SPI flash operations lock for shorter periods
Based on bug report here:
https://esp32.com/viewtopic.php?f=13&t=1489&p=6816#p6773
Long SPI flash erase (and possibly write/read) cycles block all tasks on both CPUs for an extended period, and can lead to WiFi dissassociation (and general priority inversion.)
This MR inserts preemption breaks into large operations (all erases, writes every 8KB, reads every 16KB).
Overhead of a single spi_flash_guart_start()/spi_flash_guard_end() cycle measured at approx 67us (assuming no preemption.)
See merge request !600
bugfix: ESP32 Core Dump reported issues
This MR fixes the following issues:
1. fixed path to esptool when there is no compiled python module for it
2. GDB inernal failure handling was added
See merge request !599
Error handling in NVS initialization
Previously nvs_flash_init worked under an assumption that there should always be at least one free page available. This is true during normal operation, but in some cases (such as when changing application partition table from a non-OTA to an OTA one), NVS partition may get truncated, which will cause empty pages to be lost.
This MR adds error checks for this condition, and updates code which calls `nvs_flash_init` to check for the return code.
For most examples, a simple `ESP_ERROR_CHECK` is added around `nvs_flash_init`. For NVS examples and the OTA example, more robust error handling is added.
This change also removes nvs_flash_init calls from examples which don't use NVS.
See merge request !582
idf_monitor: Small fixes (baud rate, EOL, /dev/tty.X on macOS, Ctrl-T on failure)
* "make monitor" now passed the configured baud rate.
Closes#436https://github.com/espressif/esp-idf/issues/436
* Pass toolchain prefix from sdkconfig into monitor tool
* Allow setting EOL in idf_monitor.py, use CRLF by default
* Detect if /dev/tty.X is used on macOS, warn and replace with /dev/cu.X
* If a build fails or gdb exits, ignore Ctrl-T (allowing Ctrl-T Ctrl-A/F to be same key sequence everywhere)
* Add a note about winpty on Windows.
Ref 02fdf8271d (commitcomment-21369196)
* Fix problems with Console.cancel() not existing in older pyserial
* Print more user-friendly symbols for "start of iram" and "start of flash"
See merge request !594
1. reset wifi mac when wifi start
2. roll back rx hung workaround for beacon timeout
3. fix amsdu ap interface wrong issue
4. fix amsdu header parse error
5. fix amsdu flag wrong issue
6. PHY: V350, fix BT rssi bug
7. RTC: V225, fix bt will be not work when wifi is reset
* Erase range operations allow preemption after each block or sector.
* Write operations allow preemption every 8KB of data.
* Reado operations allow preemption every 16KB of data.
This is to avoid confusion when idf_monitor prints the first symbol in each section, ie "WindowOverflow4" or similar,
when bootloader prints the section mapping address.
Closes#447https://github.com/espressif/esp-idf/issues/447
* "make monitor" not passed the configured baud rate
Closes#436https://github.com/espressif/esp-idf/issues/436
* Pass toolchain prefix from sdkconfig into monitor tool
* Allow setting EOL in idf_monitor.py, use CRLF by default
* Detect if /dev/tty.X is used on macOS, warn and replace with /dev/cu.X
* If a build fails or gdb exits, ignore Ctrl-T (allowing Ctrl-T Ctrl-A/F to be same key sequence everywhere)
* Add a note about winpty on Windows
Ref 02fdf8271d (commitcomment-21369196)
modify touch pad read function
The touch pad read function taks too much time within spin lock waiting for the "done bit". (about 7.6ms as we tested)
So we try to use a mutex on the touch read function and any other functions might change the "done bit".
See merge request !543
This issue is reported from https://github.com/espressif/esp-idf/issues/304.
