1. Add more notification events to the enum according to the event list in AVRCP specification.
2. Add API and callback events for basic AVRCP target functionalities to do init, deinit, callback-registration, connection status indication.
3. Implement API to set/get supported PASSTHROUGH command on local AVRCP TG, implement callback events for remote passthrough command indication.
4. Implement API to set/get supported notification eventIDs on local AVRCP TG, implement API to send event notifications to remote CT. \
Currently supported event in TG only includes ESP_AVRC_RN_VOLUME_CHANGE(0xd), which can be extended in later commits.
5. Implement callback events for SetAbsoluteVolume command indication on TG.
6. Add limitation of event_ids supported in RegisterNotification command in CT. The supported event_ids include: \
ESP_AVRC_RN_PLAY_STATUS_CHANGE(0x1), ESP_AVRC_RN_TRACK_CHANGE(0x2), ESP_AVRC_RN_PLAY_POS_CHANGE(0x5), ESP_AVRC_RN_VOLUME_CHANGE(0xd).
7. Add feature bit mask in parameter of callback event ESP_AVRC_CT_REMOTE_FEATURES_EVT for peer feature information got from SDP.
8. Add API and callback event to AVRCP CT to retrieve remote TG's supported notification event capabilities.
9. Modify data type for parameter of callback event ESP_AVRC_CT_CHANGE_NOTIFY_EVT.
10. Change AVRCP version from 1.3 to 1.4 for compatibility cause in using AbsoluteVolume feature.
11. Modify local AVRCP device to be category 1 as CT and category 2 as TG that applies to bluetooth headphones or speakers.
12. Update the use of AVRCP APIs and events in the two examples: a2dp_sink and a2dp_gatts_coex, which include the demo of volume control and notification.
The current API is insufficient to allow the users to set different combinations of connection and discoverable mode
Users should be able to choose the device modes independently:
1. Connectable-
i. Non-connectable mode
ii. Connectable mode
2. Discoverable-
i. Non-discoverable mode
ii. Limited discoverable mode
iii. General discoverable mode
1. BLE only with 9(max) connection will decrease 3K DRAM
2. BR/EDR only with 7(max) connection will decrease 16K DRAM
3. Any of BLE or BR/EDR connection number decrease will also decrease DRAM consumption
4. Decrease one BLE connection will save about 1KB DRAM
5. Decrease one BR/EDR ACL connection will save about 1.2KB DRAM
6. Decrease one BR/EDR SCO/eSCO will save 2KB DRAM.
7. fix some definition and kconfig
8. remove 1.2k of vhci tx cache and make .bss & .data to heap about 1.4K
9. modify BT Reserved Memory size and modify example to support new bt kconfig
This change adds a check for compatibility between the nvs version
found on nvs flash and the one assumed by running code during nvs
initialization. Any mismatch is reported to the user using new error
code ESP_ERR_NVS_NEW_VERSION_FOUND.
Earlier they have to be selected at the compile time through sdkconfig.
A2DP sink and source application tested with this change.
Signed-off-by: Amey Inamdar <amey@espressif.com>
1. remove the feature mask parameter from AVRC connection state event, as the AVCTP connection can be initiated by remote device before service discovery to remote device is performed. \
In this case, AVRCP connection state event may not be reported after connection initated by remote device is established.
2. remove ESP_AVRC_CT_MAX_EVT
3. add more documentations to AVRC APIs
1. fix the bug. Modify the condition that esp_bt_controller_mem_release() shoud be only called before esp_bt_controller_init() or after esp_bt_controller_deinit()
2. modify the example to use esp_bt_controller_mem_release()
NVS is used to store PHY calibration data, WiFi configuration, and BT
configuration. Previously BT examples did not call nvs_flash_init,
relying on the fact that it is called during PHY init. However PHY init
did not handle possible NVS initialization errors.
This change moves PHY init procedure into the application, and adds
diagnostic messages to BT config management routines if NVS is not
initialized.
