esp_pm_impl_init,
which is called at startup before the first mode switch can happen.
Fixes https://github.com/espressif/esp-idf/issues/1729.
The files updated according to code review discussions.
In the sleep_modes.c removed immidiate disable of ULP mode and leave just trigger deactivation.
The esp_sleep.h is updated to have the same defines for source as esp_sleep_wakeup_cause_t.
Updated documentation in sleep_modes.rst file to include cross references.
Some minor changes in test_sleep.c unit test.
(TW#18952)
Closes https://github.com/espressif/esp-idf/issues/1677