We found that when we operate the hw command registers in I2C struct, sometimes the behaviour would be different in DEBUG/RELEASE optimisation level:
The code looks like this:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
In DEBUG configuration:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
400f3ab0: 3388 l32i.n a8, a3, 12
400f3ab2: 14c882 addi a8, a8, 20
400f3ab5: a08840 addx4 a8, a8, a4
400f3ab8: 0020c0 memw
400f3abb: 2898 l32i.n a9, a8, 8
400f3abd: 0020c0 memw
400f3ac0: 28b8 l32i.n a11, a8, 8
400f3ac2: 74a090 extui a10, a9, 0, 8
400f3ac5: 00af92 movi a9, 0xffffff00
400f3ac8: 109b90 and a9, a11, a9
400f3acb: 2099a0 or a9, a9, a10
400f3ace: 0020c0 memw
400f3ad1: 2899 s32i.n a9, a8, 8
In RELEASE configuration:
I2C[i2c_num]->command[p_i2c->cmd_idx].byte_num -= 0;
400f2ba2: 580572 l8ui a7, a5, 88
400f2ba5: 747070 extui a7, a7, 0, 8
400f2ba8: 0020c0 memw
400f2bab: 584572 s8i a7, a5, 88
Looks like the compiler will make it a 8bit operation after optimisation.
But the register value changes from 0x901 to 0x101.
After this 8-bit optimisation, the 11th bit changed from 1 to zero, which caused this error.
We are still trying to find out why that happens, because there might be some risk when operating the register struct.
This is a workaround to avoid "-=" operation on I2C register struct fields.
1. Add low speed channels for LEDC module.
2. Improve fade object allocate mechanism.
3. Improve ledc example, add 2 low speed channels in example.
4. Remove debug code
5. Improve the register bit field name of slow clock.
esp32: update wifi lib for some bugfix/features
1. add options to disable nvs
2. add station keepalive with softap
3. fix beacon rx start time not accurate issue
4. set wifi rx desc/buffer boundary check to internal memory boundary
See merge request !578
nvs_flash_init may return an error code in some cases, and applications
should check this error code (or at least assert on it being ESP_OK, to
make potential issues more immediately obvious).
This change modifies all the examples which use NVS to check the error
code. Most examples get a simple ESP_ERROR_CHECK assert, while NVS
examples, OTA example, and NVS unit tests get a more verbose check which
may be used in real applications.
Expand 'make monitor' support
New 'make monitor' idf_monitor tool for better monitor output. Running 'make monitor' will now:
* Automatically look up code addresses via addr2line and print function, source file, line number in terminal.
* Can reset the ESP32 by typing Ctrl-T Ctrl-R.
* Can run "make flash" by typing Ctrl-T Ctrl-F.
* Can run "make app-flash" by typing Ctrl-T Ctrl-A.
* If gdb stub starts, monitor will automatically run gdb and connect. When gdb exits, ESP32 resets and monitor resumes.
* Exit is still Ctrl-[
Have some more features I'd like to add (log output to file, crash dump support) but I think this is at the point of being useful.
See merge request !565
This change adds a check for the free page count to nvs_flash_init.
Under normal operation, NVS keeps at least one free page available,
except for transient states such as freeing up new page. Due to external
factors (such as NVS partition size reduction) this free page could be
lost, making NVS operation impossible. Previously this would cause an
error when performing any nvs_set operation or opening a new namespace.
With this change, an error is returned from nvs_flash_init to indicate
that NVS partition is in such a state.
make: don’t override TEST_COMPONENTS
When idf_monitor is launched from make, it gets modified `TEST_COMPONENTS`
variable which contains full paths to the test components instead of the
names. This causes `TEST_COMPONENT_PATHS` to be empty and the unit test
app gets built without any test components.
This change introduces an internal `TEST_COMPONENTS_LIST` variable which
gets set either from `COMPONENTS` if `TESTS_ALL` is 1, or from
`TEST_COMOPONENTS` otherwise.
Bootloader makefile is also fixed to avoid propagating `TESTS_ALL` to the
bootloader build step.
See merge request !569
bug fix: fix uart data bug when stop-bit is set as 2-bit mode
This is a workaround for a hardware bug.
When we want to use 2-stop-bit mode, we need to set stop-bit-1 and set dl1_en in rs485 register.
See merge request !544
1. add options to disable nvs
2. add station keepalive with softap
3. fix beacon rx start time not accurate issue
4. set wifi rx desc/buffer boundary check to internal memory boundary
The touch pad read function taks too much time within spin lock waiting for the "done bit". (about 7.6ms as we tested)
So we try to use a mutex on the touch read function and any other functions might change the "done bit".
When idf_monitor is launched from make, it gets modified TEST_COMPONENTS
variable which contains full paths to the test components instead of the
names. This causes TEST_COMPONENT_PATHS to be empty and the unit test
app gets built without any test components.
This change introduces an internal TEST_COMPONENTS_LIST variable which
gets set either from $(COMPONENTS) if TESTS_ALL is 1, and from
TEST_COMOPONENTS otherwise.
