Hardware AES-CBC performance changes:
Release config 11.0MB/sec -> 10.8MB/sec
Debug config 9.4MB/sec -> 9.8MB/sec
(Unrolling the loop to optimize the check improves
performance at -Og, even with the fault check.)
1. resend eb which are pending in g_ic.tx_buf due to channel switch.
2. add lock for mgmg/xon/bcast to protect send from user flush.
3. softap: add check if secondary offset is correct when start softap.
4. softap: in inactive timer handler, add check if child bss is removed to avoid removing it again.
5. disable A-MPDU for non-root.
6. fix reusing a freed eb.
7. fix when node becomes root, it does not record assoc value to nvs.
8. discard unnecessary forwarded group packets.
9. fix toDS state is not updated in time.
10. fix s_sta_cnx_times is not cleared when deinit causes root sends ADD annoucement.
11. root: increase beacon timeout time from 6 seconds to 15 seconds to delay initiation of reconnection.
12. add esp_mesh_get_tsf_time to return TSF time.
13. send the whole routing table multi-times.
14. clear candidate settings if not receive candidate beacon within 8 seconds.
When flash work in DIO Mode, in order to ensure the fast read mode of flash
is a fixed value, we merged the mode bits into address part, and the fast
read mode value is 0 (the default value).
Fixed the case when the first part of log was missed
this was happened when:
* CONFIG_CONSOLE_UART_CUSTOM option is selected (UART1)
* The selected CONSOLE_UART port is used also for the console component
* in code esp_restart() or abort() functions were called.
Fix following wpa2 enterprise vulnerability issues:
1. The station can complete 4-way handshake after EAP-FAIL is received
2. The station crashes if EAP-SUCCESS is received before PMK is setup
1. Softap support multicast and broadcast saving and flushing when the associated stations enable IEEE80211 legacy power save(which is called modem sleep in ESP32).
2. Improve the frame saving and flushing mechanism of softap power save.
1. remove redundant SPI clock settings, use rom functions to set clock.
2. remove redundant SPI cs setup and hold settings.
3. for old 32Mbit psram, cs hold time must only be 0.5T due to the special driving mode.(cs_setup = 0; cs_hold = 0)
4. for new 64Mbit psram, cs hold time is recommended to be 2.5T. (cs_setup = 1, cs_setup_time = 0;cs_hold = 1, cs_hold_time = 1)
Linker script generator produces build/esp32/esp32.common.ld from
components/esp32/ld/esp32.common.ld.in
This works fine until IDF is downgraded to V3.1 which uses components/esp32/ld/esp32.common.ld and
doesn't track build/esp32/esp32.common.ld at all.
At this point, the linker runs in the build/esp32 directory and "-T esp32.common.ld" picks up the
linker script generated .ld file, which causes mis-builds.
As reported on forums: https://esp32.com/viewtopic.php?f=13&t=9684&p=40105
Fix following STA WFA certification issues:
1. STA HT2040 coexist
2. Disallow WEP/TKIP with HT rates
3. WPA2 improvement
4. Minor refactor for WiFi internal global variable auth_type
remove duplicated include from components/esp32/incliude/esp_core_dump.h
espcoredump/incliude/esp_core_dump.h:
fix signature of the functions esp_core_dump_to_uart() and esp_core_dump_to_uart();
add espcoredump into COMPONENT_PRIV_REQUIRES list
fix linker.lf file
1. Add Kconfig options to control task listing support.
2. Convert magic values (-1, -2) to named constants.
3. Convert spaces to tabs to match the rest of the file.
4. Rename getAllTasksHandle to getTaskInfo to reflect its purpose.
5. Add some curly braces for single line statements.
Fix following WiFi bugs:
1. Fix the bug that STA incorrectly deletes BA when receiving DelBA request
2. Add out of memory check
3. Fix the bug that STA incorrectly receives packets when scanning in connected status
Previously, this compiler flag was not being applied
regardless of CONFIG_SPIRAM_CACHE_WORKAROUND setting.
Explanation: add_compile_options() only applies to
source files added after the function is run, or in
subdirectories added after the function is run. In
this case, no new source files were being added after
this function was run.
1. ref_clock used in unit tests occasionally produces time off by ~100
microseconds shortly after being started. Add a delay to let
ref_clock stabilise, until the cause is found.
2. Reduce roundoff error accumulation which would occasionally cause
the test to fail, by choosing an overflow value which can be divided
by APB frequency.
3. Move time sampling part of the test into an IRAM function to
reduce variations due to cache behavior.
4. Remove calculation of "standard deviation" in the test, as what was
calculated was not actually standard deviation, and it did not add any
useful information.
The bug will cause memory corrupted (the largest range is from 0x3ffc0000 ~ 0x3ffc8000),
some strange error will happen, like IllegalInstruction, LoadProhibited and .etc.
Added:
* set a secure version in app/bootloader.
* description anti-rollback to ota part
* emulate the secure_version write and read operations
* efuse_em partition.
* a description about a rollback for native_ota_example.
