I2C is a serial, synchronous, multi-device, half-duplex communication protocol that allows co-existence of multiple masters and slaves on the same bus. I2C uses two bidirectional open-drain lines: serial data line (SDA) and serial clock line (SCL), pulled up by resistors.
Additionally, the {IDF_TARGET_NAME} chip has 1 low-power (LP) I2C controller. It is the cut-down version of regular I2C. Usually, the LP I2C controller only support basic I2C functionality with a much smaller RAM size, and does not support slave mode. For a full list of difference between HP I2C and LP I2C, please refer to the *{IDF_TARGET_NAME} Technical Reference Manual* > *I2C Controller (I2C)* > *Features* [`PDF <{IDF_TARGET_TRM_EN_URL}#i2c>`__].
You can use LP I2C peripheral when HP I2C is not sufficient for users' usage. But please note again the LP I2C does not support all HP I2C functions. Please read documentation before you use it.
Typically, an I2C slave device has a 7-bit address or 10-bit address. {IDF_TARGET_NAME} supports both I2C Standard-mode (Sm) and Fast-mode (Fm) which can go up to 100 kHz and 400 kHz respectively.
The frequency of SCL is influenced by both the pull-up resistor and the wire capacitance. Therefore, it is strongly recommended to choose appropriate pull-up resistors to make the frequency accurate. The recommended value for pull-up resistors usually ranges from 1 kΩ to 10 kΩ.
Keep in mind that the higher the frequency, the smaller the pull-up resistor should be (but not less than 1 KOhms). Indeed, large resistors will decline the current, which will increase the clock switching time and reduce the frequency. A range of 2 KOhms to 5 KOhms is recommended, but adjustments may also be necessary depending on their current draw requirements.
The legacy driver can't coexist with the new driver. Include ``i2c.h`` to use the legacy driver or the other two headers to use the new driver. Please keep in mind that the legacy driver is now deprecated and will be removed in future.
-`Resource Allocation <#resource-allocation>`__ - covers how to allocate I2C bus with properly set of configurations. It also covers how to recycle the resources when they finished working.
-`I2C Master Controller <#i2c_master_controller>`__ - covers behavior of I2C master controller. Introduce data transmit, data receive, and data transmit and receive.
-`I2C Slave Controller <#i2c_slave_controller>`__ - covers behavior of I2C slave controller. Involve data transmit and data receive.
-`Power Management <#power-management>`__ - describes how different source clock will affect power consumption.
-`IRAM Safe <#iram-safe>`__ - describes tips on how to make the I2C interrupt work better along with a disabled cache.
-`Thread Safety <#thread-safety>`__ - lists which APIs are guaranteed to be thread safe by the driver.
-`Kconfig Options <#kconfig-options>`__ - lists the supported Kconfig options that can bring different effects to the driver.
Both I2C master bus and I2C slave bus, when supported, are represented by :cpp:type:`i2c_bus_handle_t` in the driver. The available ports are managed in a resource pool that allocates a free port on request.
The I2C master bus is designed based on bus-device model. So :cpp:type:`i2c_master_bus_config_t` and :cpp:type:`i2c_device_config_t` are required separately to allocate the I2C master bus instance and I2C device instance.
I2C master bus requires the configuration that specified by :cpp:type:`i2c_master_bus_config_t`:
-:cpp:member:`i2c_master_bus_config_t::i2c_port` sets the I2C port used by the controller.
-:cpp:member:`i2c_master_bus_config_t::sda_io_num` sets the GPIO number for the serial data bus (SDA).
-:cpp:member:`i2c_master_bus_config_t::scl_io_num` sets the GPIO number for the serial clock bus (SCL).
-:cpp:member:`i2c_master_bus_config_t::clk_source` selects the source clock for I2C bus. The available clocks are listed in :cpp:type:`i2c_clock_source_t`. For the effect on power consumption of different clock source, please refer to `Power Management <#power-management>`__ section.
-:cpp:member:`i2c_master_bus_config_t::glitch_ignore_cnt` sets the glitch period of master bus, if the glitch period on the line is less than this value, it can be filtered out, typically value is 7.
-:cpp:member:`i2c_master_bus_config_t::intr_priority` sets the priority of the interrupt. If set to ``0`` , then the driver will use a interrupt with low or medium priority (priority level may be one of 1, 2 or 3), otherwise use the priority indicated by :cpp:member:`i2c_master_bus_config_t::intr_priority`. Please use the number form (1, 2, 3) , not the bitmask form ((1<<1), (1<<2), (1<<3)).
