esp-idf/components/driver/Kconfig

255 lines
12 KiB
Plaintext
Raw Normal View History

menu "Driver configurations"
menu "ADC configuration"
config ADC_FORCE_XPD_FSM
bool "Use the FSM to control ADC power"
default n
help
ADC power can be controlled by the FSM instead of software. This allows the ADC to
be shut off when it is not working leading to lower power consumption. However
using the FSM control ADC power will increase the noise of ADC.
config ADC_DISABLE_DAC
bool "Disable DAC when ADC2 is used on GPIO 25 and 26"
default y
help
If this is set, the ADC2 driver will disable the output of the DAC corresponding to the specified
channel. This is the default value.
For testing, disable this option so that we can measure the output of DAC by internal ADC.
endmenu # ADC Configuration
menu "MCPWM configuration"
depends on SOC_MCPWM_SUPPORTED
config MCPWM_ISR_IN_IRAM
bool "Place MCPWM ISR function into IRAM"
default n
help
If this option is not selected, the MCPWM interrupt will be deferred when the Cache
is in a disabled state (e.g. Flash write/erase operation).
Note that if this option is selected, all user registered ISR callbacks should never
try to use cache as well. (with IRAM_ATTR)
endmenu # MCPWM Configuration
menu "SPI configuration"
config SPI_MASTER_IN_IRAM
bool "Place transmitting functions of SPI master into IRAM"
default n
select SPI_MASTER_ISR_IN_IRAM
help
Normally only the ISR of SPI master is placed in the IRAM, so that it
can work without the flash when interrupt is triggered.
For other functions, there's some possibility that the flash cache
miss when running inside and out of SPI functions, which may increase
the interval of SPI transactions.
Enable this to put ``queue_trans``, ``get_trans_result`` and
``transmit`` functions into the IRAM to avoid possible cache miss.
During unit test, this is enabled to measure the ideal case of api.
config SPI_MASTER_ISR_IN_IRAM
bool "Place SPI master ISR function into IRAM"
default y
help
Place the SPI master ISR in to IRAM to avoid possible cache miss.
Also you can forbid the ISR being disabled during flash writing
access, by add ESP_INTR_FLAG_IRAM when initializing the driver.
config SPI_SLAVE_IN_IRAM
bool "Place transmitting functions of SPI slave into IRAM"
default n
select SPI_SLAVE_ISR_IN_IRAM
help
Normally only the ISR of SPI slave is placed in the IRAM, so that it
can work without the flash when interrupt is triggered.
For other functions, there's some possibility that the flash cache
miss when running inside and out of SPI functions, which may increase
the interval of SPI transactions.
Enable this to put ``queue_trans``, ``get_trans_result`` and
``transmit`` functions into the IRAM to avoid possible cache miss.
config SPI_SLAVE_ISR_IN_IRAM
bool "Place SPI slave ISR function into IRAM"
default y
help
Place the SPI slave ISR in to IRAM to avoid possible cache miss.
Also you can forbid the ISR being disabled during flash writing
access, by add ESP_INTR_FLAG_IRAM when initializing the driver.
endmenu # SPI Configuration
menu "TWAI configuration"
depends on SOC_TWAI_SUPPORTED
config TWAI_ISR_IN_IRAM
bool "Place TWAI ISR function into IRAM"
default n
help
Place the TWAI ISR in to IRAM. This will allow the ISR to avoid
cache misses, and also be able to run whilst the cache is disabled
(such as when writing to SPI Flash).
Note that if this option is enabled:
- Users should also set the ESP_INTR_FLAG_IRAM in the driver
configuration structure when installing the driver (see docs for
specifics).
- Alert logging (i.e., setting of the TWAI_ALERT_AND_LOG flag)
will have no effect.
config TWAI_ERRATA_FIX_BUS_OFF_REC
bool "Add SW workaround for REC change during bus-off"
depends on IDF_TARGET_ESP32
default y
help
When the bus-off condition is reached, the REC should be reset to 0 and frozen (via LOM) by the
driver's ISR. However on the ESP32, there is an edge case where the REC will increase before the
driver's ISR can respond in time (e.g., due to the rapid occurrence of bus errors), thus causing the
REC to be non-zero after bus-off. A non-zero REC can prevent bus-off recovery as the bus-off recovery
condition is that both TEC and REC become 0. Enabling this option will add a workaround in the driver
to forcibly reset REC to zero on reaching bus-off.