Closes: TW26335
Move existing core dump files into espcoredump component folder
Add KConfig, linker.lf, make and CMakeList.txt for new component
Existing functionality separated into core_dump_common, core_dump_flash, core_dump_uart
Update test_core_dump.c and make files to link it as unit test
Update according to review:
Move target and RTOS related functionality into separated file (core_dump_port.c).
Fix following WiFi bugs:
1. Fix a crash bug which is caused by WiFi static TX buffer alloc/free.
2. Fix the bug that iphone fails to connect to ESP32 AP by enabling AP BAR receiving.
3. Fix the bug that ESP32 station fails to connect some APs, such as Xiaomi hotspot etc,
after reset.
Files where stack protector is initialized should not be compiled with
stack protector enabled. This was done for Make but missing for CMake.
Fixes https://github.com/espressif/esp-idf/issues/2990.
This commit adds the ability for backtracing to trace from the itnerrupt to the
task stack, and across nested interrupts. Test cases have also been added.
1. during parent selection, when scanning a MAP without ext-assoc IE, it will be handled as it has the same router BSSID as itself.
2. for MAP, when its client leaves, always post SYSTEM_EVENT_AP_STADISCONNECTED to mesh layer regardless of whether the client has passed the encrypted authentication or not.
Previously, hardware SHA engine "locks" were mutex semaphores. This meant that the task which
started a particular SHA session (in hardware) needed to finalise that session, or an invalid
FreeRTOS state was created.
Replace with binary semaphore which can be shared between tasks.
Includes a unit test, but unit test doesn't crash even without this fix
(some other unknown condition is required).
Due to a hardware limitation in ESP32, the first four bytes of some
CSI data is invalid, not the last four bytes.
Correct a mistake of CSI sub-carrier index in documentation.
1. detect and fix root conflicts when router BSSID is not set.
2. when root can not connect to the router due to NO_MORE_STAS(reason code:5), root will stop re-connection and perform MESH_NWK_LOOK_FOR_NETWORK.
3. wifi: fix the disconnection caused by receiving a deauth frame from non-parent node during scanning.
4. fix routing table redundant issue.
5. modify the max routes limitation from 300 to 1000.
6. wifi: fix ap does not deauth sta which has not completed the 4-way handshake.
1. esp32-pico use standard spi driver to access psram
2. for esp32-pico, flash and psram share the clock
3. for esp32-pico, psram cs io can be overwrite via menuconfig
timer_process_alarm function of esp_timer holds a spinlock for the
entire duration of its operation, except for the time when timer
callback function is called. It is possible that when
timer_process_alarm releases the spinlock, a higher priority task may
run and delete the timer. Then the execution will return to
timer_process_alarm, and this will either cause a crash, or undesired
execution of callback after the timer has been stopped or deleted.
To solve this problem, add a mutex which will prevent deletion of timers
while callbacks are being dispatched.
state and reduce force receiving broadcast data time
1. If receiving beacon which indicates that there is no data buffered,
do not force to receive WiFi data.
2. If receiving beacon which indicates that there is broadcast data
buffered, reduce the time to force receiving broadcast data.
1. when no parent is found, send probe request via broadcast.
2. fix memory leak caused by the remove announcement being sent is not released when esp_mesh_stop() is called.
3. fix modify IE encrypt after mesh is started.
4. ignore esp_mesh_connect() if mesh automatic reconnection is enabled.
5. fix reason is cleared before vote is done.
1. fix STAs can not detect disconnection from AP when encrypt transmission is used.
2. fix can not find hidden APs.
3. for root, modify the active scan time to 120ms.
4. remove all rc when clear parent Wi-Fi configuration.
5. fix error in checking Wi-Fi commit ID.
* Prevents section type conflict errors if (say) const & non-const data
is put into the same section (ie with DRAM_ATTR)
* Allows linker --gc-sections to remove unused custom sections
This fix includes following changes:
1. Fix the bug that esp_restart()/esp_wifi_stop() sometimes fails in WiFi/BT coexist mode.
2. Add a timer for WiFi stop and stop WiFi forcibly once the timer expires.
1. start an esp_timer on entering sleep to acquire pm_lock before wake up from modem sleep
2. decrease the clock division of XTAL fed to bluetooth low power clock from 32us to 2us period to allow to work under 240MHz Max CPU frequency
3. decrease the minimum sleep duration threshold to allow shorter bluetooth modem sleep period, especially for BLE with short connection interval
4. reconfigure bluetooth baseband(BT-BB) settings after PHY/RF init upon waking up from modem sleep to avoid packet RX/TX performance degradation
1. Fix interrupt watchdog timeout in bluetooth "btdm_bb_isr"
2. Fix BLE assert(512) or assert(1536) in rwble.c at line 222
3. Update librtc.a to fix BLE assert(512) in rwble.c at line 222
The #1 and #2 occurs random.
The #3 bug occurs in certain scenario:
1. If Wifi start softap and BLE is working
2. If wifi start station, but do not use normal station operation, such
as just use espnow, while BLE is working
3. Any other scenario, that wifi works without use software coexist
operation, while BLE is working(such as do advertising and ...)
4. update libcoexist.a version to v1.1.2
Added a new structure esp_app_desc_t. It has info about firmware:
version, secure_version, project_name, time/date build and IDF version.
