Backport of https://github.com/apache/mynewt-nimble/pull/724
Mesh spec 1.0.1 changes proxy disabling behavior to only affect the
relaying from proxy nodes. Previously, disabling proxy would shut down
all proxy and node activity.
Tweaks from the original commit:
- Removed redundant call to bt_mesh_adv_update() in gatt_proxy_set()
- Removed invalid ref to 4.2.11.1 in node_identity_set()
---
According to Mesh Profile Spec 1.0.1, Section 4.2.11:
"If the Proxy feature is disabled, a GATT client device can connect
over GATT to that node for configuration and control. Messages from
the GATT bearer are not relayed to the advertising bearer."
Moreover some notes have been removed from the spec compared to
version 1.0:
Mesh Profile Spec 1.0, Section 4.2.11:
"Upon transition from GATT Proxy state 0x01 to GATT Proxy state 0x00
the GATT Bearer Server shall disconnect all GATT Bearer Clients."
"The Configuration Client should turn off the Proxy state as the last
step in the configuration process."
Mesh Profile Spec 1.0, Section 4.2.11.1:
"When the GATT Proxy state is set to 0x00, the Node Identity state
for all subnets shall be set to 0x00 and shall not be changed."
Until now the choice of reliable sending (segmented messages with
acks) was implicitly dependent on the size of the payload. Add a new
member to the bt_mesh_model_pub to force using segment acks even when
the payload would fit a single unsegmented message.
When PB-GATT support has been enabled the provisioning code "borrows"
the buffer from the proxy code. However, the way that initialization
was happening the proxy buffers were initialized only after
provisioning initialization, resulting in a corrupted buffer with
buf->data pointing to NULL. Reorder the initialization calls so that
proxy is done first and provisioning only after it.
Allow models to skip a periodic publish interval by returning an error
from the publish update callback.
Previously, an error return from publish update would cancel periodic
publishing. This can't be recovered from, and as such, no valid model
implementation could return an error from this callback, and there was
no way to skip a periodic publish.
The function bt_mesh_ctl_send() used to support maximum length of
11 bytes. The segmentation complies with the BLE Mesh Standard.
The ack is disabled in case of non unicast address.
The log in the spi_bus_lock_touch may be annoying. This commit suppress
the log level, and make the log visible only when the device altered.
Resolves https://github.com/espressif/esp-idf/issues/5056
Calloc function tries to allocate 4096 bytes.
If such memory is not available, it returns NULL pointer.
This exception was not handled in the code, causing a dirty crash.
In wifi station example, set PMF(Protected Management Frames)
configuration to capable. Set WPA3 Feature in menuconfig enabled
by default. This will allow device to establish more secured
connection with AP's that support these protocols.
Reduces write cycles, and useful on ESP32 ECO3 as UART_DIS_DL is protected by
the same efuse.
Also fixes accidental macro definition introduced in 7635dce502
esp_mqtt: Change an error print to use ESP_LOGE instead of ESP_LOGI
Move Sending MQTT connect message log from Info to Debug level
docs: Makes clear that publish API could block
Change the message printed after MQTT connection failure
Closes https://github.com/espressif/esp-idf/issues/5077
(by means of referencing commit 615aeae0c2)
Use the configured esp-netif netmask to update the dhcp struct when
starting the server or starting the netif itself.
Use the netmask in dhcps setters and getters.
Previously only mesh node info is supported to be stored
in flash. So when trying to reset the node, we only need
to judge if the BLE_MESH_VALID flag is set.
Currently we support storing both node & Provisioner info
in flash, when trying to erase the node info from flash,
the BLE_MESH_NODE flag will be checked. So we need to set
bt_mesh.flags to 0 when all the erase operations are done.
BSDs and Unices defined some non standardised functions and symbols used
for endianness handling: converting from Little Endian to Big Endian,
converting from Host to a specific representation, converting from a
specific representation to Host.
With this commit, a modified version of those symbols provided by
FreeBSD is imported.
The license of the imported code is still 2-Clause BSD.
Signed-off-by: Francesco Giancane <francesco.giancane@accenture.com>
Closes https://github.com/espressif/esp-idf/pull/4784
Programs and libraries using compiler and system information about
endianness often include the system header `<endian.h>`.
In `xtensa-gcc` compiler with `newlib` distribution, that file is located in
`<machine/endian.h>`; this means that `#include <endian.h>` would fail
at compile time.
This commit fixes the issue by adding a compatibility `<endian.h>`
header which in turn just includes `<machine/endian.h>`.
Signed-off-by: Francesco Giancane <francesco.giancane@accenture.com>
Merges https://github.com/espressif/esp-idf/pull/4784
A 0 length string is still a valid input and should be treated as such, a NULL return should be reserved for when errors occur during line editing or EOF is reached.
Merges https://github.com/espressif/esp-idf/pull/4926
- Adds HID Host support in Buedroid
- Adds BLE HID Host and Device support
- Adds some general HID utilities and definitions to help integrate with other stacks and native USB
* Keep only USB related register operations in the LL.
* Move pad-related logic into the driver.
* Driver is now responsible for enabling the peripheral.
