Restores the change of startup refactor changes removed the no stack
check protection flag when compiling the source file that contains
execution of constructors - which contains function to setup stack
guard. Restore that and update the source file, since this is in the 2nd
stage of the startup now.
Closes https://github.com/espressif/esp-idf/issues/5617
Allows booting in QIO/QOUT mode or with PSRAM on ESP32-PICO-V3 and
ESP32-PICO-V3-O2 without any config changes.
Custom WP pins (needed for fully custom circuit boards) should still be compatible.
This commit adds TWAI driver support for the
ESP32-S2. The following features were added:
- Expanded BRP support
- Expanded CLKOUT Divider Support
- Updated example READMEs
The issue is caused by:
1. The disable_qio_mode inside read_id may have side effects.
2. read_id twice may have side effects.
Fix this issue by moving disable_qio_mode out of read_id and only do it
once before read_id. And retry read_id only when the first one is
failed.
Issue introduced in 3ecbb59c15.
esp32/esp32s2: Reduce using ESP_EARLY_LOGx and move some code after the stdout initialization in startup code
Closes IDFGH-3367
See merge request espressif/esp-idf!8904
On ESP32, due to fifo reset issue, UART2 will work incorrectly if reset the fifo of UART1(TX fifo and RX fifo). The software can workaround the RX fifo reset issue,
while the TX fifo reset issue can not. When UART2 is used and UART1 is used as the log output port, a software reset can reproduce this issue. So we should reset the UART memory
before the software reset to solve this problem.
If esp_restart_noos() is run and the stack address points to external memory (SPIRAM)
then Cache_Read_Disable() raises up the error "Cache disabled but cached memory region accessed"
to fix this we switch stack to internal RAM before disable cache.
Added unit tests.
Closes: https://github.com/espressif/esp-idf/issues/5107
- for ESP32 only enabled in case of unicore config
- capability wise this region (8K) is same as DRAM, except non-DMA capable
- also fixed small issue in reserved memory region processing when (start == end)
This commit updates the watchdog timers (MWDT and RWDT)
in the following ways:
- Add seprate LL for MWDT and RWDT.
- Add a combined WDT HAL for all Watchdog Timers
- Update int_wdt.c and task_wdt.c to use WDT HAL
- Remove most dependencies on LL or direct register access
in other components. They will now use the WDT HAL
- Update use of watchdogs (including RTC WDT) in bootloader and
startup code to use the HAL layer.
1. add enable PSRAM 2T mode function
2. enable PSRAM 2T mode base on PSRAM ID
3. abort when himem and 2T mode are enabled meanwhile
4. set SPIRAM_2T_MODE as "y" by default and modify SPIRAM_BANKSWITCH_ENABLE as "n" by default
Configurable option to use IRAM as byte accessible memory (in single core mode) using
load-store (non-word aligned and non-word size IRAM access specific) exception handlers.
This allows to use IRAM for use-cases where certain performance penalty
(upto 170 cpu cycles per load or store operation) is acceptable. Additional configuration
option has been provided to redirect mbedTLS specific in-out content length buffers to
IRAM (in single core mode), allows to save 20KB per TLS connection.
1. add brownout detector HAL for esp32 and esp32s2
2. enable brownout reset for esp32 rev. 1 and above
3. add approximate brownout detector levels for esp32s2
1. Clarify THREADPTR calculation in FreeRTOS code, explaining where
the constant 0x10 offset comes from.
2. On the ESP32-S2, .flash.rodata section had different default
alignment (8 bytes instead of 16), which resulted in different offset
of the TLS sections. Unfortunately I haven’t found a way to query
section alignment from C code, or to use a constant value to define
section alignment in the linker script. The linker scripts are
modified to force a fixed 16 byte alignment for .flash.rodata on the
ESP32 and ESP32-S2beta. Note that the base address of .flash.rodata
was already 16 byte aligned, so this has not changed the actual
memory layout of the application.
Full explanation of the calculation below.
Assume we have the TLS template section base address
(tls_section_vma), the address of a TLS variable in the template
(address), and the final relocation value (offset). The linker
calculates:
offset = address - tls_section_vma + align_up(TCB_SIZE, alignment).
At run time, the TLS section gets copied from _thread_local_start
(in .rodata) to task_thread_local_start. Let’s assume that an address
of a variable in the runtime TLS section is runtime_address.
Access to this address will happen by calculating THREADPTR + offset.
So, by a series of substitutions:
THREADPTR + offset = runtime_address THREADPTR = runtime_address - offset
THREADPTR = runtime_address - (address - tls_section_vma + align_up(TCB_SIZE, alignment)) THREADPTR = (runtime_address - address) + tls_section_vma - align_up(TCB_SIZE, alignment)
The difference between runtime_address and address is same as the
difference between task_thread_local_start and _thread_local_start.