Bootloader makefile is also fixed to avoid propagating TESTS_ALL to the
bootloader build step.
bt component: fix bluetooth gatt packets process bugs
1. Add process of prepare write request packets
2. Add process of execute write request packets
3. Add process of reliable write request packets
4. Fix bug of processing read blob request packets
5. Fix bug of processing write request packets
6. Optimize error check and process in stack
See merge request !558
add wakeup from touch sensor, and deep sleep example
- add new deep sleep wakeup mode
- change documentation to explain incompatibilities between different wakeup mode, add error checks
- add new ULP instructions necessary for ULP wakeup scenario
- fix issues with I_WR_REG, I_SLEEP, I_END instructions
- add deep sleep example, illustrating the use of timer, gpio, touch, and ULP wakeup triggers
See merge request !461
add extra check before bluedroid init and disable
add extra check before bluedroid init and disable to avoid the mixed call cause unexpected errors.
See merge request !553
component/bt: optimize stack size of Bluetooth Tasks and make them be configurab…
Bluetooth tasks' stack size are optimized and can be configured by the CONFIG_NEWLIB_NANO_FORMAT option.
See merge request !559
esptool version bump and new "espefuse.py set_flash voltage" command
* New "espefuse.py set_flash_voltage" command to easily set a fix
VDD_SDIO regulator voltage (1.8V, 3.3V or disabled).
* Fixes bugs when flashing files with non-4-byte aligned lengths
(doesn't effect esp-idf image files)
* esptool README improvements
* Detect overlapping files in write_flash
* read_mac now works correctly on ESP32
* Integrates reset fix for older dev boards (formerly the "Windows ESP32R0 reset workaround")
See merge request !481
Change max number of open sockets
Change max number of open sockets from 16 to 32 because of MFI project need support 21 open sockets at least.
See merge request !532
1. Add process of prepare write request packets
2. Add process of execute write request packets
3. Add process of reliable write request packets
4. Fix bug of processing read blob request packets
5. Fix bug of processing write request packets
6. Optimize error check and process in stack
Fix partition- and mmap-related issues
- Fix unit tests failing to start up due to a mismatch between sdkconfig flash size and size required by partition table.
- Fix a bug that partition APIs loaded the partition table in reverse order. As such, `esp_partition_next` and `esp_partition_find_first` did not work as expected. Add a test.
- Update the workaround for stale cache reads issue: do Cache_Flush for non-encrypted flash as well. Add a test.
See merge request !555
The issue that cache entries are not invalidated correctly sometimes
can also be reproduced for non-encrypted flash as well.
This change updates the workaround to do Cache_Flush, enabling it for
non-encrypted flash, and adds a unit test.
- change order of assert arguments to (expected, actual)
- set expected partition count to 3 to match the new partition table
- use the new get_test_partition facility
- check that partitions are listed in correct order
- remove leftover debugging printfs
Originally marked "Reset with ESP32R0 Windows workaround", but proven to be
necessary on some other platforms as well. This is now integrated into the
default esptool.py reset behaviour.
Closes#305https://github.com/espressif/esp-idf/issues/305
* New "espefuse.py set_flash_voltage" command to easily set a fix
VDD_SDIO regulator voltage (1.8V, 3.3V or disabled).
* Fixes bugs when flashing files with non-4-byte aligned lengths
(doesn't effect esp-idf image files)
* README improvements
Allow separate ethernet & wifi configuration
If only 1/2 of ethernet & WiFi are enabled in config, the other interface is no longer linked into the firmware.
* Fixes bug where enabling Ethernet but not WiFi would fail to compile.
* Also means that enabling WiFi but not Ethernet no longer links some unused ethernet interface functions.
See merge request !525
FreeRTOS: Fix cross-core event group sync
As above
Also includes fixes which allowed removing some semi-hacky bits from the event group unit tests - specifically, higher priority tasks will always be started immediately even if they run on the opposite core.
See merge request !535
FATFS enable support for multiple drives
Current implementation has drive numbers and paths hardcoded to support
only one FATFS drive. Arduino has it's own SPI driver to allow
compatibility and flexibility. With the MR it is possible to have up to
```_VOLUMES``` drives connected (SPI, SDMMC and others) at the same
time and accessed through VFS
See merge request !478
freertos kconfig: Add max task length name, move task stack overflow watchpoint
* Allow setting task name length via kconfig
* Move task stack overflow watchpoint out of internals debugging submenu, place next to other stack overflow checks.