-:cpp:member:`i2c_master_bus_config_t::trans_queue_depth` sets the depth of internal transfer queue. Only valid in asynchronous transaction.
-:cpp:member:`i2c_master_bus_config_t::enable_internal_pullup` enables internal pullups. Note: This is not strong enough to pullup buses under high-speed frequency. A suitable external pullup is recommended.
If the configurations in :cpp:type:`i2c_master_bus_config_t` is specified, then :cpp:func:`i2c_new_master_bus` can be called to allocate and initialize an I2C master bus. This function will return an I2C bus handle if it runs correctly. Specifically, when there are no more I2C port available, this function will return :c:macro:`ESP_ERR_NOT_FOUND` error.
-:cpp:member:`i2c_device_config_t::dev_addr_length` configure the address bit length of the slave device. It can be chosen from enumerator :cpp:enumerator:`I2C_ADDR_BIT_LEN_7` or :cpp:enumerator:`I2C_ADDR_BIT_LEN_10` (if supported).
-:cpp:member:`i2c_device_config_t::device_address` sets the I2C device raw address. Please parse the device address to this member directly. For example, the device address is 0x28, then parse 0x28 to :cpp:member:`i2c_device_config_t::device_address`, don't carry a write or read bit.
-:cpp:member:`i2c_device_config_t::scl_speed_hz` sets the SCL line frequency of this device.
-:cpp:member:`i2c_device_config_t::scl_wait_us` sets the SCL await time (in μs). Usually this value should not be very small because slave stretch will happen in pretty long time (It's possible even stretch for 12 ms). Set ``0`` means use default register value.
Once the :cpp:type:`i2c_device_config_t` structure is populated with mandatory parameters, :cpp:func:`i2c_master_bus_add_device` can be called to allocate an I2C device instance and mounted to the master bus then. This function will return an I2C device handle if it runs correctly. Specifically, when the I2C bus is not initialized properly, calling this function will result in a :c:macro:`ESP_ERR_INVALID_ARG` error.
Given that i2c master handle has been initialized in some module(e.g. an audio module), an another module(e.g. a video module) is not convenient to reused the handle. We have a helper function, :cpp:func:`i2c_master_get_bus_handle` for getting the initialized handle via port. However, please make sure the handle has already been initialized ahead of time. Otherwise an error would be reported.
Install I2C master bus with LP I2C peripheral is almost as same as how HP I2C peripheral is installed. However, there are still some difference should be taken focus on, including IOs, clock sources, I2C port number, etc. Following code will show how to install I2C master bus with LP_I2C.
If a previously installed I2C bus or device is no longer needed, it's recommended to recycle the resource by calling :cpp:func:`i2c_master_bus_rm_device` or :cpp:func:`i2c_del_master_bus`, so as to release the underlying hardware.
-:cpp:member:`i2c_slave_config_t::i2c_port` sets the I2C port used by the controller.
-:cpp:member:`i2c_slave_config_t::sda_io_num` sets the GPIO number for serial data bus (SDA).
-:cpp:member:`i2c_slave_config_t::scl_io_num` sets the GPIO number for serial clock bus (SCL).
-:cpp:member:`i2c_slave_config_t::clk_source` selects the source clock for I2C bus. The available clocks are listed in :cpp:type:`i2c_clock_source_t`. For the effect on power consumption of different clock source, please refer to `Power Management <#power-management>`__ section.
-:cpp:member:`i2c_slave_config_t::send_buf_depth` sets the sending buffer length.
-:cpp:member:`i2c_slave_config_t::slave_addr` sets the slave address.
-:cpp:member:`i2c_master_bus_config_t::intr_priority` sets the priority of the interrupt. If set to ``0`` , then the driver will use a interrupt with low or medium priority (priority level may be one of 1, 2 or 3), otherwise use the priority indicated by :cpp:member:`i2c_master_bus_config_t::intr_priority`. Please use the number form (1, 2, 3), not the bitmask form ((1<<1), (1<<2), (1<<3)). Please pay attention that once the interrupt priority is set, it cannot be changed until :cpp:func:`i2c_del_master_bus` is called.
