esp-idf/components/openthread/Kconfig

162 lines
5.7 KiB
Plaintext
Raw Normal View History

menu "OpenThread"
config OPENTHREAD_ENABLED
bool "OpenThread"
default n
help
Select this option to enable OpenThread and show the submenu with OpenThread configuration choices.
config OPENTHREAD_LOG_LEVEL_DYNAMIC
bool "Enable dynamic log level control"
depends on OPENTHREAD_ENABLED
default y
help
Select this option to enable dynamic log level control for OpenThread
choice OPENTHREAD_LOG_LEVEL
prompt "OpenThread log verbosity"
depends on OPENTHREAD_ENABLED && !OPENTHREAD_LOG_LEVEL_DYNAMIC
default OPENTHREAD_LOG_LEVEL_INFO
help
Select OpenThread log level.
config OPENTHREAD_LOG_LEVEL_NONE
bool "No logs"
config OPENTHREAD_LOG_LEVEL_CRIT
bool "Error logs"
config OPENTHREAD_LOG_LEVEL_WARN
bool "Warning logs"
config OPENTHREAD_LOG_LEVEL_NOTE
bool "Notice logs"
config OPENTHREAD_LOG_LEVEL_INFO
bool "Info logs"
config OPENTHREAD_LOG_LEVEL_DEBG
bool "Debug logs"
endchoice #OPENTHREAD_LOG_LEVEL
config OPENTHREAD_LOG_LEVEL
int
depends on OPENTHREAD_ENABLED && !OPENTHREAD_LOG_LEVEL_DYNAMIC
default 0 if OPENTHREAD_LOG_LEVEL_NONE
default 1 if OPENTHREAD_LOG_LEVEL_CRIT
default 2 if OPENTHREAD_LOG_LEVEL_WARN
default 3 if OPENTHREAD_LOG_LEVEL_NOTE
default 4 if OPENTHREAD_LOG_LEVEL_INFO
default 5 if OPENTHREAD_LOG_LEVEL_DEBG
2021-07-09 00:18:41 -04:00
choice OPENTHREAD_RADIO_TYPE
prompt "Config the Thread radio type"
depends on OPENTHREAD_ENABLED
default OPENTHREAD_RADIO_NATIVE if SOC_IEEE802154_SUPPORTED
2021-07-09 00:18:41 -04:00
default OPENTHREAD_RADIO_SPINEL_UART
help
Configure how OpenThread connects to the 15.4 radio
config OPENTHREAD_RADIO_NATIVE
bool "Native 15.4 radio"
help
Select this to use the native 15.4 radio.
config OPENTHREAD_RADIO_SPINEL_UART
bool "Connect via UART"
help
Select this to connect to a Radio Co-Processor via UART.
endchoice
choice OPENTHREAD_DEVICE_TYPE
prompt "Config the Thread device type"
depends on OPENTHREAD_ENABLED
default OPENTHREAD_FTD
help
OpenThread can be configured to different device types (FTD, MTD, Radio)
config OPENTHREAD_FTD
bool "Full Thread Device"
help
Select this to enable Full Thread Device which can act as router and leader in a Thread network.
config OPENTHREAD_MTD
bool "Minimal Thread Device"
help
Select this to enable Minimal Thread Device which can only act as end device in a Thread network.
This will reduce the code size of the OpenThread stack.
config OPENTHREAD_RADIO
bool "Radio Only Device"
help
Select this to enable Radio Only Device which can only forward 15.4 packets to the host.
The OpenThread stack will be run on the host and OpenThread will have minimal footprint on the
radio only device.
endchoice
config OPENTHREAD_CLI
bool "Enable Openthread Command-Line Interface"
depends on OPENTHREAD_ENABLED
default y
help
Select this option to enable Command-Line Interface in OpenThread.
config OPENTHREAD_DIAG
bool "Enable diag"
depends on OPENTHREAD_ENABLED
default y
help
Select this option to enable Diag in OpenThread. This will enable diag mode and a series of diag commands
in the OpenThread command line. These commands allow users to manipulate low-level features of the storage
and 15.4 radio.
config OPENTHREAD_COMMISSIONER
bool "Enable Commissioner"
depends on OPENTHREAD_ENABLED
default n
help
Select this option to enable commissioner in OpenThread. This will enable the device to act as a
commissioner in the Thread network. A commissioner checks the pre-shared key from a joining device with
the Thread commissioning protocol and shares the network parameter with the joining device upon success.
config OPENTHREAD_JOINER
bool "Enable Joiner"
depends on OPENTHREAD_ENABLED
default n
help
Select this option to enable Joiner in OpenThread. This allows a device to join the Thread network with a
pre-shared key using the Thread commissioning protocol.
config OPENTHREAD_SRP_CLIENT
bool "Enable SRP Client"
depends on OPENTHREAD_ENABLED
2022-12-26 06:05:19 -05:00
default y
help
Select this option to enable SRP Client in OpenThread. This allows a device to register SRP services to SRP
Server.
config OPENTHREAD_BORDER_ROUTER
bool "Enable Border Router"
depends on OPENTHREAD_ENABLED
default n
help
Select this option to enable border router features in OpenThread.
config OPENTHREAD_NUM_MESSAGE_BUFFERS
int "The number of openthread message buffers"
depends on OPENTHREAD_ENABLED
default 65
range 50 100
config OPENTHREAD_DNS64_CLIENT
bool "Use dns64 client"
depends on OPENTHREAD_ENABLED
default n
help
Select this option to acquire NAT64 address from dns servers.
config OPENTHREAD_UART_BUFFER_SIZE
int "The uart received buffer size of openthread"
depends on OPENTHREAD_ENABLED
default 256
range 128 1024
help
Set the OpenThread UART buffer size.
endmenu