* Thread local pointer feature should depend on Ethernet or WiFi
See merge request !531
Partition/SPI/OTA docs & OTA new functionality
* Update partition, SPI flash & OTA docs to reflect functionality changes
* Refactor OTA implementation to perform checks mentioned in API doc
* Add new functions to OTA API: esp_ota_get_running_partition() & esp_ota_get_next_update_partition() functions
* Add spi_flash_cache2phys() & spi_flash_phys2cache() functions to support esp_ota_get_running_partition()
See merge request !513
Feature/add user set mac
1. Add menuconfig for user to set mac address of wifi, bt and ethernet.
2. Add the number of MAC address generated from efuse for user to choose.
3. Add MAC address derive method.
See merge request !542
esp32: Fix hardware rng after esp_wifi_stop (second implementation)
Ensures hardware RNG remains enabled at all times.
Reworked version of !534
See merge request !536
lwip: modify dhcp timer granularity from 60s to 1s
Current DHCP granularity is 60 seconds, it's not accurate, it can cause DHCP release/rebind/renew timer
timeout at the same time, also it may renew/rebind/release at wrong time, thus cause problem.
1. RTC V214: modify APLL function for the chip of ECO version.
2. Add API phy_close_rf() and use it in esp_phy_deinit() instead of pm_close_rf().
3. RTC V213: fix BT will not work when BT-init is called more than once.
vfs_fat_sdmmc: if card init fails, fail cleanly
This fixes the issue with sdmmc_host not returned to clean state after a failed attempt to mount the card, with no SD card in the slot.
See merge request !527
component/bt : add adv/scan start complete event
1. indicate adv/scan start complete success or failed
2. controller do limit of adv/scan concurrence, so add some codes to report adv/scan start failed or not.
See merge request !524
component/bt:fixed the write ccc crash bug error
fix the gatt server write ccc lead to the system crash if not initialize the ccc value.
See merge request !515
Optimize or release memory in bluetooth
1. add option to release about 30K from BT if BLE only
2. later BT/BLE will be separated by BT/BLE macro, but this option should use when user make sure that in BLE only mode.
See merge request !520
1. indicate adv/scan start complete success or failed
2. controller do limit of adv/scan concurrence, so add some codes to report adv/scan start failed or not.
The root cause is the bug in bluetooth controller, in which the HCI_SNIFF_MODE command is sent to controller and at the same time the controller has received same request from remote device.
For now change the time-out period of local device to enter the SNIFF mode.
Fix a scheduling bug
Fixes:
- Trivial bug where in some special cases a task could be started on the wrong core (and would run there for max 1 tick)
- More major bug causing a yield to be done with a mux held.
See merge request !523
Fix SPI master transmit length
Tx/Rx length fix from https://github.com/espressif/esp-idf/pull/336
I also added an extra commit in to make use of a define instead of a literal, plus fix a (harmless) off-by-one condition.
See merge request !521
This fixes incorrect descriptions of I_END/I_SLEEP instructions and
changes the definition of I_END. New instruction, I_WAKE, is added,
which wakes up the SoC. Macro for ADC instruction is defined, and new
tests are added.
This change adds esp_deep_sleep_get_wakeup_cause, which returns the
source which has caused wakeup from deep sleep.
Similar to esp_deep_sleep_get_ext1_wakeup_status, a function is added
to check touch pad wakeup status: esp_deep_sleep_get_touchpad_wakeup_status.
This function returns the touch pad which has caused wakeup.
ULP and touch FSMs in ESP32 revisions 0 and 1 do not operate correctly
if RTC_PERIPH power domain is force powered on (ESP_PD_OPTION_ON).
Both ULP and touch still work, but clock frequency of the ULP may be
incorrect and touch values may be off by considerable amount. As such,
when these wakeup modes are used, RTC_PERIPH power domain has to be set
to ESP_PD_OPTION_AUTO (or, in the current implementation,
ESP_PD_OPTION_OFF — though this will change in the future when _OFF will
actually *force* the power domain to be powered off).
Because EXT0 wakeup source requires RTC_PERIPH to be powered ON, mark
ULP and touch wakeup sources as incompatible with EXT0. Workaround for
this is to use EXT1 wakeup source instead, which offers similar or
better functions without having to keep RTC_PERIPH powered on.