And tls_section_vma is the address of .rodata section, i.e.
_rodata_start. So we arrive to
THREADPTR = task_thread_local_start - _thread_local_start + _rodata_start - align_up(TCB_SIZE, alignment).
The idea with TCB_SIZE being added to the THREADPTR when computing
the relocation was to let the OS save TCB pointer in the TREADPTR
register. The location of the run-time TLS section was assumed to be
immediately after the TCB, aligned to whatever the section alignment
was. However in our case the problem is that the run-time TLS section
is stored not next to the TCB, but at the top of the stack. Plus,
even if it was stored next to the TCB, the size of a FreeRTOS TCB is
not equal to 8 bytes (TCB_SIZE hardcoded in the linker). So we have
to calculate THREADPTR in a slightly obscure way, to compensate for
these differences.
Closes IDF-1239
Even if frame->exccause != PANIC_RSN_CACHEERR, it is possible that
the cache error interrupt status is set. For example, this may happen
due to an invalid cache access in the panic handler itself.
Check cache error interrupt status instead of frame->exccause to
decide whether to do CPU reset or digital reset.
Also remove unnecessary esp_dport_access_int_pause from
esp_cache_err_get_cpuid, since the panic handler already calls
esp_dport_access_int_abort on entry.
arg1 = MAX(int64_t arg1, uint64_t arg2) gave the wrong result, if arg1 < 0, it was presented as a larger value.
And ALARM_REG = (uin32_t)arg1. This leads to an infinite loop.
Fixed: both args are int64_t.
Closes: WIFI-1511
Activated AES, RSA and SHA hardware acceleration for esp32s2 and enabled related unit tests.
Updated with changes made for ESP32 from 0a04034, 961f59f and caea288.
Added performance targets for esp32s2beta
Closes IDF-757
1. Fix WiFi scan leads to poor performance of Bluetooth.
2. Improve WiFi connect success ratio when coexist with Bluetooth.
3. Check if WiFi is still connected when CSA or beacon timeout happen.
4. add coex pre init
The test case may run after an RTC_WDT_RESET (if we are on rev. 0
ESP32), or software reset (when running test cases locally).
Also moving the test case next to the other timer group driver tests.
1. add hal and low-level layer for timer group
2. add callback functions to handle interrupt
3. add timer deinit function
4. add timer spinlock take function
The workaround for PSRAM that will occupy an SPI bus is enabled only when:
1. used on 32MBit ver 0 PSRAM.
2. work at 80MHz.
The test used to only check 32MBit by the config option, but for PSRAM
on Wrover-B module seems to use a newer version of 32MBit PSRAM. So it
expects the workaround to be enabled, but actually not.
This commit split the unit test into two parts:
1. check all SPI buses are available, for all configs except psram_hspi
and psram_vspi, run on regular runners (including Wrover and Wrover-B).
a hidden option is enabled so that the compiler knows it's not building
psram_hspi or psram_vspi.
2. check the specified bus are acquired, for config psram_hspi and
psram_vspi. This only run on special runner (legacy Wrover module).
esp32s2beta: Merge support to master
Closes IDF-513, IDF-756, IDF-758, IDF-999, IDF-753, IDF-749, IDF-754, IDF-840, and IDF-755
See merge request espressif/esp-idf!6100
1. Since BLE full-scan feature for BLE mesh change the controller code cause this problem,
it cause coex semaphore take in "interrupt disable", then it may cause task schedule
and cause crash in freertos
2. Fix newlib lock ISR context and critical section check
3. Fix bt controller ISR context and critical section check
Ref. https://github.com/espressif/esp-idf/issues/1684
This change allows RTTI to be enabled in menuconfig. For full RTTI
support, libstdc++.a in the toolchain should be built without
-fno-rtti, as it is done now.
Generally if libstdc++.a is built with RTTI, applications which do not
use RTTI (and build with -fno-rtti) could still include typeinfo
structures referenced from STL classes’ vtables. This change works
around this, by moving all typeinfo structures from libstdc++.a into
a non-loadable section, placed into a non-existent memory region
starting at address 0. This can be done because when the application
is compiled with -fno-rtti, typeinfo structures are not used at run
time. This way, typeinfo structures do not contribute to the
application binary size.
If the application is build with RTTI support, typeinfo structures are
linked into the application .rodata section as usual.
Note that this commit does not actually enable RTTI support.
The respective Kconfig option is hidden, and will be made visible when
the toolchain is updated.
