1. Change wifi scan duration from 120ms to 100ms
2. Using deport reg instead of ahb
3. Revert to report specific reason code when receiving deauth during 4-way-handshark
4. Fix the bug that tx ampdu parameter is not from peer device
5. Faster WiFi station connect improvement, avoid 100ms passive scan
6. Add FCS failed packets filter
7.Update esp32 phy lib to v4660
8.Fix country code last byte to space instead of NULL
9.Fix softap cannot forward A-MSDU
10.Fix some typos in esp_wifi.h
11.Fix max tx power to 20dBm
12.Fix the issue that the esp_wifi_sta_get_ap_info can't get country
13.Add support for 802.1x sha256 auth key mode
Rewrite ble dynamic prio to fix ble disconn in conn_param_update/channel_map_update
Rewrite ble dynamic prio in connection establishment
Fix ble dynamic prio with latency
Fix status bit set error when conn fail
1. Add STA checks during STA PMF operations
2. Fix WPA2-Ent issue with Open AP
3. Skip WPA-TKIP profile if PMF is required
4. Skip & clear Supplicant PMK Cache with mismatching AP config
5. Use flag ESP32_WIFI_ENABLE_WPA3_SAE to control WPA3 code, disabling
it code footprint reduces by 7.7kB in libwpa_supplicant.a
6. Fix handling of multiple AP credentials in WPS, apps need update
to handle the new event for the fix to work
Closes https://github.com/espressif/esp-idf/issues/5971
H/W decryption of Mgmt frames was disabled for PMF and done through
S/W. If ESPNOW packets go through this path, it affects backward
compatibility since method of decrypting Mgmt packets is different in H/W.
To address PMF + ESPNOW Co-existance, CCMP decryption method is modified
for ESPNOW packets so that they can be decrypted correctly. Since Tx
of ESPNOW packets can still be done in H/W alongside PMF, no change
required in encryption method in S/W.
Co-Authored-By: Nachiket Kukade <nachiket.kukade@espressif.com>
Co-Authored-By: zhangyanjiao <zhangyanjiao@espressif.com>
Co-Authored-By: kapil.gupta <kapil.gupta@espressif.com>
1. Fix FIX-ROOT does not reconnect to router when disconnect reason is too many
2. Add API esp_mesh_print_scan_result
3. Modify not to reset mesh_xonseq of self and children when flush_upstream_packets
4. Fix not switch to a parent candidate which has the same layer and assoc as current parent
5. Fix not arm parent monitor when a parent candidate is cleared without sending an event to mesh layer
6. Fix the new voted root does not reconnect to router if rssi is weak
1. Modify LR for esp32 and esp32s2
2. Fix esp32s2 RTS rate
3. Optimize some debug logs for probe response
4. Optimize phy and soc files
5. Fix the bug that no event for connect
6. drop receiving packets from myself
1. add sta connect again ap sent disconnect event
2. add set/get inactive time api
3. fix connect hidden AP doesn't update information
4. add rf test long short support
1. Fix TX DMA buffer issue
2. API esp_wifi_get_config add acquisition sta.listen_interval
3. Configure bandwidth and phy mode to store NVS
4. If AP's tsf has been restarted, STA will disconnect from AP.
5. Do not reset softAP's tsf except it restart
6. Fix the WiFi regdomain update bug
7. Fix WiFi fragment issue
Replace periph_module_enable/disable by periph_wifi_bt_common_module_enable which are in IRAM.
AddIRAM_ATTR periph_ll_wifi_bt_module_enable_clk_clear_rstandIRAM_ATTR periph_ll_wifi_bt_module_disable_clk_set_rstto fit O0 optimization level.
Delete duplicated spinlock and counter.
1. If the root is specified (FIXED-ROOT) by set type or set parent, change ie.mesh_type to MESH_ROOT before connect to router.
2. Release esp_mesh_recv_toDS when the root becomes non-root.
3. esp_mesh_set_type now supports MESH_IDLE and MESH_STA.
4. Fix ie.rc_rssi is not updated during scan and vote.
5. Fix ie.mesh_type do not match ie.layer caused by parent switch.
6. Fix during root switch, the original root doesn't disconnect from the router after it receives the switch request from the new voted root. (root switch happens by invoking esp_mesh_waive_root).
7. Fix the routing announce timer is not stopped immediately in a new root if the new root is transformed from non-root.
8. Choose the candidate with less ie.assoc when doing parent switch.
1. remove warning log when mesh is started:
Error! Should use default passive scan time parameter for WiFi scan when Bluetooth is enabled!!!!!!
2. remove abort when mesh is started:
Error! Should enable WiFi modem sleep when both WiFi and Bluetooth are enabled!!!!!!
Added following as part of this change
1. Removed auth_changed event
2. Updated doc regarding usage of WPA/WEP secuiry modes
3. Fixed WPA2 enterprise authmode threshold.