- I_RD_REG used the wrong union member (.rd_reg) due to a copy-paste
mistake
- Peripheral register address in bits[7:0] should be given in words,
not in bytes
Fixes https://github.com/espressif/esp-idf/issues/297
Deep sleep fixes
This change fixes extra 24 uA current consumption in deep sleep mode (https://esp32.com/viewtopic.php?f=2&t=1133).
Recent update to libphy/librtc caused another problem that WiFi related parts of RTC are no longer disabled by RTC sleep functions. This means that if WiFi is not disabled by the application before entering deep sleep, extra ~200uA of current would be consumed. This is fixed, and documentation for esp_deep_sleep and SNTP example are updated to mention that applications should take care of disabling WiFi and BT before going into the deep sleep mode.
See merge request !516
spi_flash: fix protection issues
This MR fixes the two spi_flash related issues:
- esp_intr_noniram_{disable,enable} not being protected by spi_flash_op_{lock,unlock} in single core mode. This caused a safety assert to be triggered in esp_intr_noniram_disable.
- spi_flash_unlock not being protected by spi_flash_guard_{start,end}. This caused a conflict between SPI0 and SPI1 controllers when accessing SPI flash, manifesting in cache data corruption and IllegalInstruction exceptions, for some flash chips.
See merge request !522
spi_flash_unlock was missing spi_flash_guard_start, which caused cache
to be enabled during unlock operation, causing hard-to-trace crashes
and cache data corruption.
MR !441 (7c155ab) has fixed issue with esp_intr_noniram_{disable,enable}
calls not being properly protected by spi_flash_op_{lock,unlock}.
Unit test was added, but the unit test environment tests only dual-core
config. Similar issue was present in the code path for the single-core
config, where esp_intr_noniram_{disable,enable} calls were unprotected.
This change fixes the protection issue and updates the unit test to
run properly in single core config as well.
The issue with running unit tests for single core config will be
addressed in a separate MR.
In case WiFi/BT stack has been enabled but wasn’t disabled, some RTC
bits may be left enabled, causing increased current consumption.
This change returns some of the bits back to their default values.
Bootloader enables SAR ADC in test mode to get some entropy for the RNG.
The bits which control the ADC test mux were not disabled, which caused
extra ~24uA current to be drawn from VRTC, increasing deep sleep current
consumption. This change disables relevant test mode bits in
bootloader_random_disable.
1. add new APIs bt controller enable/disab/deinit
2. make bt controller work need to call two APIs of esp_bt_controller_init and enable
3. modify phy init to make mac reset once
1. add a macro in menuconfig for users to choose whether store phy calibration data into NVS or not.
2. rename some disable phy and rf APIs so that existing code which calls old APIS will fail to compile.
1. Add disable PHY and RF when WiFi and BT are both disabled(including call sniffer disable API).
2. Do not init PHY and RF when cpu start. Init PHY and RF when call Wifi or BT start APIs(including sniffer enable API).
3. Add a temporary lib: librtc_clk.a and will delete it when CPU frequency switching function is done.
4. Add an function to get OS tick rate.
5. Do not put the whole pp.a in iram0, only put lmac.o, ieee80211_misc.o, ets_time.o and wdev.o in iram0.
This connection error caused by iPhone, it think that TX data length must large than 27 when slave support EXTEND_DATA_LENGTH. But this should be allow. Besides, the problem cannot be found on higher version of Iphone7, apple seemed to have fixed it.
Actually maybe other BLE device have the same problem.
Docs: Document flash encryption disable steps, clean up flash encryption & secure boot docs
Generate clean up of flash encryption & secure boot docs
Including steps for disabling flash encryption (for people who accidentally enable it).
See merge request !500
phy_init: don’t rewrite valid calibration data
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
See merge request !487
freertos: fix protection issue in freertos queue event list
When functions in queue.c calls listLIST_IS_EMPTY() to check queue event list, the queue list is
protected by queue mutex, on the other hand, when xTaskIncrementTick() modify the queue list, the
queue list is protected by xTaskQueueMutex, this may cause xTaskRemoveFromEventList operate on
the empty queue list and cause problem.
This change works around the problem by reducing the window where the race condition can happen.
See merge request !465
Also add steps to disable flash encryption, as some people seem to
accidentally enable it.