-:cpp:member:`i2c_slave_config_t::addr_bit_len`. Set this variable to ``I2C_ADDR_BIT_LEN_10`` if the slave should have a 10-bit address.
:SOC_I2C_SLAVE_CAN_GET_STRETCH_CAUSE:- :cpp:member:`i2c_slave_config_t::stretch_en`. Set this variable to true, then the slave controller stretch will work. Please refer to [`TRM <{IDF_TARGET_TRM_EN_URL}#i2c>`__] to learn how I2C stretch works.
:SOC_I2C_SLAVE_CAN_GET_STRETCH_CAUSE:- :cpp:member:`i2c_slave_config_t::broadcast_en`. Set this to true to enable the slave broadcast. When the slave receives the general call address 0x00 from the master and the R/W bit followed is 0, it responds to the master regardless of its own address.
:SOC_I2C_SLAVE_SUPPORT_I2CRAM_ACCESS:- :cpp:member:`i2c_slave_config_t::access_ram_en`. Set this to true to enable the non-FIFO mode. Thus the I2C data FIFO can be used as RAM, and double addressing will be synchronised opened.
:SOC_I2C_SLAVE_SUPPORT_SLAVE_UNMATCH:- :cpp:member:`i2c_slave_config_t::slave_unmatch_en`. Set this to true to enable the slave unmatch interrupt. If the command address sent by master can't match the slave address, then unmatch interrupt will be triggered.
Once the :cpp:type:`i2c_slave_config_t` structure is populated with mandatory parameters, :cpp:func:`i2c_new_slave_device` can be called to allocate and initialize an I2C master bus. This function will return an I2C bus handle if it runs correctly. Specifically, when there are no more I2C port available, this function will return :c:macro:`ESP_ERR_NOT_FOUND` error.
If a previously installed I2C bus is no longer needed, it's recommended to recycle the resource by calling :cpp:func:`i2c_del_slave_device`, so that to release the underlying hardware.
After installing the I2C master driver by :cpp:func:`i2c_new_master_bus`, {IDF_TARGET_NAME} is ready to communicate with other I2C devices. I2C APIs allow the standard transactions. Like the wave as follows:
After installing I2C master bus successfully, you can simply call :cpp:func:`i2c_master_transmit` to write data to the slave device. The principle of this function can be explained by following chart.
In order to organize the process, the driver uses a command link, that should be populated with a sequence of commands and then passed to I2C controller for execution.
After installing I2C master bus successfully, you can simply call :cpp:func:`i2c_master_receive` to read data from the slave device. The principle of this function can be explained by following chart.
Some I2C device needs write configurations before reading data from it. Therefore, an interface called :cpp:func:`i2c_master_transmit_receive` can help. The principle of this function can be explained by following chart.
Please note that no STOP condition bit is inserted between the write and read operations; therefore, this function is suited to read a register from an I2C device. A simple example for writing and reading from a slave device:
I2C driver can use :cpp:func:`i2c_master_probe` to detect whether the specific device has been connected on I2C bus. If this function return ``ESP_OK``, that means the device has been detected.
Pull-ups must be connected to the SCL and SDA pins when this function is called. If you get `ESP_ERR_TIMEOUT` while `xfer_timeout_ms` was parsed correctly, you should check the pull-up resistors. If you do not have proper resistors nearby, setting `flags.enable_internal_pullup` as true is also acceptable.
After installing the I2C slave driver by :cpp:func:`i2c_new_slave_device`, {IDF_TARGET_NAME} is ready to communicate with other I2C masters as a slave.
The send buffer of the I2C slave is used as a FIFO to store the data to be sent. The data will queue up until the master requests them. You can call :cpp:func:`i2c_slave_transmit` to transfer data.
Whenever the master writes data to the slave, the slave will automatically store data in the receive buffer. This allows the slave application to call the function :cpp:func:`i2c_slave_receive` as its own discretion. As :cpp:func:`i2c_slave_receive` is designed as a non-blocking interface, users need to register callback :cpp:func:`i2c_slave_register_event_callbacks` to know when the receive has finished.
I2C slave FIFO mentioned above can be used as RAM, which means user can access the RAM directly via address fields. For example, write data to the third RAM block with following graph. Before using this, please note that :cpp:member:`i2c_slave_config_t::access_ram_en` needs to be set to true.