config TWAI_ERRATA_FIX_TX_INTR_LOST
bool "Add SW workaround for TX interrupt lost errata"
depends on IDF_TARGET_ESP32
default y
help
On the ESP32, when a transmit interrupt occurs, and interrupt register is read on the same APB clock
cycle, the transmit interrupt could be lost. Enabling this option will add a workaround that checks the
transmit buffer status bit to recover any lost transmit interrupt.
config TWAI_ERRATA_FIX_RX_FRAME_INVALID
bool "Add SW workaround for invalid RX frame errata"
depends on IDF_TARGET_ESP32
default y
help
On the ESP32, when receiving a data or remote frame, if a bus error occurs in the data or CRC field,
the data of the next received frame could be invalid. Enabling this option will add a workaround that
will reset the peripheral on detection of this errata condition. Note that if a frame is transmitted on
the bus whilst the reset is ongoing, the message will not be receive by the peripheral sent on the bus
during the reset, the message will be lost.
config TWAI_ERRATA_FIX_RX_FIFO_CORRUPT
bool "Add SW workaround for RX FIFO corruption errata"
depends on IDF_TARGET_ESP32
default y
help
On the ESP32, when the RX FIFO overruns and the RX message counter maxes out at 64 messages, the entire
RX FIFO is no longer recoverable. Enabling this option will add a workaround that resets the peripheral
on detection of this errata condition. Note that if a frame is being sent on the bus during the reset
bus during the reset, the message will be lost.
endmenu # TWAI Configuration
2019-08-26 05:14:15 -04:00
menu "UART configuration"
config UART_ISR_IN_IRAM
bool "Place UART ISR function into IRAM"
default n
help
If this option is not selected, UART interrupt will be disabled for a long time and
may cause data lost when doing spi flash operation.
endmenu # UART Configuration
menu "GPIO Configuration"
config GPIO_ESP32_SUPPORT_SWITCH_SLP_PULL
bool "Support light sleep GPIO pullup/pulldown configuration for ESP32"
depends on IDF_TARGET_ESP32
help
This option is intended to fix the bug that ESP32 is not able to switch to configured
pullup/pulldown mode in sleep.
If this option is selected, chip will automatically emulate the behaviour of switching,
and about 450B of source codes would be placed into IRAM.
endmenu # GPIO Configuration
2021-11-07 21:26:52 -05:00
menu "GDMA Configuration"
depends on SOC_GDMA_SUPPORTED
2021-11-07 21:26:52 -05:00
config GDMA_CTRL_FUNC_IN_IRAM
bool "Place GDMA control functions into IRAM"
default n
help
Place GDMA control functions (like start/stop/append/reset) into IRAM,
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
Enabling this option can improve driver performance as well.
config GDMA_ISR_IRAM_SAFE
bool "GDMA ISR IRAM-Safe"
default n
help
This will ensure the GDMA interrupt handler is IRAM-Safe, allow to avoid flash
cache misses, and also be able to run whilst the cache is disabled.
(e.g. SPI Flash write).
endmenu # GDMA Configuration
menu "GPTimer Configuration"
config GPTIMER_CTRL_FUNC_IN_IRAM
bool "Place GPTimer control functions into IRAM"
default n
help
Place GPTimer control functions (like start/stop) into IRAM,
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
Enabling this option can improve driver performance as well.
config GPTIMER_ISR_IRAM_SAFE
bool "GPTimer ISR IRAM-Safe"
default n
help
Ensure the GPTimer interrupt is IRAM-Safe by allowing the interrupt handler to be
executable when the cache is disabled (e.g. SPI Flash write).
config GPTIMER_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy timer group driver (driver/timer.h).
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
config GPTIMER_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for GPTimer driver.
Note that, this option only controls the GPTimer driver log, won't affect other drivers.
endmenu # GPTimer Configuration
menu "PCNT Configuration"
depends on SOC_PCNT_SUPPORTED
config PCNT_CTRL_FUNC_IN_IRAM
bool "Place PCNT control functions into IRAM"
default n
help
Place PCNT control functions (like start/stop) into IRAM,
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
Enabling this option can improve driver performance as well.
config PCNT_ISR_IRAM_SAFE
bool "PCNT ISR IRAM-Safe"
default n
help
Ensure the PCNT interrupt is IRAM-Safe by allowing the interrupt handler to be
executable when the cache is disabled (e.g. SPI Flash write).
config PCNT_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy PCNT driver (driver/pcnt.h).
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
config PCNT_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for PCNT driver.
Note that, this option only controls the PCNT driver log, won't affect other drivers.
endmenu # PCNT Configuration
endmenu # Driver configurations