Explicitly mark the flash encryption and secure boot as "READ DOCS
FIRST" in menuconfig.
esp32: update wifi lib for some fixes and optimizations
1. Reduce the default static rx buffer size from 25 to 10
2. Adjust ampdu interrupt size to 3, namely, raise 1 interrupt per 3-mpdu
3. Make a copy for all received packets, including AMSDU/AMPDU/MPDU
4. Fix softap mis-forward issue
5. Fix pp q full issue
6. Fix sniffer copy wrong content issue
See merge request !491
When functions in queue.c calls listLIST_IS_EMPTY() to check queue event list, the queue list is
protected by queue mutex, on the other hand, when xTaskIncrementTick() modify the queue list, the
queue list is protected by xTaskQueueMutex, this may cause xTaskRemoveFromEventList operate on
the empty queue list and cause problem. This commit is to fix this bug.
may cause
1. Reduce the default static rx buffer size from 25 to 10
2. Adjust ampdu interrupt size to 3, namely, raise 1 interrupt per 3-mpdu
3. Make a copy for all received packets, including AMSDU/AMPDU/MPDU
4. Fix softap mis-forward issue
5. Fix pp q full issue
6. Fix sniffer copy wrong content issue
Fix interrupting task on other CPU that has lower prio than current task on current CPU
Fix for a very subtle bug introduced somewhere in december. This bug would cause a cross-core interrupt to only be sent if the activated task has a higher priority than the task currently running on *this* cpu, instead of on the other CPU.
See merge request !475
In the default PHY init routine, calibration data is loaded from NVS.
Most of the time the incremental changes to calibration will be fairly
small, so we don’t need to rewrite the existing calibration data stored
in the NVS.
Possible enhancement to be done in the future: expose a function in PHY
library to tell how big was the change in calibration data. If the
change was significant, then calibration data stored in NVS should be
updated.
esp32: Fixes watchdog problem when printing core dump to uart
1) Fixes watchdog problem when printing core dump to uart
2) Also fixes generation of core dumps when flash cache is disabled
See merge request !472
Current implementation has drive numbers and paths hardcoded to support
only one FATFS drive. Arduino has it's own SPI driver to allow
compatibility and flexibility. With the MR it is possible to have up to
```_VOLUMES``` drives connected (SPI, SDMMC and others) at the same
time and accessed through VFS
components/openssl: refactor openssl debugging and assert function
1. add openssl option at menuconfig
2. remove SSL_ERR to reduce complexity
3. add more functions about debugging and assert
According these, our coders and customers may use and debug the OpenSSL code easily.
See merge request !400
Use PART_FLAG_ENCRYPTED value in gen_esp32part.py
Currently paritions marked as encrypted by gen_esp32part.py are not
recognized as such and encrypted writes don't work.
This is part of espressif/esp-idf#253
Merges Pull Request #293https://github.com/espressif/esp-idf/pull/293
See merge request !470
Add missing variable initialisation to make SPI work for multiple CS
Ref https://github.com/espressif/esp-idf/pull/277
From PR: "I am not especially familiar with this platform or with esp-idf -- so review with care.
The spi-master driver would not work for me when the number of devices on a bus exceeded 1 (caused device hang). I believe this is because cur_cs is not properly set (anywhere), and yet is used. This is likely just not noticed because 0 is presumably the correct value when there's only 1 device (and I'm guessing multi-device setup is not tested as thoroughly).
Simply setting cur_cs to the correct slot value resolves the problem and multiple devices on a single bus behave correctly in my test environment."
Looks like a small oversight on my side.
See merge request !468
1. fix ampdu<->mpdu<->ampdu switch may cause rx slow issue by put mpdu into ampdu reorder queue
2. fix each ac first sending always fail issue by adding retry
Seems doing certain kinds of short reads while flash encryption is
enabled will return stale data. This fixes it, but is probably a
little heavy-handed performance wise.
Verify 0xE9 magic byte on first write, verify entire image before
switching.
Enable verification for secure boot signature (was using invalid ifdef
guard)
Currently paritions marked as encrypted by gen_esp32part.py are not
recognized as such and encrypted writes don't work.
This is part of espressif/esp-idf#253
lwip: optimize the dhcp client
1. modify the discover retry backoff time from (2,4,8,16,32,60,60)s to (500m,1,2,4,8,15,15)s.