Added the ability to add a custom structure with a description of the firmware.
The esp_app_desc_t is located in fixed place in start of ROM secotor. It is located after structures esp_image_header_t and esp_image_segment_header_t.
app_version is filed from PROJECT_VER variable (if set in custom make file) or PROJECT_PATH/version.txt or git repo (git describe).
Add API to get app_desc from partition.
1. Use BIT[7:5] of EID to determine psram size
2. Add ID support for 16Mbit psram
3. Remove module reset on SPI1
4. Confirmed with the vendor that only the old 32Mbit psram need special clock timing. For other psram chips, we should use standard QPI mode.
1. add network channel switch function.
- users can obtain the new channel through the event MESH_EVENT_CHANNEL_SWITCH.
- the entire network will be moved to the same channel as the router without user intervention.
- if no router is in the network, users can call esp_mesh_switch_channel() on the root side to
move the entire network to their desired channel.
2. support not configuring the network channel.
3. support not configuring the router BSSID even if the router is hidden.
4. add allow_channel_switch to mesh configuration.
- if the channel is not specified, this value will be ignored.
- if the channel is specified and this value is set, when "fail" (mesh_attempts_t) times of parent selection
or look for networks are reached, device will change to perform a full channel scan for networks that could join.
- if the channel is specified and this value is set to 0, when a root is not elected, channel switch is not allowed.
but when a root appears, the root performs a full channel scan during the process of connecting to the router,
so even allow_channel_switch is set to 0, the root may still switch channel and eventually the entire network
changes channel.
5. add allow_router_switch to mesh router configuration.
- if the BSSID of router is not specified, this value will be ignored.
- if the BSSID of router is specified and this value is set, when the router of this specified BSSID fails to be found
after "fail" (mesh_attempts_t) times, the entire network is allowed to switch to another router with the same SSID.
6. modify the root to perform a full channel scan when esp_wifi_connect().
7. support handling beacon without DS Paramter Set.
Fix some WiFi bugs:
1. Enable RX BAR
2. Fix the bug that ESP32 AP negotiates with iphone to 11g
3. Fix the bug that ESP32 STA has ap_loss because CMCC AP contains two SSID
1. fix failture of mesh stop caused by block-sending.
2. fix when FIXED_ROOT is set, 2nd layer devices can not receive mesh event ESP_ERR_MESH_NO_PARENT_FOUND.
3. fix when FIXED_ROOT is set and the root turns off mesh function, 2nd layer devices do not look for new parents.
4. add APIs esp_mesh_disconnect() and esp_mesh_connect().
5. disconnect from parent/router when the DSSS channel in received beacon is different from the home channel.
6. remove nvs task to release 3k bytes memory.
If zero-overhead loop buffer is enabled, under certain rare conditions
when executing a zero-overhead loop, the CPU may attempt to execute an invalid instruction. Work around by disabling the buffer.
New unity component can be used for testing other applications.
Upstream version of Unity is included as a submodule.
Utilities specific to ESP-IDF unit tests (partitions, leak checking
setup/teardown functions, etc) are kept only in unit-test-app.
Kconfig options are added to allow disabling certain Unity features.
Background
Softap will send connected event after receive assoc request as before, however, STA didn't connect to softAP if need security. As our mesh design, it will send data packet after receive connected event, so change the current behavior, softAP will send connected event if have encryption
Support for HSPI to output clock for 4M SPIRAM introduced regression
in clock configuration affecting SPIRAM access with 80MHz clock. This
commit fixes the issue.
1. call esp_timer_get_time and ref_clock_get in the same order on
start and in the loop
2. disable interrupts when calculating delta between ref_clock
and esp_timer
3. ensure both functions are in cache before calculating the delta
1. fix ap_loss that occurs when the parent turns off the mesh function and becomes a normal WiFi with a different SSID.
2. add an event MESH_EVENT_NETWORK_STATE that contains information about whether there is a root in the current network.
3. modify the mechanism of mesh IE update.
4. fix a problem in the process of re-voting to select the root, the device that does not meet the conditions of being a root votes for itself.
5. fix an issue that occurs in esp_mesh_recv_toDS() when stopping the mesh.
6. when the user specifies a parent for the device, the device will set the authmode and password of its AP mode to the same value as the specified parent.
7. add two disconnected reason codes MESH_REASON_EMPTY_PASSWORD and MESH_REASON_PARENT_UNENCRYPTED.
This commit resolves a blocking in esp_aes_block function.
Introduce:
The problem was in the fact that AES is switched off at the moment when he should give out the processed data. But because of the disabled, the operation can not be completed successfully, there is an infinite hang. The reason for this behavior is that the registers for controlling the inclusion of AES, SHA, MPI have shared registers and they were not protected from sharing.
Fix some related issue with shared using of AES SHA RSA accelerators.
Closes: https://github.com/espressif/esp-idf/issues/2295#issuecomment-432898137
When light sleep is finished on one CPU, it is possible that the other
CPU will enter light sleep again very soon, before interrupts on the
first CPU get a chance to run. To avoid such situation, set a flag
for the other CPU to skip light sleep attempt.