Data can be stored in the RAM with a specific offset by the slave controller, and the master can read this data directly via the RAM address. For example, if the data is stored in the third RAM block, master can read this data by the following graph. Before using this, please note that :cpp:member:`i2c_slave_config_t::access_ram_en` needs to be set to true.
When an I2C master bus triggers an interrupt, a specific event will be generated and notify the CPU. If you have some functions that need to be called when those events occurred, you can hook your functions to the ISR (Interrupt Service Routine) by calling :cpp:func:`i2c_master_register_event_callbacks`. Since the registered callback functions are called in the interrupt context, users should ensure the callback function doesn't attempt to block (e.g. by making sure that only FreeRTOS APIs with ``ISR`` suffix are called from the function). The callback functions are required to return a boolean value, to tell the ISR whether a high priority task is woken up by it.
Although I2C is a synchronous communication protocol, asynchronous behavior is supported by registering above callbacks. In this way, I2C APIs will be non-blocking interface. But note that on the same bus, only one device can adopt asynchronous operation.
I2C master asynchronous transaction is still an experimental feature (The issue is that when asynchronous transaction is very large, it will cause memory problem).
-:cpp:member:`i2c_master_event_callbacks_t::on_recv_done` sets a callback function for master "transaction-done" event. The function prototype is declared in :cpp:type:`i2c_master_callback_t`.
When an I2C slave bus triggers an interrupt, a specific event will be generated and notify the CPU. If you have some function that needs to be called when those events occurred, you can hook your function to the ISR (Interrupt Service Routine) by calling :cpp:func:`i2c_slave_register_event_callbacks`. Since the registered callback functions are called in the interrupt context, users should ensure the callback function doesn't attempt to block (e.g. by making sure that only FreeRTOS APIs with ``ISR`` suffix are called from the function). The callback function has a boolean return value, to tell the caller whether a high priority task is woken up by it.
-:cpp:member:`i2c_slave_event_callbacks_t::on_recv_done` sets a callback function for "receive-done" event. The function prototype is declared in :cpp:type:`i2c_slave_received_callback_t`.
:SOC_I2C_SLAVE_CAN_GET_STRETCH_CAUSE:- :cpp:member:`i2c_slave_event_callbacks_t::on_stretch_occur` sets a callback function for "stretch" cause. The function prototype is declared in :cpp:type:`i2c_slave_stretch_callback_t`.
When the power management is enabled (i.e. :ref:`CONFIG_PM_ENABLE` is on), the system will adjust or stop the source clock of I2C FIFO before going into Light-sleep mode, thus potentially changing the I2C signals and leading to transmitting or receiving invalid data.
However, the driver can prevent the system from changing APB frequency by acquiring a power management lock of type :cpp:enumerator:`ESP_PM_APB_FREQ_MAX`. Whenever user creates an I2C bus that has selected :cpp:enumerator:`I2C_CLK_SRC_APB` as the clock source, the driver will guarantee that the power management lock is acquired when I2C operations begin and the lock will be released automatically when I2C operations finish.
If the controller clock source is selected to :cpp:enumerator:`I2C_CLK_SRC_REF_TICK`, then the driver won't install power management lock for it, which is more suitable for a low power application as long as the source clock can still provide sufficient resolution.
If the controller clock source is selected to :cpp:enumerator:`I2C_CLK_SRC_XTAL`, then the driver won't install power management lock for it, which is more suitable for a low power application as long as the source clock can still provide sufficient resolution.
By default, the I2C interrupt will be deferred when the cache is disabled for reasons like writing or erasing flash. Thus the event callback functions will not get executed in time, which is not expected in a real-time application.
The factory function :cpp:func:`i2c_new_master_bus` and :cpp:func:`i2c_new_slave_device` are guaranteed to be thread safe by the driver, which means that the functions can be called from different RTOS tasks without protection by extra locks. Other public I2C APIs are not thread safe, which means the user should avoid calling them from multiple tasks, if it is necessary to call them in multiple tasks, please add extra locks.
-:ref:`CONFIG_I2C_ISR_IRAM_SAFE` controls whether the default ISR handler can work when cache is disabled, see also `IRAM Safe <#iram-safe>`__ for more information.
-:ref:`CONFIG_I2C_ENABLE_DEBUG_LOG` is used to enable the debug log at the cost of increased firmware binary size.