2. add DHCP_DOES_ARP_CHECK to menuconfig for users to specify if do a ARP check on the offered address.
If enable, one more second will be taken.
See merge request !459
1. modify the discover retry backoff time from (2,4,8,16,32,60,60)s to (500m,1,2,4,8,15,15)s.
2. add DHCP_DOES_ARP_CHECK to menuconfig for users to specify if do a ARP check on the offered address.
If enable, one more second will be taken in obtaining IP address.
3. update wifi libs
Without this, it's possible for stale information to be read from
cache via mmap, even if the MMU table entry had been invalidated
prior to writing flash (if the same MMU table entry was re-used after
writing flash.)
docs: use custom roles to generate GitHub links
This change replaces direct links to GitHub master branch with
auto-generated links using docutils custom roles.
These auto-generated links point to the tree or blob for the git commit
ID (or tag) of the repository. This is needed to ensure that links don’t
become broken when files in master branch are moved around or deleted.
The following roles are introduced:
```
- :idf:`path` - points to directory inside ESP-IDF
- :idf_blob:`path` - points to file inside ESP-IDF
- :idf_raw:`path` - points to raw view of the file inside ESP-IDF
- :component:`path` - points to directory inside ESP-IDF components dir
- :component_blob:`path` - points to file inside ESP-IDF components dir
- :component_raw:`path` - points to raw view of the file inside ESP-IDF
components dir
- :example:`path` - points to directory inside ESP-IDF examples dir
- :example_blob:`path` - points to file inside ESP-IDF examples dir
- :example_raw:`path` - points to raw view of the file inside ESP-IDF
examples dir
```
A check is added to the CI build script, which searches RST files for
presence of hard-coded links (identified by tree/master, blob/master,
or raw/master part of the URL).
This check can be run manually: cd docs && make gh-linkcheck
Additionally, Sphinx linkcheck build type is used to create new CI test,
which check for broken links. This test has to be triggered explicitly,
because including it in normal build process (when the commit is not yet
deployed to Github) will not work. It can be triggered in a regular
fashion using a combination of cron and Curl, similar to stress tests.
See merge request !455
This change replaces direct links to GitHub master branch with
auto-generated links using docutils custom roles.
These auto-generated links point to the tree or blob for the git commit
ID (or tag) of the repository. This is needed to ensure that links don’t
become broken when files in master branch are moved around or deleted.
The following roles are introduced:
- :idf:`path` - points to directory inside ESP-IDF
- :idf_blob:`path` - points to file inside ESP-IDF
- :idf_raw:`path` - points to raw view of the file inside ESP-IDF
- :component:`path` - points to directory inside ESP-IDF components dir
- :component_blob:`path` - points to file inside ESP-IDF components dir
- :component_raw:`path` - points to raw view of the file inside ESP-IDF
components dir
- :example:`path` - points to directory inside ESP-IDF examples dir
- :example_blob:`path` - points to file inside ESP-IDF examples dir
- :example_raw:`path` - points to raw view of the file inside ESP-IDF
examples dir
A check is added to the CI build script, which searches RST files for
presence of hard-coded links (identified by tree/master, blob/master,
or raw/master part of the URL).
This check can be run manually: cd docs && make gh-linkcheck
Additionally, Sphinx linkcheck build type is used to create new CI test,
which check for broken links. This test has to be triggered explicitly,
because including it in normal build process (when the commit is not yet
deployed to Github) will not work. It can be triggered in a regular
fashion using a combination of cron and Curl, similar to stress tests.
1. clean up bluetooth storage log prints;
2. reduce maximum link key storage size
3. modify so that the link key information of the latest connected device is stored at first
Update esptool.py to v2.0-beta1
* Minor bug fixes, no major functionality changes from the esp-idf perspective.
* Now tracks master branch of esptool repo (finally!)
* Supports Python 3, although our other esp-idf Python tools don't yet support Python 3.
See merge request !396
If the DNS request is dispatched and performed very quickly,
then it can complete before tcpip_callback() actually returns,
in which case we'll destroy the actual err_t error value passed
in the message. Use a local variable for the tcpip_callback
error code so that can't happen.
