When enable sleep reject before this fix, we have two limitations:
1. it must be light sleep
2. RTC GPIO wakeup source must be set
We require light sleep because `esp_deep_sleep_start` function has
been declared with "noreturn" attribute, So developers don't expect
that this function may return (due to an error or a sleep reject).
But the requirement for RTC GPIO wakeup source is not reasonable for
all chips. This requirement exists because ESP32 only supports RTC GPIO
and SDIO sleep reject sources. But later chips support all sleep reject
sources.
This fix brings the following changes:
for ESP32: RTC GPIO and SDIO sleep reject sources can be enabled
when corresponding wakeup source is set.
for later chips: all sleep reject sources can be enabled when
corresponding wakeup source is set.
Since ulp wakeup signal are connected to ulp int raw(except esp32), we
need to clear ulp int raw before sleep when ulp wakeup enabled. Otherwise,
if the ulp int raw is already set, chip will not sleep properly.
Closes https://github.com/espressif/esp-idf/issues/6229
introduced in e44ead5356
1. The int8M power domain config by default is PD. While LEDC is using
RTC8M as clock source, this power domain will be kept on.
But when 8MD256 is used as RTC clock source, the power domain should
also be kept on.
On ESP32, there was protection for it, but broken by commit
e44ead5356. Currently the power domain
will be forced on when LEDC is using RTC8M as clock source &&
!int8m_pd_en (user enable ESP_PDP_DOMAIN_RTC8M in lightsleep). Otherwise
the power domain will be powered off, regardless of RTC clock source.
In other words, int8M domain will be forced off (even when 8MD256
used as RTC clock source) if LEDC not using RTC8M as clock source, user
doesn't enable ESP_PDP_DOMAIN_RTC8M, or in deep sleep.
On later chips, there's no such protection, so 8MD256 could't be used as
RTC clock source in sleep modes.
This commit adds protection of 8MD256 clock to other chips. Fixes the
incorrect protection logic overriding on ESP32. Now the power domain
will be determiend by the logic below (order by priority):
1. When RTC clock source uses 8MD256, power up
2. When LEDC uses RTC8M clock source, power up
3. In deepsleep, power down
4. Otherwise determined by user config of ESP_PDP_DOMAIN_RTC8M,
power down by default. (This is preferred to have highest
priority, but it's kept as is because of current code structure.)
2. Before, after the macro `RTC_SLEEP_CONFIG_DEFAULT` decides dbias, the
protection above may force the int8m PU. This may cause the inconsistent
of dbias and the int8m PU status.
This commit lifts the logic of pd int8m/xtal fpu logic to upper layer
(sleep_modes.c).
Related: https://github.com/espressif/esp-idf/issues/8007, https://github.com/espressif/esp-idf/pull/8089
temp
Moved the following kconfig options out of the target component:
* CONFIG_ESP*_DEFAULT_CPU_FREQ* -> esp_system
* ESP*_REV_MIN -> esp_hw_support
* ESP*_TIME_SYSCALL -> newlib
* ESP*_RTC_* -> esp_hw_support
Where applicable these target specific konfig names were merged into
a single common config, e.g;
CONFIG_ESP*_DEFAULT_CPU_FREQ -> CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ
This commit refactors the ulp component.
Files are now divided based on type of ulp, viz., fsm or risc-v.
Files common to both are maintained in the ulp_common folder.
This commit also adds menuconfig options for ULP within the ulp
component instead of presenting target specific configuations for ulp.
The following files were deleted:
- components/esp_hw_support/include/soc/cpu.h
- components/soc/esp32s3/include/soc/cpu.h
The following functions are deprecated:
- get_sp()
The following functions declared in soc/cpu.h are now moved to esp_cpu.h:
- esp_cpu_configure_region_protection()
The following functions declared in soc/cpu.h are now moved to components/xtensa/include/esp_cpu_utils.h:
- esp_cpu_process_stack_pc()
All files with soc/cpu.h inclusion are updated to include esp_cpu.h instead.
Signed-off-by: Sudeep Mohanty <sudeep.mohanty@espressif.com>