Resolves#269https://github.com/espressif/esp-idf/pull/269
Move PHY options out of WiFi config, improve descriptions
- move PHY-related settings into new menu, make it dependent on WIFI_ENABLED || BT_ENABLED
- improve descriptions of Ethernet Kconfig options
See merge request !443
ESP32_PHY_MAX_TX_POWER option is only meaningful for WiFi, so previous
change made it depend on WIFI_ENABLED. However if WiFi is not enabled,
but BT is, this option becomes undefined which breaks phy_init_data
generation.
This change turns ESP32_PHY_MAX_TX_POWER into a hidden parameter, which
depends on PHY_ENABLED. New user-visible parameter,
ESP32_PHY_MAX_WIFI_TX_POWER is introduced which depends on WIFI_ENABLED
and is used as default value for ESP32_PHY_MAX_TX_POWER if WIFI_ENABLED
is set. Otherwise ESP32_PHY_MAX_WIFI_TX_POWER is set to 20.
newlib: fix register used for DPORT/RTC bug workaround
While there was no register at DR_REG_FRC_TIMER_BASE + 0x60, due to
peripheral address space wraparound this write actually affected one of
FRC2 registers, which is used by WiFi stack to implement legacy
ets_timer APIs.
This change uses FRC_TIMER_LOAD_REG(0) instead, which can be set to
known value safely.
See merge request !449
fixes for issues observed when using spi_flash
This MR fixes three unrelated issues:
- Race condition in spi_flash_enable_interrupts_caches_and_other_cpu
when operations on unpinned tasks are performed.
The issue is reported in https://github.com/espressif/esp-idf/pull/258
- esp_intr_noniram_disable doesn’t disable interrupts when compiled in
release mode. This issue manifested itself with an illegal instruction
exception when task WDT ISR was called at the time when flash was
disabled.
Fixes https://github.com/espressif/esp-idf/issues/263.
- Tick hooks on CPU1 were not called if CPU0 scheduler was disabled for
significant amount of time (which could happen when doing flash erase).
The issue manifested itself as “INT WDT timeout on core 1” error.
Fixes https://github.com/espressif/esp-idf/issues/219.
See merge request !441
While there was no register at DR_REG_FRC_TIMER_BASE + 0x60, due to
peripheral address space wraparound this write actually affected one of
FRC2 registers, which is used by WiFi stack to implement legacy
ets_timer APIs.
This change uses FRC_TIMER_LOAD_REG(0) instead, which can be set to
known value safely.
The block which dispatches ticks on CPU1 was a copy of the code block
for the normal path (CPU0). It used to check uxPendedTicks, with the
logic that uxPendedTicks can be 0 iff the scheduler is not suspended.
On CPU1 however, uxPendedTicks is not related to the state of the
scheduler (as uxPendedTicks is updated on CPU0). Due to this, if CPU0
scheduler was suspended, and uxPendedTicks happened to be nonzero,
tick hooks on CPU1 didn’t run, even though CPU1 scheduler was working.
This change removes the check for uxPendedTicks in CPU1 code path,
so that the tick hooks on CPU1 always get called (as for the CPU0 code
path).
Allow writes to encrypted partitions
There is a size alignment requirement but it is checked by
spi_flash_write_encrypted. However, this check flat-out bans encrypted
writes.
Original PR on Github: https://github.com/espressif/esp-idf/pull/249
See merge request !432
When compiling in release mode, compiler was choosing same register for
oldint and intmask variables, so INTENABLE was never modified.
This effectively broke disabling of non-IRAM interrupts during flash
operations, observed in the existing tests if task watchdog is enabled.
This change adds an extra constraint tells the compiler that output
operand should not be placed into the same register as an input one.
Add python script that parses list of unit test cases for CI from component test folder
Modify .gitlab-ci.yml to run this script as part of build unit tests stage
spi_flash_enable_interrupts_caches_and_other_cpu function used to enable
non-IRAM interrupts after giving up flash operation lock, which would
cause problems if another task was waiting on the lock to start a flash
operation. In fact, non-IRAM interrupts should be re-enabled before the
task scheduler is resumed. Otherwise non-pinned task can be moved to the
other CPU due to preemption, causing esp_intr_noniram_enable to be
called on the other CPU, causing an abort to be triggered.
Fixes the issue reported in
https://github.com/espressif/esp-idf/pull/258
Delete option to select core timer 2 as a FreeRTOS tick source
Core timer 2 is unusable for FreeRTOS ticks because it triggers a high-level interrupt. This MR deletes the option to select it.
Ref https://github.com/espressif/esp-idf/issues/234
See merge request !418
